wanhao d6 mod 3d models

The single version https://www.thingiverse.com/thing:3609922 works fine, but the overhang tower was not perfect on the right side. So I mirrored my design and made a carrier to hold it. The blowers are very light and so the design is very straight on...

This clip prevents the ribbon cable on the extruder from popping off. Please note that it's been tweaked for my printer, specifically the length of the legs may need adjusting. It's a quick print, so try it out and see if it fits. ...The v3 version...

I needed a more versatile mount for my Logitech 910 HD webcam. To secure the camera, I remove the plate in its base as shown and attach the cam using two M2 12mm screws to the sliding mechanism. The mount fits snugly beneath the heated bed, allowing...

The single version at https://www.thingiverse.com/thing:3609922 works perfectly, but the overhang tower is slightly imperfect on its right side. So I mirrored my design and added a holder to secure it. The blowers are extremely lightweight, making...

This is a revised version of dot_bob's BLTouch mount.\r\nhttps://www.thingiverse.com/thing:2483813\r\n\r\nI made some adjustments to the screw mount area to ensure clearance for the screws that come with the BLTouch sensor.\r\n\r\nTo get the best...

This is a customized remix of the original housing found at https://www.thingiverse.com/thing:2134152, using only that component. The design includes a flexible roll top for the ribbon cable to run smoothly along, preventing any potential damage...

Spool holder with off switch makes it easy to avoid climbing over the printer when it's mounted against a wall, saving space and simplifying maintenance. The spool holder has been tested on bowden setups but should also work for direct drives. When...

This is a remix of TERRAoperative's ALREADY AWESOME Spool holder located here: https://www.thingiverse.com/thing:2526942. I modified the cones to accommodate larger filament spools, while maintaining compatibility with smaller ones. The design works...

You'll need to rewire your Print carriage's ribbon cable as part of installing a Duet Wifi board. ...A new cable, wrapped in a durable braided nylon casing, will be secured by the print head cap.

A sleek 40mm fan holder to match my entire collection of accessories. Print Settings Printer: Specifically designed for the Duplicator 6 printer model. Rafts: Optional, as it doesn't significantly impact the overall print quality. Supports:...

I've included two files for download: one compatible with my Wanhao v2 printer and another for v2.1 printers. I don't own a v2.1 myself but based my file on what a friend told me. You can watch this video of the mod in use at...

this mod was born from the need to remotely control (effectively) the wanhao gr2 with octoprint / octodash. for more info on configuration and software image (https://www.gdip.io/posts/3d-printing/wanhaogr2/). ... The parts needed for this...

... this STL but haven't attempted printing it yet. If issues arise, please let me know and I'll upload updates accordingly. Print Settings: Printer Brand: Wanhao Printer Model: Wanhao Duplicator i3 V2 Rafts Required: No Matter Supports Needed: Yes

This is a custom fan duct designed specifically for the Wanhao D5s Mini and built upon the foundation of http://www.thingiverse.com/thing:1499118.\nI have replaced the stock D5s hotend with an Ultimaker hotend nozzle, complete with Peek insulation...

Modification of the 120mm fan mod to fit a panel mount USB connector from Amazon, sold by B07F2Z54TY. The 90-degree USB fits perfectly with the MKS Gen_L adapter for the stock control box found on Thingiverse at thing:2895849. ...This setup makes it...

Top Mount Bracket to Spare Middle Plate Drilling When Installing Mod by fcollingwood. https://www.thingiverse.com/thing:3532447 No Support Required, External Face Printed on Bed for Finer Finish. Cover Holes with Thin Layer, Pierce Once Printed.

Modifying the 120mm fan mod to accommodate a panel mount USB connector is a straightforward process. The 90-degree USB fits seamlessly with the MKS Gen_L adapter, specifically designed for the stock control box available on Thingiverse...

Two files are available for download: one is designed specifically for Wanhao V2 printers, while the other is intended for V2.1 models. I based my design on information provided by a friend who owns these printers, so it's possible that the second...

This is a customized carriage for the Wanhao i3, designed and printed over an extended period of time to achieve maximum lightness and minimal weight. The primary reason behind designing this carriage lies in its ability to weigh significantly less...

This is a modification to replace two linear rods with a single MGN15C rail. Print two of the parts marked (2x) and one part marked (1x). ...The swap should be straightforward, but it's uncertain since this model uses the y-carriage from...

Here are a few parts you'll need to print that will convert your D7's horrible top cover into a front opening swing door. This conversion requires drilling and tapping of the top plate of the printer, as well as drilling a few more holes in the front...

I was thrilled to discover some filaments that were so coarse they wouldn't be pulled smoothly through the filament sensor and PTFE tube to the extruder from behind, especially with Fluorescent PLA and wood filaments. I repurposed existing designs to...

I finally decided to change the print head accessories on my Duplicator 6 after adding a BL Touch. The design was optimized to keep the full printing area available. Since I have a Bondtech direct drive extruder, there is clearance on the back. That...

This is a remix of a remix of a remix but it looks like the original design is [https://www.thingiverse.com/thing:2248473](https://www.thingiverse.com/thing:2248473) So this is where I remixed from. I made the filament guide hole to allow for...

Jan 1 2019 I suddenly had an epiphany about printing a stand that snaps onto rods and rests on the print bed, assuming the bed has been accurately leveled. This allows you to place the stand on it, ensuring perfect alignment of the rods from...

This adapted version of Wultz's cable clips is tailored for larger 6mm outer diameter/4mm inner diameter PTFE filament tubes. In comparison, the standard 2mm inner diameter tube exhibits significantly more friction than its 4mm counterpart. ...The...

I needed a more reliable base for my Logitech 910. The remarkable CMH mount served me well for quite some time. This mount attaches to the exposed door hinge pins on the printer. Not using ABS, I don't require an enclosure. The hinge is engineered...

Remixed from davidhbrown's thing: https://www.thingiverse.com/thing:3642996 I laser cut a door file that I found on FB, but could never find a hinge that worked with it, but this one was close, so I made a new door side part. ...The hinge parts from...

Moving the filament sensor to the top of the print head is crucial now that I'm feeding filament from above the printer (thing:2789243). Keeping the PTFE tube attached helps nicely manage cables. For more information on filament run out sensors,...

Features: - Walls are thicker to prevent thin vertical walls from splitting - Only 9.5mm in height, allowing for a larger gap between the holder and the print - The design is much sturdier due to a shorter shaft connecting the two fans - An optional...