y6 hexacopter 3d models
571 3d models found related to y6 hexacopter.thingiverse
Introducing my first iteration of a Y6 hexacopter, which was inspired by the RCexplorer tricopter, Flitetest anycopter, and 3D Robotics Y6. The majority of parts are laser-cut, while some 3cm and 1cm spacers were printed where necessary. ...For more...
thingiverse
Part for the Yupiter Y6 hexacopter https://rotorbuilds.com/build/10722 Overview The Yupiter is a mid range craft intended to be smooth, reliable and... exquisite. Let's talk numbers. 6 motors, 3 arms, up to 7" propellers, 6s battery, 10+ minutes,...
grabcad
A Hexacopter, specifically referred to as the Y6 model, is an unmanned aerial vehicle featuring six rotors for lift and stabilization. ...This innovative design allows for increased stability and maneuverability compared to traditional quadcopters or...
thingiverse
Discover the entire T copter family including the TX8 Octocopter, T6 Hexacopter, T4 Quadcopter (10" props), T4 Quadcopter Mini 315 (7-8" props), T4 Quadcopter Mini 250 (5" props), and Tubular Crossfire 2 quadcopter. A post discussing and enhancing...
cgtrader
SummaryA Y6 hexacopter I designed and lasercut. First IterationInstructionsIt was inspired the RCexplorer tricopter, Flitetest anycopter, and the 3D Robotics Y6. The majoritgy of the parts are laser cut, but I ended up printing some 3cm and 1cm...
thingiverse
http://www.thingiverse.com/thing:1299137 - Full 3D Print Y6 HexaCopter Flame V3) Some video:https://youtu.be/pb2V_UGtkoM Print Settings Rafts: Doesn't Matter Supports: No Resolution: layer 0.25mm Infill: 100% Notes: Parts x Number of print (Infill):...
thingiverse
The Y6 motor mount, a prototype derived from http://www.thingiverse.com/thing:11604, features a dual motor design with increased mount platforms for extra clearance. Turnigy motors, with their elongated shafts, benefit greatly from the added...
thingiverse
Camera Mount for Full 3D Print Y6 HexaCopter Flame
thingiverse
LED mount for Full 3D Print Y6 HexaCopter Flame Flame:http://www.thingiverse.com/thing:1046175
thingiverse
As subject, GPS Mount for Full 3D Print Y6 HexaCopter Flame (v2) For Flames:http://www.thingiverse.com/thing:1046175http://www.thingiverse.com/thing:1001202
thingiverse
As subject, Gimbal Mount for Full 3D Print Y6 HexaCopter Flame (v2) Flame:http://www.thingiverse.com/thing:1046175http://www.thingiverse.com/thing:1001202
thingiverse
A rapid and unrefined modification for my ArduCopter Hexacopter features a prototype Y6 Landing Gear Leg inspired by http://www.thingiverse.com/thing:9813. This is currently insufficiently robust to handle rough landings, merely supporting the Y6 off...
thingiverse
HexaCopter Y6 330MM I hear that Y6 may better that Hexa. It can use bigger propeller and foldable arms. So I try to design this flame. Main Features: Full 3D print part. ... Foldable arms RECOMMENDED CONFIGURATIONS: 6" ~ 7" propellers 2206 ~ 2208...
thingiverse
HexaCopter Y6 380MM (Version 2) The is version 2 with improved ARM and MainFlame. Main Features: Full 3D print part. Foldable arms Version 1: http://www.thingiverse.com/thing:1001202 Print Settings Rafts: Doesn't Matter ...
thingiverse
Y6 Rack third generation New design ARM locker Because above point 1 improvements, wire can through inside the arms New 3DR Y6 style landing gear Merger battery panels & lower layers center plates Vibration damping motor mounts Foldable GPS holder...
thingiverse
Anti Vibration Mount for Full 3D Print Y6 HexaCopter Flame Vibration in PIX/APM cause strange behavior for my Y6. So i design this anti- vibration to see if the problem can be fixed. ...Flame:http://www.thingiverse.com/thing:1046175
thingiverse
This is enhanced ARM to make sure it is strong enough to handle 450 Y6 Flame Flame:http://www.thingiverse.com/thing:1046175
thingiverse
Mount Feiyu Tech FY MiNi3D 3 Axis Gimbal to Full 3D Print Y6 HexaCopter Flame V3
thingiverse
Flame:http://www.thingiverse.com/thing:1046175 https://youtu.be/zh8ArzIEKKg
thingiverse
Original design is great, but my motor cables are too short. Also, it was really hard to fit plush ESC on such short space between cable openings. So I've moved top opening closer to the motor which fixed both of my problems. ...I am not sure yet if it...
thingiverse
Small conversion plate, to fit ardupilot controller on the top plate.
thingiverse
Enhanced ARM Flame:http://www.thingiverse.com/thing:1046175 Print Settings Rafts: Doesn't Matter Supports: ...
thingiverse
To mound round ws2812b x16 LED under the motors. ...Flame:http://www.thingiverse.com/thing:1299137 Example Movie:https://youtu.be/YKy_UaBvD-Uhttps://youtu.be/peAPkQYNOpI
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=931685 Hello This is a very early version of my Y6 hexacopter based on the multicopter frame inspired by Benedikt Haak's dream catcher quadcopter frame. How I Designed This Frame ...
thingiverse
Experience flying a Hexacopter by using OpenPilot.org CopterControl! The provided Sketchup source file will help you recreate this unique design, although it may require some creative problem-solving due to slightly small screw holes. It features a...
thingiverse
Decided to do a remix from HexaCopter (HEX6) version for Mini Flame Wheel since I wanted to create a frame for Y4 or Y6 configuration. I'm using stacked arms and there is just enough space for the motor bolts. ... As I'm used to carbon fiber miniquad...