xbee interface board 3d models
89788 3d models found related to xbee interface board.
thingiverse
This is a case for the XBee Interface Board (XBIB). It should work with the version that has the two sets of LEDs, barrel connector for power, and USB Type B port on one side (XBIB-U-DEV, XBIB-U-SS). There are five total standoffs beneath the board...
grabcad
This is a model of a board that combines the Arduino Nano with the XBee Module. ... Part number: Gravitech - XBEE-4NANO
thingiverse
This was designed to hold an XBee module on the Parallax USB adapter board, specifically items 247 and 968 from Adafruit. ...It should fit other XBee modules as well.
thingiverse
This is a case I created for the Xbee Grove development board. I am using it only as a Zigbee gateway/router, so it is sitting behind a couch. ... I wanted to make sure it was protected.
thingiverse
Then slip the connector on the XBee breakout board into the header and clip the board into the holder. With everything held firmly in place, solder the header and link wires to the prototyping board. ... Finally, recheck your wiring, then fit the XBee...
grabcad
Interface board for probe card analyzer (PRVX) use to test probe card
grabcad
This is just the basic shape of an Xbee Radio modulal. ...The model is based on measurements taken from an Xbee S2 Pro,
thingiverse
I tested it specifically with an XBee Cellular Verizon LTE Cat 1 dev kit I had (XKC-V1T-U, https://www.digikey.com/short/jm2npj), but any kit using the same revision of the XBIB dev board and antennas should work fine. There are holes in the case...
grabcad
NI 4axis Motion Board(73XX) Interface Terminal 1. TTL -> Line-Driver 2. ...Line-Driver-> TTL
thingiverse
The Interface Board is a PC-free controller for your MakerBot Replicator. When hooked up to the Replicator's MightyBoard, the interface controller can be used to jog the printhead, run calibration scripts, initialize and monitor prints, and more!
thingiverse
This is a case and mounting plate for the 60 x 60 board used in this project https://github.com/jaymzx/RPi-WD-Packet-Interface The case has mounting plate for a 75 x 75 Vesa as used on the SmartiPi case. The model includes mounting holes for a Pi2/3...
thingiverse
Daly Parallel Adapter Board offers RS485,RS232 and CAN support but no enclosure. For that i measure it out and reverse engineer it with fusion360. ...
thingiverse
... in my smart home Hubitat Elevation setup. ArstenA did a great design for the base, but I needed other options with the different Xbee boards I was using. ...I also needed to mount a few of them to walls, so I remixed the base to have mounting tabs.
thingiverse
This is a housing for the spark fun xbee carrier (the one with a mini usb connector) and an xbee module (one with an external antenna). There is a version with and without a hook to hang it from your laptop screen (it's sized for a macbook pro but...
pinshape
SummaryThis is a housing for the spark fun xbee carrier (the one with a mini usb connector) and an xbee module (one with an external antenna). There is a version with and without a hook to hang it from your laptop screen (it's sized for a macbook pro...
thingiverse
http://hivetool.org/w/index.php?title=Hardware:_Hive_Interface_Board When soldering the board, leave the LED leads long where it can come up through the hole in the top. To compile the SCAD files put the required STL from the original "Raspberry...
thingiverse
Protect pins (if soldered on) from desk/workbench stuff. Instructions Print, screw and use. I used 4-40 and a 3/32" drill bit seemed to be just right. the holes are left small so you can use hardware...