wanhao duplicator 4s z axis brace and bushing 3d models

This is a shielded stop switch designed specifically for the Monoprice Maker Select and Wanhao Duplicator i3 3D printers, along with several other models. I created this device so you can instantly halt a print job if needed, without risking...

A simple yet effective design upgrade for the Wanhao I3 is now available, showcasing a new, rounded face that edges are more accessible and angled bottom aligns with the control box's bottom edge, making it easier to attach. Additionally, a closed...

The Viper mkIII stands out as a straightforward yet highly effective front-mounted cooling fan duct, specifically designed for the Wanhao I3 plus and its clones. ...To minimize vibrations, it's essential to secure the duct in place using O-rings or...

First two are from the stock cooler and the next two are from my upgrade cooler. The last two pictures show the stock on the left and the upgrade on the right. There's an alternative to the stock metal cooler on the Wanhao i3. It's lined up with the...

Print Settings: Printer: Duplicator i3 Rafts: Yes Supports: Yes Resolution: Your choice Infill: 100% Notes: Because parts of the print are relatively small, I recommend setting the minimum layer time to around 5 seconds and keeping the hot end fan...

the last two pictures the stock is on the left and the upgrade is on the right. here is a pla alternative to the stock metal cooler on the wanhao i3. its lined up with the extruder . ...its lighter and works way better than stock. ( will post comparison...

x_offset = 0 y_offset = -45 z_offset = 3.850

just a simple yet effective face for the wanhao i3. new slightly rounded face edges. angled bottom to line up with the bottom of the control box.. and also included a closed bottom version .(for those that want it closed.) has a nice angle and with...

The new face plate hole is designed as a press-and-twist fit for the lens threads, which was necessary to get a good balance between self-threading the lens on and off without stripping the threads. There wasn't much thread engagement, but it hasn't...

Required parts include: 2x Noctua NF-A4x10 FLX 8x M3 x12mm socket head screw 4x M3 x 6mm socket head screw 8x M3 nut 1x big M3 washer for distributing forces while installing the M3 nuts More information on assembling and installing this...

To assemble the face, follow these instructions: Set your printer to 0.2 layer height and 40% infill, and print one shell. Once printing is complete, grasp the faceplate firmly and push the rearward-facing button from the backside outward until it...

As you may notice from the photos I will share later today, it looks much better than the original component and fits snugly next to the extruder assembly. One of my new units is designed specifically for users who prefer to stick with their 30mm...

... inadequate. ...Drawing inspiration from my trusty Wanhao I3 spool holder, I knew just what needed to be done. ...Printed in a sturdy PLA+, the upgrade was a straightforward affair, achieved with precision at a moderate layer height of 0.2 millimeters.

... I've been using both the Z-Braces and Z-Extensions from Azza for some time now. They did the job needed at hand, but my only problem was that the threaded rod got in the way. The solution was to find some Z-braces that wouldn't attach to the front.

I tweaked the Saber filament guide to make it rock-solid and snuggly nestled against the printer's frame, allowing the entire assembly to sit comfortably on top of it and eliminating any unwanted stress or tension.

This is a set of alignment and modification tools for the Monoprice Ultimate. The tools help you drill the frame and square the 8mm rods. https://www.youtube.com/watch?v=inO_ZdQwrZM Print solid in PETG. ...You might need to use an 8mm reamer on...

These parts are for a reverse bowden setup and a foot for mounting the spool holder at the bottom left side of the gantry. ... https://youtu.be/ax-nGRjBshU

I remixed Saaber filament guide to be more sturdy and closer to the printer frame, in addition the arm sits ON the frame, freeing it from unnecessary strain. Category: 3D Printer Accessories

... approach, so I will share my method in the hope that it might be helpful. My setup features a glass bed, and while the guide focuses on cleaning this particular type of bed, the steps should easily adapt to other types as long as they are spotless.

Before sharing the design online, I tweaked it to match the stock height and enlarged the opening where air flows out, albeit not fully open downward to direct airflow towards the part. As for supports, I speculate that those touching the printer bed...

I used this rear fanduct: https://www.thingiverse.com/thing:1246425 alternatives are: https://www.thingiverse.com/thing:2004629 https://www.thingiverse.com/thing:1090433 Using this cooling setup, you get multiple benefits: - the nozzle stays visible...

This tool holder holds your most used tools like the 5 allen keys, calipers, pliers, scissor, USB SD card reader, feeler gauge and conveniently mounts to the spool holder holes. You will need two M5 screws with ~12mm length, but be careful if...

The holes are a little small and will need to be drilled out for M3 and M4 screws. ... This is the fan I used: http://www.amazon.com/gp/product/B00MJU6JR2?psc=1&redirect=true&ref_=oh_aui_detailpage_o02_s00 The shroud is an adaptation of a design by...

Subscribe to my channels on Thingiverse and YouTube today! This innovative design features a total of eight LEDs, perfectly suited for a 24-volt direct current setup. The power source is cleverly derived from the connection point of the cooling fan...

This is what I bought: https://es.aliexpress.com/item/Trianglelab-Bowden-extrusora-BMG-extrusora-clonado-Btech-Dual-extrusora-para-3d-impresora-de-alto-rendimiento-para/32917029058.html?spm=a2g0s.9042311.0.0.293663c0syTViu The pneumatic fitting is...

To fix this issue, I redrew the design in Fusion 360 as a single solid piece and created a mirrored copy so you can choose which side to print on. You can see from my photo that I also printed the tube section of my 6mm tube (available here:...

... гайки TR8. ... Z_Holder_608_FBG4S Z_Holder_688_FBG4S Фиксаторы вала оси Z для 4S на подшипниках 608 и 688. На 688 - предпочтительней. Винты M4 12-14мм, гайки M4 по 2шт. Модель на 3 отверстия. Я использую только 2. ...Ну и корпус сверлить придется.

Door Mounting Bracket for the Wanhao 4S

Wanhao Duplicator i3 Firmware This firmware is compatible with the original LCD and Melzi board. I had to create a custom thermistor table because the standard board uses 10k pull-up resistors instead of 4.7K, which I'm not entirely confident in. To...

Braced Version of Martin, Pawel & Neil's Wanhao Duplicator 6 - Double Axial Fan Shroud.\nThere are slight variations in clearances on the D6, so I've included thinner mounting spacers for added flexibility.\nWARNING\nI only advise this design if...