x tension 3d models

This a tension device applied with all 20 aluminum profile by belt.

zonestar p802n p802na simple X tension

I discovered a crack in my original x-tension housing, so I decided to make a new one, but based on the original tension system of the ender 3 v2. I also made it thicker and more robust then the original. If you need a longer version for "longer"...

I discovered a crack in my original x-tension housing, so I decided to make a new one, but based on the original tension system of the ender 3 v2.I also made it thicker and more robust then the original.If you need a longer version for "longer"...

Sawaguna modified the CR-10 Mod - X axis Tensioner by Comely_Cool to make it compatible with the Eryone Thinker series. I have an Eryone thinker SE and found that the Sawaguna's mod would have required longer M4 bolts to drive through the 2020...

in the original design, witch the rods where only stucked in, was most of the tension directed over the z-bearings, z-rods and frame. this presses directly onto the x-rods, witch have a blind-hole on the other end. 'connectet by shape' rather...

This is a remix of superpotatofudge's EXCELLENT HOTAS extender: https://www.thingiverse.com/thing:3629842 I wanted to make a longer version of this because while his button box is cool, it only puts about 5 inches or so of space between the...

Belt-Tensioner for printer with 20 x 20 al-profiles in the x-axis. Printed with 0.2mm-layers with overall-supports and support-interface. ...

Allows for tensioning of the x axis, without having to unfasten the timing belt. ...I have uploaded a few different lengths to support different X carriages.

X belt tensioner short plate

Easy to print - Anet A8 X Tensioner. ... Ustawienia wydruku: Fill density - 100%

... was extended and a "shelf" added to trigger the x endstop. Use all the other parts from the original and have a nice new x tensioner on you Anycubic Mega Zero update: turns out the screw doesn't like the factory bearings...modified that as well

This is the body only for an X-Tensioner made by Cornely_Cool (Thanks!). I needed this to be shorter at the top to fit my new 3D printer build with linear rail and dual Z mods. The nut and knob will still fit according to the original build. ...Pictures...

CR-X belt tension bracket for Y-axis

I made this as a fun project to improve the x-tensioner. The bearing housing broke a couple times and the main bracket bent over time on the original, so I added some material to prevent that from happening. Also, the x belt was rubbing on the 2020...

This is the original X Tensioner design. Recommend you go to the new improved design with stouter bracing and a thicker pulley. https://www.thingiverse.com/thing:3625832 This is a design by Karl from the Adimlab Facebook page. When I made mine...

Simple add on x-tensioner. The I3 does not have a way to adjust the tension on the x belt. Other tensioners require replacing parts but this one simply slides into place in just a few minutes. Instructions I noticed that the x axis rods were fixed...

This is the original X Tensioner design. Recommend you go to the new improved design with stouter bracing and a thicker pulley. <a href="https://www.thingiverse.com/thing:3625832">https://www.thingiverse.com/thing:3625832</a></p> <p>This is a design...

Use this tool to help adjust your X belt tension. Simply loosen your X motor screws, slide the tool over the bottom of the motor and adjust the thumb screws until the desired tension has been achieved. ...Tighten your motor screws and remove the tool.

this is the x carriage tension adjuster mod for the newer eleksmaker lasers with the open build wheels. It requires you to use the 2 M5 bolts and nuts that came with the machine at the pivot. At the top corner you need two m3 bolts. At the...

... you will have to cut the belt about 2cm. This solution will eliminate ugle tie-rap- X axis tension for the kingroon kp3s. you need 3 screws 4mm and 2 nuts 4mm. you also need a new printer belt. 5cm longer. ... this can be printer in pla or petg.

Use this tool to help adjust your X belt tension. Simply loosen your X motor screws, slide the tool over the bottom of the motor and adjust the thumb screws until the desired tension has been achieved. Tighten your motor screws and remove the tool. ...

This is the x carriage tension adjuster mod for the newer eleksmaker lasers with the open build wheels. It is a redesign of the model remixed by nottingham82, and is just cleaner with rounded corners, inserts for the m3 nut and bolt, and a...

this is the x carriage tension adjuster mod for the newer eleksmaker lasers with the open build wheels. It requires you to use the 2 M5 bolts and nuts that came with the machine at the pivot. At the top corner you need two m3 bolts. ...At the tipy top...

Just as @p45q, I discovered a crack in my original x-tension housing. I decided to remix his project, but make it look like ender 3 S1. I used PLA, 30% infill, and 0.2 layer height. I think it's best to print it vertically Check out my...

The stock idler bearing is too large for the original X belt tensioner arm, so I did a quick mod so that it works with the stock bearing that comes with Tronxy P802E. I then modified this Z Stop mount linked here,...

This is to allow tension to be pulled on the X axis belt. Tight belt, tight prints. ...I used this for the x belt holder: http://www.thingiverse.com/thing:1666094

my x rods stick out slightly so i printed the x tensioner with holes and I didn't like how my z rods flex under tension. ...This backplate allows for a the x rods to protrude slightly but keep the tension on the x rods.

This is a X tensioner for Tevo Tarantula. ...The only thing needed is: -1 M3 nut -1 M3 screw Updated: if you want to add a wire chain you should better download this one: https://www.thingiverse.com/thing:2829404 enjoy!

This is a X tensioner for Tevo Tarantula. The only thing needed is: -1 M3 nut -1 M3 screw Updated: if you want to add a wire chain you should better download this one: https://www.thingiverse.com/thing:2829404 enjoy! ...