yet another machine vise 3d models

This is my modified version of Yet ANOTHER Machine Vise by TheGoofy, which is awesome to begin with. ...I had problem with flexible sliding jaw plate staying in place with original design, and since Chris shared the Fusion 360 project, it was very easy...

Summary This is a quite robust 3d-printable machine vise. It's 100% 3d-printed - no screw or other piece of hardware is needed to hold the individual pieces together. Pieces clip and snap together. It's a demonstration that it is very important to...

This is a quite robust 3d-printable machine vise. It's 100% 3d-printed - no screw or other piece of hardware is needed to hold the individual pieces together. Pieces clip and snap together. It's a demonstration that it is very important to consider...

Handle for [Yet ANOTHER Machine Vise](https://www.thingiverse.com/thing:2064269) by [TheGoofy](https://www.thingiverse.com/thegoofy/designs) that is longer to remove interference with the threaded rods and has a grip that provides more torque. Also...

I made another sliding jaw that has a lot more support for the threaded columns (internally and externally). Instead of 90 degree intersections on the outside of the columns you have rounded sections. Internally is just a basic fill. ... This will...

You will need parts also from https://www.thingiverse.com/thing:2064269: - Vise_Main_Gear - Vise_Base_Clip - Vise_Sliding_Jaw_Plate - Vise_Sliding_Jaw - Vise_Sliding_Jaw, you can use also the https://www.thingiverse.com/thing:2123529 And from...

I was printing the wonderful model of this vise (http://www.thingiverse.com/thing:2064269) and had problems by inserting the clips. I had to make the clips 0,3 to 0,5mm smaller that it fit into my printed vise. Maybe somebody else also needs smaller...

... it easily. Rest of the parts are availaible in the source ;) NOTE: Add screws before assembling whole vise - otherwise you wouldn't be able to slide it later. ... You will additionaly need: -> M4x20 screws - 4 pcs -> M4 square nuts - 4 pcs

... Machine Vise". ...Quickly adjust the vise with a drill.Requires:https://www.prusaprinters.org/prints/14496-yet-another-machine-vise-v2Assembly:Apply CA glue to the inside cavity of the adjustment knob. ...Then press in the hex adapter.</li></ul>

Drill speed adapter for the infamous Yet ANOTHER Machine Vise https://www.thingiverse.com/thing:2064269 . ... Print this with all the small pegs on the build plate with supports.

Drill speed adapter for the infamous Yet ANOTHER Machine Vise Print instructionsDrill speed adapter for the infamous Yet ANOTHER Machine Vise https://www.thingiverse.com/thing:2064269 . ...Print this with all the small pegs on the build plate with...

I made @TheGoofy's "Yet ANOTHER Machine Vise", but those who have been following my other creations know that I am LAZY. I created an adapter that fits into the hollow vise handle, and provides a bit for connecting a power drill. Now, you can use a...

I made @TheGoofy's "Yet ANOTHER Machine Vise", but those who have been following my other creations know that I amLAZY. I created an adapter that fits into the hollow vise handle, and provides a bit for connecting a power drill. Now, you can use a...

All credits to TheGoofy for the original design. I just made it a little bigger so I could use it with larger pcbs with bigger components. ... I had to trim a bit on both ends of the base and print it in a 45º orientation so it would fit my 200x200...

Found and started printing this brilliant Machine Vise from https://www.thingiverse.com/TheGoofy . Then looked at remixes and liked the knurled handle from johann517 and the electric drive socket from philxing so I combined them. I also increased the...

just a quick full plate for lazy printer folks :) ~ 160x180x120mm required (WxDxH)

<p>This is a remix of <a href="https://www.thingiverse.com/thing:2064269">https://www.thingiverse.com/thing:2064269</a> thanks to <a href="https://www.thingiverse.com/thegoofy/designs">https://www.thingiverse.com/thegoofy/designs</a> for the original...

Here are two elements to add the bending function to your vice. ... They adapt to the jaws by clipping on very easily

Widened and added holes for M5 screws and washers to bolt to the table of an Xcarve. Print the exact same way TheGoofy Recommends still not support required. Bolt hole spacing is 75mm to the center. ...Thanks TheGoofy for such a great design.

Modified handle that can be turned with an electric drill/driver with a 1/4 inch or 6mm hex bit. ...Can also use any bit such as a Phillips head if enough of the base of the bit is exposed.

These jaws for the Yet ANOTHER Machine Vise turns it into a pin vise which allows firmly holding odd shaped objects. ... The jaws have threaded holes for M4 x 20 cap screws and optional V groove caps allow better vertical clamping on some objects.

NO SUPPORTS REQUIRED Using 3d print guide from TheGoofy's "Yet ANOTHER Machine Vise" and inspired by philbarrenger's "Monster Mouth Headphone Holder" ending up with this completely different 4 part solution. 3 body sizes available for shelf/desk...

I made this as an extension to the handle on the "Yet ANOTHER Machine Vise" to avoid hitting the threads and added a bar for increased leverage. ...It should slide right onto the handle of the Vise.

I edited the knob from Yet ANOTHER Machine Vise to be a little longer, thinner, and knurled. I got the knurled knob idea from https://www.thingiverse.com/thing:2286789/files. ...I think it is a little easier to use.

I added holes to be able to put 6mm rods through the vise and be able to clamp it down without changing to much of the original design and printability. Based on philxings idea to be able to drive the vise using an electric driver I made my own...

This is just a small modification of the great vise called Yet ANOTHER Machine Vise made by TheGoofy. ...Print Settings Printer: BQ Hephestos 2 ...

A vending machine from a picture found on some image search.

Well, this is my intent of making a derivative of a very cool drawing machine (Axidraw). Coincidentally It was developed at the same time that http://www.thingiverse.com/thing:1444216, but I could not spend enough time to get it done (not a...

###This is a remix of [Yet ANOTHER Machine Vise by TheGoofy](https://www.thingiverse.com/thing:2064269), to be used as base for [LiftPod](https://www.thingiverse.com/thing:4614448). ###Modifications: - 3 slots for M5 nuts on one end. Allows to...

Summary This is a variation of my OTHER Machine vise. Modified base halves for Nema 14 mount. Includes also a modified Center Gear. The remaining parts (sliding jaw, jaw plates, threaded rods, threaded gears, pins) are from the original vise. It also...