wanhao duplicator 4s z axis brace and bushing 3d models

This is a remix of the top Z-Axis mount for the Zonestar P802QR2. To take advantage of common 608zz skate bearings, you'll need 4 count M3 bolts and nuts to replace small screws on the original ones. You can find these at DIY3Dtech.com. If you don't...

And secondly, even if I did use one of their designs, the setup wouldn't work with this Y-axis upgrade I'm planning to install: https://www.thingiverse.com/thing:2836470 This solves both problems by being a drop-in solution; no Y-axis disassembly...

And secondly, even if I did use one of their designs, the setup wouldn't work with this Y-axis upgrade I'm planning to install: https://www.thingiverse.com/thing:2836470 This solves both problems by being a drop-in solution; no Y-axis disassembly...

And secondly, even if I did use one of their designs, the setup wouldn't work with this Y-axis upgrade I'm planning to install: https://www.thingiverse.com/thing:2836470 This solution solves both problems by being a drop-in solution; no Y-axis...

I tweaked the bracket slightly because it was conflicting with the installation of an MGN12H bracket for the Z axis on my D9.

The standard webcam bracket secured two screws on versions v2 and 2.1.

I modified the right rear corner for AzzA's z-brace kit, adding a loop that guides the cable down to the Wanhao Duplicator i3 v2.1's right Z-tower. Two versions of this modification exist: Type 1 and Type 2. The former consists of a simple loop that...

Positioning the Z-axis to 220mm, disabling steppers, and checking for free room before hitting end stops helped me optimize the space. After testing different Z-axis positions, I found that at 230mm, I only had 1mm of free room left before hitting...

To achieve this, remove the X-Axis Linear Bearing and shift the inner Rod Holder to the outer position. The rods will now be long enough to support an expanded X-Axis width of 30mm. ...Next, reposition the Cable Chain Holder and extend the ST2 by adding...

I believe it would be much steadier that way.

... Instructions The models are not adjusted for ABS printing. Scale XY planes by another 1% to adjust for shrinkage. Support and chain elements can be printed from PLA (less problems with warping, slower wear for chain).

Customized version of http://www.thingiverse.com/thing:280974 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=280974

I have upgraded JF_Chabot's design to include not one but two strategic openings for secure belt screw fastening.

... I designed this solution using OnShape. It's part of my project to improve the CTC Prusa i3. You can view and edit the document at https://cad.onshape.com/documents/5e8f73f8fed50f0e62fc5fa6/w/0ca1366970b3a50eaf054108/e/69e6343d4e5ed8ac84fcd08b

Keeping the door open on your Wanhao Duplicator 4S just got easier! This handy device ensures it stays wide open, making printing simpler and safer for you. ...Don't worry; this design should also work seamlessly on your MakerBot Replicator 2x, since...

The z axis lead screw nut support uses SC10LUU linear bearing blocks, standard t8 lead screw mount and the lead screw bearing is a 608 with a shaft collar to hold it from dropping down. The x axis assembly is available to accept either SBR12 or...

... prevents wire catch in the back of the machine from interfering. Modified for Wanhao Duplicator 4s use. ...Instructions I exclusively use PLA and yellow Octave ABS, both yielding optimal results I employed a raft to achieve reliable adhesion.

I tightened my switch, but it didn't quite align with the motor bracket, causing it to malfunction occasionally. To fix this issue, I designed a small spacer to center the switch perfectly with the bracket, ensuring consistent performance every time....

you will need 2x m425 bolts 2x m4 nuts 2x 16mm linear bearings

you will need 2x m425 bolts 2x m4 nuts 2x 16mm linear bearings

I wanted a better Z-Axis End Limit Switch adjustment mechanism and really didn't like the Acrylic Attachment bracket connecting the Z-Axis Threaded Rod to the X-Axis cross rail. The entire weight of the extruder, fang fan, and cross rail hung on 2...

Hi SIRPRINTYMCPRINTERPERSON HERE WITH THE Z BRACE TOPPER BOWDEN TUBE FEEDER FOR THE WANHAO I3/MAKER SELECT/COCOON CREATE!!!! Just take a decent length of 1.8mm inner diameter x 4mm outer diameter bowden tube and insert one end into the extruder...

3) Holes have been added for mounting "whatever design" to hold threaded and smooth rods for the z axis. 4) The press nut has been removed from the z xais, requiring you to thread the two plates together. 5) Mounting holes are now present on the...

Wanhao I3 Maker Select Pi 3B+ Case/Mount (Requires Z-Brace, Elevator Screws) Print Settings: Base: 30% Infill Top: 50% Infill Cover: 50% infill These parts fit together extremely tight, making additional screw holes to secure the cover to the top...

If you installed your Z-Brace mod on your Wanhao, MP Maker Select, or other similar 3D printers, you probably noticed that the gantry feet no longer touch the surface where it sits. These pads fill in the gap to provide extra stability. ... Print...

The MDF-constructed CNC machine features its X and Z axes, which are covered in a layer of carbon epoxy for enhanced durability and precision.

Print facing downwards. ...If printing directly onto the Wanhao 4s, carefully lower the bed or adjust the Z-axis settings to prevent the printer from reaching its maximum Z-travel limit.

swivel blocks and arms snap together.(no screws) you will need to take off the face of your printer(wanhao duplicator 4s) to make holes for mounting the swivel blocks to the front of your printer. (reason for removing the front is the holes are where...

I added this brace to significantly enhance the rigidity of my tower's framework. ...Exceptional print quality.