wanhao duplicator 4s z axis brace and bushing 3d models

Braced version of Martin, Pawel & Neil's Wanhao Duplicator 6 - Double Axial Fan Shroud. There is some variance in clearances of the D6, so I have included thinner mounting spacers. IMPORTANT I only recommend this design if you are solely printing...

Corners of top plug secured by duplicator four S cover.\ Fit precisely into corner holes; however, slight filing on inner corners was required since my duplicator four S produced an unsatisfactory angle (my experience still limited).\ Stability in...

Stabilizing the Y Axis Tensioning with Custom Front Brace and Guide: A Solution for the A8 and A6TensionGuideBraceV2 To ensure proper function and rigidity of the Y axis tensioning, a custom front brace and guide have been created. This bracket...

This part serves as a replacement for two MGN9 blocks, allowing you to connect directly onto existing holes in order to swap out worn-out roller bearings in your Wanhao Z-Axis system.

Slimmed it down a bit and made it to fit with the lower triangle (simple) Z-axis stabilizer brace: https://www.thingiverse.com/thing:4968237 I used the upper part from, but had to get extended screws (M5-0.8 x 12mm):...

Mount the brace with a bearing onto the z-axis sliding rod and screw rod. Move the x-axis near the top before marking holes for the M3 screws. Drill slightly larger holes to make alignment easier. ...Once you've marked the holes, move the x-axis back...

The Wanhao Duplicator i3 Model uses an open-frame design, which allows for easy access and maintenance, making it a great choice for hobbyists and professionals alike. The printer's heated bed is also noteworthy, as it allows users to print with a...

I reworked this design and found it necessary to have roughly 0.4 inches of extra room above the printed part.

Then fully tighten it on the Z extrusion.When installed incorrectly, this bracket could tilt your Z-axis towards the front so it's important to first install it loosely so that it can still move a little and fully tighten all the screws...

... is here to save the day! It was specifically crafted for the Wanhao I3 Duplicator Plus but will also fit other printers with similar-sized spool holders. ...Just swap out the bolts for longer ones and you're good to go, enjoy hassle-free printing!

Here is a replacement for those tiny nuts that secure the spools to the rods on the back of your Wanhao Duplicator 4. You might be pleased to know this modification will likely work with other printers too - because let's face it, those things are...

Attach a small mounting bracket to secure the display cover onto the Z-brace rod of your i3 Duplicator assembly.

... with the Wanhao Duplicator 6. ... Redesigned the original spool holder to be longer, allowing for use of a wider range of spools available on the market. Print Settings: Printer: Wanhao Duplicator 6 Rafts: No Supports: Yes Resolution: 0.25 Infill: 40%

These are the Z-Brace support and rubber feet (if printed in TPU or similar) for morgajel's Z-Brace for Monoprice Maker Select Plus https://www.thingiverse.com/thing:2349318. The feet provide a secure grip and fit seamlessly into the existing holes...

Calibration tool for perfectly aligning the lower x-axis rod with the y-axis rods on Wanhao i3 and Plus, MonoPrice Maker i3 and Plus, and Powerspec i3 and Plus printers. These calibration tools work seamlessly on any Prusa i3 style 3D printers...

It's a straightforward LED strip holder designed specifically for the Wanhao Duplicator I3 v.2. If you'd like to learn more about this enclosure, simply visit my website at http://www.3dsolio.wordpress.com by clicking on it. ... For those who want to...

It's a straightforward LED Strip Bracket designed specifically for the Wanhao Duplicator I3 v2. My Website If you're interested in learning more about this case, visit my site by going to http://www.3dsolio.wordpress.com. ... Support 3D Creator To...

This brace is slightly angled along Y and X axis to clear print head along Z axis. As result it doesn't limit any axis and could be mirrored for dual bracing of the printer. Hardware needed (one side of the printer): Threaded rod M10 570mm ...

Threaded rod is screwed in on both ends. Top mount is just snap fit on top 2020 extrusion. This brace is slightly angled along Y and X axis to clear print head along Z axis. As result it doesn't limit any axis and could be mirrored for dual bracing...

However if you are really serious about removing all slop from your SM you will want to add a top brace across the the two Z-Axis linear rails and another brace from the mid/top of the Z rails down to the baseplate but both of these braces are much...

Other useful links for the rest of my build include: Z-axis cable chain + mounts: https://www.thingiverse.com/thing:3664891 X-axis tensioner + motor mount: https://www.thingiverse.com/thing:3664832 Titan Extruder + Volcano Mount:...

These are the STL files for major enhancements to the Wanhao Duplicator i3, version 2. ... Improvement Design The improvement design was entirely performed using Blender software, specifically version 2.76.

Here is the rewritten text: Connect the cable for your Wanhao Duplicator 6. ...Watch this video to learn how to do it: https://www.youtube.com/watch?v=y8ZgUxTTBWc.

You swap out your Einsy door, which you likely only used once, for a sturdy brace that links the Z axis to the Y axis. This makes the left side of your printer as solid as the right side. You keep the original Einsy base and don't need to disconnect...

I made some slight adjustments to phillica's 3D printer modifications, ensuring their design fits perfectly with the Z pillars on my Wanhao Duplicator i3 Plus.

Originally, I duplicated the nuts provided with the printer almost exactly (refer to source), but decided to create larger versions as well to prevent spools from ever falling off again. Here are its key specifications: Outer diameter measures 55...

This is a straightforward LED Strip Bracket designed specifically for the Wanhao Duplicator I3 v.2. ------------------------ Visit My Website ------------------------ To learn more about this project, check out my website by clicking...

***New smaller thumbscrews for use with v1.5 D7*** A set of replacement thumbscrews designed specifically for Wanhao Duplicator D7 models. These custom thumbscrews were printed directly on my D7 to replace the standard steel units. To install,...

Industrial designers and makers who work with the Wanhao Duplicator 3D printer frequently express frustration when their build platform consistently sinks lower than intended levels after printing or calibration tasks. This persistent issue forces...

Same thing as the original by Brolin Workshop, but with smaller screw holes. Fits M3 screws and washers. Works great with <a href="https://www.prusaprinters.org/prints/45082-pursa-miniprusa-mini-t-nut-for-extrusions-m3-nut-i">these</a> t-nuts which...