walther p22 red dot mount 3d models
412285 3d models found related to walther p22 red dot mount.thingiverse
Walther P22 or similar airsoft pistol RMR or RIS mount. This part is based on the general concept for the Walther Brand bridge mount giving the user the ability to mount parts above the slide by mounting a bridge to a support under the rails and not...
thingiverse
This is a magazine loading assist for Walther P22. The model may be a bit tight,but it gets the job done. ... I would print it at mid-high resolution with at least 20% infill.
thingiverse
10rd and 13rd followers for walther P22 Magazines. In order to use the 14rd follower and retainer, you must count the coils on your spring. Aftermarket P22 Magazines come with 16 coils instead of the factory 23. ...If you are Modifying a factory...
thingiverse
I saw similar speed loaders, but did not see one that was specific for the Walther P22 magazines. This one works. When using, the hole in the base indicates the side that should be on the same side as the follower button. This object was made in...
thingiverse
Now you can store your Walther G22 & P22 magazines conveniently where your couldn't before, leaving you the clean and functional safe you always wanted. These "Mag Racks" are very versatile. Mounting options allow you to mount them virtually anywhere...
thingiverse
This is a conversion to convert your walther P22 factory magazine to a 15rd magazine. Besides the printed parts, you will need a new spring that can be found at taylor tactical. When installing the new base, it will take some effort because you have...
thingiverse
A small adapter to mount any basic red dot finder on a takahashi telescope.
thingiverse
Scope mount for an airsoft red dot sight, not meant for actual weapon sights.
thingiverse
This is a red dot mount design I whipped up in an afternoon as an experiment. ...It requires some minimal fitment, and also needs to be drilled and tapped before a red dot can be installed.
thingiverse
Speed Loader for Walther P22 7 x 9mm PAK 8 x 9mm PAK 10 x 9mm PAK
thingiverse
Parts needed: - 2 x M3 threaded inserts (4mm thick) - 2 x M2 threaded inserts (3-4mm thick) - 1 x Printed Mount I made this mount to fit a Holosun HS507K-X2. It's possible other optics mount to it, but I'm not sure what they'd be. Feel free to...
cults3d
Red Dot Picatinny Mount Riser Also need: - 01 M3 Screw 30mm - 01 M3 Bolt
cults3d
under barrel glock 44 red dot mount. but fits almost every glock.and the red dot is from amazon. ...and you need an m4 nut and a 30mm m4 allen bolt
thingiverse
Simple mount for Krasnar red dot on an 11mm wedge rail. ... Will require 2ea M4 bolts and 2ea self-locking nuts.
thingiverse
This is a rmr red dot sight mount for mk23. It clips on rear iron sight. Sits tighter than hadron design rail and the red dot is much lower. I recommend to thread holes before mounting the sight. ...If having trouble mounting it video should be helpful:...
thingiverse
Mounts to the lower Pic rail on the HK P30 in order to mount a red dot above the slide with just enough clearance to cycle. You will need #10 hardware to attach it. ... Don't mind the mismatched pics, couple versions.
thingiverse
This mount uses the hardware provided by Burgess Red Dot (Mounting Bar, (2) Machine Screws and (2) Nuts. The OEM fastener, (1) Allen Head, is used for the mounting of the OEM finder scope. Removed this screw and then replace the OEM mount with new...
thingiverse
Accidentally broke the red dot finder on my celestron telescope and decided to print out a new one since gluing didn't work so well.
thingiverse
This is an adapter to go from the lower pic rail to mount a red dot on the top of your Chiappa Rhino if you didn't get the 6" model with the upper mounting rail. It works with my 4" model but I'd limit the loads you run through it. It can take...
thingiverse
This is a working red dot sight mount for use on pistols or airsoft guns with a picatinny rail on them. It was sized to a Glock 19 specifically but will likely fit others that are smaller in slide width and height. Don't expect it to be as durable as...
thingiverse
This is likely the lowest Red Dot mount you can make, for an SKS. Even still, with this Viper attached, I am considering padding my stock by about half an inch, to get a proper cheek weld. But it will work without it, easily enough. This should...
thingiverse
... sind für M3 Schrauben und Muttern. Schrauben an Schlitt: 4x M3 7mm Gesamt inklusive Kopf!! Hey, here's a holder for micro red dots from Aliex... The holes are for M3 nuts and bolts. ... Screws to slide: 4x M3 7mm total including head!!
thingiverse
... sind für M3 Schrauben und Muttern. Schrauben an Schlitt: 4x M3 7mm Gesamt inklusive Kopf!! Hey, here's a holder for micro red dots from Aliex... The holes are for M3 nuts and bolts. ... Screws to slide: 4x M3 7mm total including head!!
cgtrader
Game ready model of a Walther MRS Multi Reticle Sight Open Reflex Sight Red Dot Optic. The glass included is ready to be setup for Parallax Occlusion Mapping projection of a Red Dot. MRS: 1,049 Verts and 2,098 Tris 2,048 x 2,048 texture maps are...
thingiverse
Because the original magazine base is too small for my hands I did a bigger one. ... This one is for the .22lr version.
thingiverse
This is a remix/combo of https://www.thingiverse.com/thing:3863046 and https://www.thingiverse.com/thing:4420037 I'm a novice at CAD, but it turned out well enough for me to use for my mags.