zip line pulley 3d models

TMNT - Teenage Mutant Ninja Turtles - Zip Line back pulley My son broke the rubber strap for the back pack style pulley. I made a new one and used zip ties instead. ...Then used a lighter to make sure the zip ties were not sharp.

TMNT - Teenage Mutant Ninja Turtles - Zip Line back pulley My son broke the rubber strap for the back pack style pulley. I made a new one and used zip ties instead. ...Then used a lighter to make sure the zip ties were not sharp.

smal project of testen a 3D printen pulley. ...up to 300 kG,

This zip wire pulley was tested by person with 100kg and it worked fine, so it should be safe for kids. (keep safe height anyway.) It's made to fit about 12mm rope. Pulley is made to fit ball bearing with internal diameter 15mm so you can use...

Zip Line Trollery

Simple Zip Line Trolley I made in ST6. This my first official model, so pardon my professionalism if you notice it :). Please send me tips/suggestions if you have any. ...I am still learning.

Childhood memories of fishing line and zip lines. One of my favorite accessories of the whole line for play value. I know nostalgia isn't what it used to be, but for old times sake may it bring you a smile. At 100% this fits G.I. JOE Classified...

This is a zip line system for Hot Wheels toy cars. In addition to the printed files 2 0.5x20tpi bolts, a 0.5x20tpi tap, and 2 1/16in pins are needed to complete the system. The holes in the clamps need to be tapped and the 1/16in pins are used to...

i had an idea to make my own Radio Controlled Camera dolly for a Zip Line. those things are used on commercial movies were it is not possible to install tracks on the ground for a camera. i didnt know until later that a company made them and sold...

i had an idea to make my own Radio Controlled Camera dolly for a Zip Line. those things are used on commercial movies were it is not possible to install tracks on the ground for a camera. i didnt know until later that a company made them and sold...

Pulley used to raise/lower the washing line for my vertically challenged wife

this is a pulley made for a kayak trolley anchor line i printed last year in ABS is works perfectly may need to invert parts to print without supports

It was a fun learning project to help create something that we didn't have (we bought our tower used and didn't come with the zip line clips). I'm not sure how the "real" clips worked, but these worked pretty well for my 5/6 yr olds. PLA. No...

I didn't like not having a zip tie cable clamp on my bear that is 90 degrees to the one included in the bear files, so i made one.

Print Settings Printer: Maker Select V2 Rafts: No Supports: Yes Resolution: 0.2mm Infill: 35% Post-Printing Instructions Run a zip-tie through from the bottom of the interior side and loop it over and back around. I had originally planned to make...

J'ai eu besoin de pouvoir rentrer et sortir des vélos d'un abri faisant 1m50 de hauteur. J'ai donc fait une tyrolienne à vélo avec un fer plat en acier (40x8mm) et un crochet qui vient se poser dessus pour emmener/sortir le vélo. Imprimé en PETG...

tower of zipline, where could we go, it can be used as an industrial tower aswell

for fun and training

... and pulley nodes small. The intended layout must be flatter and have relative little tension/weight in it's end running state. I'm making an instructable to support this design https://www.instructables.com/id/Halloween-Zip-Line-HZL-Axworthy-Ghost

V-Slot zip tie anchor for in-line cables

I put the zip line just at a child's height (less than 1m50) so that he has to bend his legs to avoid touching the ground. tested ok with under 20 kg kids. tested also with my 75 kg but I just didn't slide. customized from...

YKK Zip

This is a replacement zip toggle designed to any medium to large zip loops where the metal/plastic toggle has broken off.

Mountable One Wheel pulley wheel holder

INSTRUCTIONS ON HOW TO SETUP Tie a piece of Mono filament line (fishing string) from one handle to another by going through the ZeroG Ball. Repeat the process on the other 2 handles.  Notes-  1. I made the string about 10 feet long...

Replacement line pulley, M2-M8 (Logosol saw frame). ...<strong>SKU: </strong>4507-001-0300.&nbsp;</p>

I want to use the fishing line setup from my Rostock Delta Robot instead of a tooth belt. These are the two pulleys. one with a 8mm hole for the axis' and one with a 5mm hole for the stepper. Feel free to ask any question. ...

This kit contains models of clamp parts and handle to create a rope track (Zip Line, Aerial line) suitable for TrixTrux toy cars.&nbsp;You may use handles and clamps in any combination to make rope track in multiple combinations. It is possible to...

This kit contains models of clamp parts and handle to create a rope track (Zip Line, Aerial line) suitable for TrixTrux toy cars. You may use handles and clamps in any combination to make rope track in multiple combinations. It is possible to use...

This is a modification of a ball chain pulley, and a part to attach rolls of pennies (or other weights) to a ball chain for use as part of a Polargraph drawbot: polargraph.co.uk/ The Ball-Chain Pulley wheels are modified from "Parametric Ball Pulley"...