x plus qidi 3d

-Qidi X-Max -Qidi X-Plus ________________________________________________________________________ Since I don't feel like always ordering the PTFE hose from QIDI, I have now designed this easy way to cut your own PTFE hose. With the following...

AboutQIDI X-Max X-Plus I-Mate (S) Wingnut Extender is an extender for the wingnuts that secure the bed leveling screws on the QIDI X-Plus and X-Max. I found the wingnuts to be annoyingly small so you don't get any force to unlock it and it was also...

**MOVED TO PRUSA:** https://www.prusaprinters.org/prints/155501-qidi-x-max-x-plus-internal-filament-guide-v2 This internal filament guide set works with X-Max and possibly the X-Plus. It replaces the simple OEM vertical guide with a 4mm ID X 6mm O.D....

It is a phone mount for the Qidi tech X-max and X-plus. You would need to use attached custom start and end g-codes in Cura (or whichever software that allows them). Otherwise the extruder will hit the mount during initial priming. ...

It is a phone mount for the Qidi tech X-max and X-plus. IMPORTANT: You will need to use attached custom start and end g-codes in Cura (or whichever software that allows them). Otherwise the extruder will hit the mount during initial priming. ...

You will not be able to use the top hat with large spools. The xtensions should sit with a tight fit in the original holders. The mod worked for me as a quick intermediate solution until I finished my piggyback- spool holder. Print Settings Printer:...

There are four parts: Upper Guide, Lower Guide, Lower Guide Standoff, and PTFE Tube connector for BMG type extruders.The setup uses about 1.5 meters of PTFE Teflon tubing 4mm ID X 6mm OD 1.5:...

Print on it's side with support between the feet (as per diagram in "QIDI X-Plus X-Max Ribbon Cable Bracket by humebeam ") Printed in PLA+, has enough flex. Post-printing, just needs sharp edges smoothed. Note: with any back clip, on the X-PLUS,...

After getting frustrated with every adapter and modification I've tried for my Qidi X-Plus, and X-Max, I have tried most of the prints and only found one mod that works (yet motion isn't as smooth as I'd...

I purchased a dial indicator to level my qidi x-plus more easyly and precisely. When I tried the holder from fdunn59 (https://www.thingiverse.com/thing:4633291) I had the problem, that material from the neodym magnets rest on the linear rails and it...

Updated June 2022This carriage fits the Qidi X-Max (X-Plus) where the bearings are 29mm L, 19mm O.D., 10mm I.D.The stock Qidi X-Max carriage it is a pain in the you know what to switch between the low temp to the high temp extruders.This design moves...

Thanks :)https://www.paypal.me/humebeamengineeringAboutThis is a Hygrometer / Thermometer Holder that snaps onto the rear chamber fan cover of the QIDI X-Max and X-Plus. It was requested by one my followers. It might fit other printers as well.BOM -...

This is a Bowden Tube Connector for the QIDI X-Plus and X-Max extruder covers. Just remove the screw from the top cover, place the connector and screw it in place with a 20 mm M3 screw. It is compatible with 6.0 mm PTFE tube, same dimension as the...

Version history3.0:Bracket angled towards extruder cover to keep the cable from dipping down.You may have experienced that over time the cable will dip down using the V1 and V2 brackets, this angled design will prevent that.2.0:Improved version that...

Bob Martin in the Qidi 3D FB group owns an X-Max and says it fits his also, otherwise, there is another pi-cam mount you may want to check out here if you think this one is in the way too much: https://www.thingiverse.com/thing:4347548 I'm using the...

I purchased the Qidi X-Max in December 2021 and these carriages fit models of this period. The bearings are 29mm L, 19mm O.D., 10mm I.D. Probably fits the X-Plus from the same period, but I cannot confirm this. My system was making unsettling...

About Gripen is a high flow fan duct for the QIDI Tech X-Max and X-Plus. In order for you to use it, you need the new extruder carriage. I have attached a picture so you can tell if you have the new carriage or not. If you don't have it installed in...

About Draken is a high flow dual channel fan duct for the QIDI Tech X-Max and X-Plus. In order for you to use it, you need the new extruder carriage. I have attached a picture so you can tell if you have the new carriage or not. If you don't have it...

About This is a support bracket for the Qidi X-Plus and X-Max ribbon cable, it attaches to the top extruder cover. Without support, the cable dips down when it gets extended, causing unnecessary stress on the cable as well as it getting greasy from...

Qidi X-Max (X-Pro) ribbon cables are easy to replace when using these clips to manage the cable. These clips may work on other Qidi printers as well.There are three kinds of clips:Upper back frame railSide corner frame railBottom side frame railAlso...

This is a Hygrometer / Thermometer Holder that snaps onto the rear chamber fan cover of the QIDI X-Max and X-Plus. It was requested by one my followers. It might fit other printers as well.</p><p><strong>BOM - Bill of materials</strong></p><p>You...

This is a recessed cover designed to close the large opening in the Qidi X-Max & X-Plus printer top covers, allowing for filament spools to be accommodated without excessive pressure. Additionally, I created a 30mm to 50mm spool insert that helps...

I just recently converted my Qidi X-Plus over to a Lerdge K setup like my X-Pro. I wanted to keep the FFC ribbon cable setup but add the auto leveling functionality now available to me. I tinkered with several addon mounts but none of them seemed...

About This is a filament cleaner and backspin preventer for the QIDI X-Plus and X-Max. It was originally designed for one of my other designs but I never included it there. To use, print the two parts. Cut a piece of sponge and place it inside the...

I changed the title and tags to include "X-Plus" because I think this may work for that printer as well. If someone that owns one could check things out and let us know, that would be awesome; I'll take the bait out of the title if it turns out not...

AboutThis is a filament cleaner and backspin preventer for the QIDI X-Plus and X-Max. It was originally designed for one of my other designs but I never included it there. It should fit all printers using a 6 mm bowden tube as well.</p><p>To use,...

AboutThe Adjustable Spool Holder for QIDI X-Plus and X-Max works with most filament spools up to 1 Kg. It uses common 608 roller bearings (search for 608ZZ or 608RS, I bought 4 for €4) for a smooth rotation of the filament spool. The spool holder is...

The files added are: external-rod-holder-left-tall-1.0.stl external-rod-holder-right-tall-1.0.stl About The Adjustable Spool Holder for QIDI X-Plus and X-Max works with most filament spools up to 1 Kg. It uses common 608 roller bearings (search for...

To upgrade, you only have to reprint this part, the other parts are unchanged: qidi-xplus-xmax-extruder-fan-duct-404020-part-2-ribbon-cable-holder-1.1.stl About This is an alternative to my QIDI X-Plus X-Max Advanced Extruder Cover:...

About This is an advanced Extruder Cover for the QIDI X-Plus and X-Max. The original cover didn't have much space for a larger fan (although a 40 mm fan just about fits) and was lacking a few other features. The cover has the following features:...