y axis 3d models

I went all crazy about my Prusa MINI catching fine dust and filament pieces into Y axis grooves, so here is my solution. Click-in extrusion covers!Fast to print, even faster to click and bye, bye dust!Designed especially for Prusa MINI, but will...

Returning to the stock tensioner resolved issues with Y-axis layer shifting caused by the broken mount. I'm leaving this here for anyone who might still find it useful, but there are superior designs available. Removing top mounting screws and...

This is a rework of the Y axis for the Wilson 2 to make it significantly more robust. Due to the plastic ends used on the Wilson 2, any belt tension causes the motor mount to warp downward, which could lead to backlash and eventual part failure. So I...

I decided to relocate the stepper motor and adjust the belt plane to eliminate a dangerous setup that put wiring too close to the pulley and drive belt on my Y-axis. To retain print bed height, I replaced the original bearing setup in the new...

... kept the belts parallel to the extruder, ensuring smooth operation. It's worth noting that on the right side (X axis), the spacer is located at the front of the printer. On the left side (Y axis), however, the spacer is situated at the rear side.

Situation: Force applied by the motor onto the bed plate left bearing when reaching the end stop makes an undesired momentum, causing after days of print, play into the bearings and plate support.Remedy: Adding an end stop on the Y right shaft at the...

This Is a Y Axis Belt Tensioner designed specifically for the CR-10S printer, measuring 500 x 500 x 500 dimensions. Frustrated by fitment and function issues with other y belt tensions, one resulting in a catastrophic structural failure during...

I didn't like the Y-axis belt tensioner's design in the original. Fitting the details was tough and it seemed flimsy to me. Yes, I know there are designs in the remixes with handles and one tensioning bolt that won't push into a plastic part. That's...

For reference the dimension between the Y axis rod and 3030 profile is roughly 35mm - some tolerance is allowed for in the 10mm cable chain ends. Ideal for Omnomnomagon's Reduplicator project - hides the heatbed power and thermistor really nicely....

It retains the socket head cap screw as the Y end stop. I designed this after my Y axis belt disintegrated, which was a fun issue. It doesn't add a tensioning mechanism, but it does make it much easier to swap the belt, as well as hopefully relieve...

These are replacement brackets for the 8mm linear rod used on the Y axis of the Anet E10, E12, and E16. They are open ended which allows you to use longer linear rods if needed. I have 500mm rods on mine and they sit flush on the front and back of...

2GT belt clamps for the Y-axis, Fits to replace the standard holder. In two sizes, one for neoprene with fiberglass core and for PU (polyurethane) with steel mesh. With opening for pushing out the M3 nut and for 2GT strap itself. With the size of...

This is a replacement bracket for the Y-axis pulley on the Wanhao Duplicator i3 and clones. The stock bracket can flex during print, causing wavy lines on the print surface and added noise. This design is based on Amkza's but has been modified to...

I'm planning to utilize 12mm rods with bushings for my Y axis assembly. The rod mounts are currently under development and are undergoing fine-tuning adjustments. I've incorporated the 1.1 "Small Hole" files, which allow for a 12.25mm rod hole in...

With this stronger Y axis made of Threaded rod this is no longer the case. It also helps eliminate vibrations. 4x pieces of 7 1/4" long 8mm or 5/16" diameter threaded rod are needed. 20 Nuts that match the fit of your 7 1/4" long threaded rod must...

This setup is tailored for the AIO, but xyz's design of the Y-axis harness leaves zero wiggle room, resulting in a nasty bind on the wires that causes them to snap from within their sheath right where the tie-downs are located. If this has already...

This a remix of the jfromel Y Axis Linear Rail and Belt System https://www.prusaprinters.org/cs/prints/23893-y-axis-linear-rail-and-belt-system It is a nice idea so I have made it. It works much better than the original MK3 Y axis system. The...

About ===== This upgrade aims to boost the stiffness of the AM8 Y Axis, ensuring compatibility with AM8 while increasing Y stiffness, particularly when utilizing longer Y rods for a 300x200 bed. My Y rods measure 480mm in length. I'm pairing these...

Extend your y-axis to 150mm! All you need is two 8mm 10" rods and a longer GT2 belt, both of which can be found on eBay for less than $20 total. This idea was inspired by nucgloworm's model. This cannot be printed on the Printrbot Play since the...

Open Cable Chain link from thing:611593 for the Y axis that fits on the Geeetech Prusa i3 Pro B's M10 threaded rod. You can adjust most distances and sizes in the SCAD file. Print Settings Printer Brand: RepRap Printer: Geeetech Prusa i3 Pro B...

---- When I ordered my Ender 5 Pro, it came in with a bent Y axis belt bracket. Upon doing research, I found that this is a common problem, unfortunately. I was told to bend the metal bracket back straight, which I did, but it wasn't as good as...

It was making my Y axis all weird and people have told me to try rails, so I did! It's prints up easy and installs easy too. See the pictures for an idea how. You'll need M3x20 bolts and nuts x 8 and M4x10 bolts and nuts x 16 plus the M5x8 and...

Although it may not make much of a difference, it looks great and might lend some extra stability to the Y axis. Note that it doesn't touch whatever surface your printer rests on; instead, it is intended to clamp onto the Anet frame via the nuts and...

This is a Y Axis End Stop for the "Original" Prusa i3 designed by Prusa Research. The kit enables you to secure the switch to the 8mm round bar using a more robust method than zip ties, thereby eliminating any potential damage from excessive...

I've been hunting for a y-axis tensioner that looks like it would be stock, but haven't found anything not insanely over-engineered.Like always, I finally landed on one I liked enough to remix. This time, it's from Thingiverse: <a...

The new shaft drive perfectly aligns and supports the Y axis shaft. This critical alignment ensures that every step of the assembly process is precise and secure. By incorporating this feature, you can confidently verify that the system is properly...

####GIRO - Dual Y-Axis Bracket#### ####General#### This design was influenced by [colindo]'s original concept, but I felt it needed improvement to achieve optimal stiffness. I decided to remix and redesign the bracket to address these concerns. The...

Basic Y Axis Belt Tensioner: Fine-Tune for a Smooth Ride Depending on the print quality, post-print work may be necessary to achieve a smooth action. In my case, the print turned out perfectly with these settings, but you might need to adjust the...

This is a replacement Y Axis Bearing Rod support for Prusa i3 Aluminum extrusion printers. It improves over stock versions by having a ridge that tightly aligns with the aluminum extrusion and having a bearing rod clamping feature. There are right...

As a result, the y-axis motor no longer takes the brunt of the impact.\r\n\r\nThis custom spacer sits snugly between the SCS8UU housings and the bed itself, providing a much-needed buffer zone. It's an essential component that keeps everything...