weighted companion cube 3d models

i added small gap to bottom of the stand for weight and made a cover for it www.yapmalisin.com Category: Gadgets

Plain flat top made with a recessed hole in the bottom so you can insert pennies to add weight to your bases. Print upside down and no supports or rafts needed. ...Glue in 2 pennies to add weight to your base and help the figures to stand and not tip or...

... weight hanger for the Losi worm axles. ...To attach hanger permanently use epoxy or with hot glue to be able to remove them at a later time. Tungsten weight sizes are .375" diameter by .500" long. Printed on 100% infill. ...Will be about 2 Oz per side

... bottom to stabilize vinyl records. ...As the turntable spins, it gives the illusion that the rings are spinning on top of each other. When printing, I increased the infill from the original model to provide the weight needed to stabilize the record.

Front knuckle to replace the factory unit with previsions for tungsten weights. Steering link will have to be modified, factory link will not work. Tungsten weight sizes are .375" and .250" diameter by .500 long. Printed on 100% infill. ...Tungten will...

The supportive device attaches securely to the phone using Velcro, featuring two interconnected pieces that contain six 5/8-inch washers glued together inside to provide added weight. These specific-sized washers contribute around seven ounces of...

There is a weighted option from which you can add a stop script halfway during the print and add some weights. BEWARE: If you use the none weighted your feeding tube could get stuck. If this happens then just push harder and it will work again. ...

Kururin Rolling Stick Weighted Fidget Toy Tumbler This Kururin rolling stick is engineered to be weighted on the extremes of the fidget toy for enhanced rolling thumbler effect. Print 100% infill rectilinearly The design will form an interior air...

This is so I could weight it with steel shot: https://www.amazon.com/gp/product/B08K538W9P I glued it in and then added some bondo putty to fill it: https://www.amazon.com/gp/product/B0007ZHTTS The cage part is printed separately so that the hollow...

... I wasn't aware they were a slightly different size. I enlarged the internal cavities to allow for the larger penny, and I also extended it so that I could srick more pennies inside for extra weight. ...82 in total filled it and weighted it nicely.

The bottom unscrews so it can be filled with a weighted material so that the stand doesn't tip over, particularly when using it with a heavier pen. ...I use these steel BBs which you can buy $3 for 1500: https://www.amazon.com/gp/product/B000HKKY7C/ ...

<p>just another fidget spinner.. ...;) double wide for 2 bearings, threaded thumb pad to match extra width uses bolts for weights instead of more bearings 2 versions •US 1/4-20 bolts •Metric M6 Print instructionsCategory: Toys &amp; Games

This is a tall headphone stand, that can be printed in multiple parts for small printer. ...The base is hollow in order to be weighted. The parts need to be glued together after printing. ... The model in one piece is also available.

Use dead AA batteries to make weighted chess pieces. After printing, assembling and spray painting, they have a nice feel. Pawns are just batteries with no toppers. ... This is what I will be doing with all of our dead AA batteries from our LED...

... toys boasts two bearings and a threaded thumb pad to match its extra width. Unlike its competitors, this design chooses bolts for added weight instead of additional bearings. ...There are two versions available: • US 1/4-20 bolts • Metric M6

It uses cheap Line-Loc/Snap-Loc clones and alligator clips.As I am fortunate to be able to source free material from my job I decided to make a weighted helping hand base. This one uses two 100x100 mm 3mm thick ‘sheets’ of steel to weigh the whole...

It uses cheap Line-Loc/Snap-Loc clones and alligator clips.As I am fortunate to be able to source free material from my job I decided to make a weighted helping hand base. This one uses two 100x100 mm 3mm thick ‘sheets’ of steel to weigh the whole...

This is a remix of the original Weighted Ball MagSafe Charger Stand (4783199) by jburd which is a fantastic stand but didn't accomodate the iPhone Pro Max very well (especially with its case on). This remix just increases the height of the Weight...

... The bottom and middle sections feature prominent cavities that can be filled with various materials to add substantial weight to the model, enhancing its overall stability (I opted for sand, but feel free to explore alternative options).

... infill structure. Two zero hooks and hardware contribute to its weight of 2.33 ounces or 66 grams. Five-eighths inch openings have been added for attaching eyes. ... Grommet holes have been incorporated into the front, bottom, and tail sections.

... hold a 9.7" iPad 3 in portrait mode, as seen in the pictures. To simplify filling, the previous version has been modified with three holes separated by small chambers, which are filled using lead from a damaged diving weight for precise placement.

The Kururin Rolling Stick Tumbler is a precision-designed fidget toy that expertly combines weighted extremities for enhanced rolling functionality. This expertly crafted toy features a unique design that allows for a 100% infill rectilinear print,...

disable_mholes = False #disable magnet/bolt holes #^includes bolt bore, counter bore and countersink disable_weights = False #disable tire weight cutouts #^DOES NOT REDUCE THICKNESS OF PARTI re-implemented this because it seems like a perfect fit...

... take actions, this die supersedes Action Points as in previous rule editions. Its sides are weighted to favor certain numbers, deviating from the standard 1-10 layout: two sides display 1, two show 3, two show 5, and one each shows 4, 6, and 7.

The Version 3 of the Granby Games full-size weighted keyboard section features a number of key modifications, including changes to the rear mount for key sensors and a reduction in thickness of the rear key sections. This allows for multiple key...

... for the other. If you want weighted dice, select the desired number and choose the corresponding diceX.stl file, then opt for dicecolorweight.stl for the other color. ...Don't forget to use the provided Blender file to print multiple dice at once!

I did print with a brim to prevent any kind of warping.The bottom half can fit about 20 pennies in it, I do recommend filling it to the top for the most weight.Finally, I finished it off with 4 #6 screws, the hole diameter is .16 (in) and I printed...

cube_in_cube_in_cube

-As hidden a seam as possible – I added a lip on the bottom half of the ball for the seam to tuck behind Other components used: -8mm Barrel hinge -6mm x 2mm circular magnets -Button: 16mm rugged LED pushbutton with on/off (or “latching”), I used the...

One notable feature sets this model apart from its competitors: instead of using additional bearings to achieve stability, it relies on bolts for weight distribution. This clever approach ensures smooth and consistent spinning without compromising...