anycubic i3 mega parts 3d models

Hotend cover parts for the AnyCubic i3 Mega with big fan inlets. ... Attention: The right cover must be mirrored!

Another collection of hotend parts for an E3D-v6 hotend

Anycubic I3 Mega part cooling fan duct for a Sunon MF50151VX-B00U-A99 (or MF5015V1). It's not really a remix, but the design is based on [this](https://www.thingiverse.com/thing:3553164) and [this](https://www.thingiverse.com/thing:3340414) fan....

This replaces the cooling fan holder for the AnyCubic i3 Mega. The original fan holder restricted air flow, had a poor excuse for a fan guide, and made a whistle that could drive you insane. Even though this is the first upload of this part, it is...

If you changed to Trinamic 2208 stepper motor driver and replaced the all noisy fans of Anycubic i3 Mega, only thing you can hear is the blower fan noise because nobody makes a quiet blower. This upgrade will enable you to replace it with a silent...

2 of 3 parts with increased clearance for M3 screws and nuts. ... The 3rd part is to complex to generate a solid from the .stl file for editing. ...I asked the original author for the "source" files, but he didn't answer yet.

This is designed to work with my modular X carriage design. ... 5015 blower Inspired by: https://www.thingiverse.com/thing:2004629

First I'd like to thank icecap for the great work! This is the original Hotend Mod: https://www.thingiverse.com/thing:2635522 I just added support for a 80mm LED ring to the silent fan duct. ... I used this one as LED ring:...

Remix of cooler

- A fairly extensive hack-job. This kind of fan does not blow evenly, rather they tend to blow in the direction of blade rotation, so mounting this fan horizontally not only makes it likely something will fall into the inlet, but it also means one...

Yet another part cooling fan duct for the Anycubic i3 Mega S (should work fine for the non-S Mega, as I believe they have the same fan and X-carriage cover. I recently upgraded the hotend to an E3Dv6 and due to the geometry when its installed, I...

Yet another part cooling fan duct for the Anycubic i3 Mega S (should work fine for the non-S Mega, as I believe they have the same fan and X-carriage cover. I recently upgraded the hotend to an E3Dv6 and due to the geometry when its installed, I...

A remix of https://www.thingiverse.com/thing:4298177 Lengthened the mounting tabs by 3mm and made the holes into slots so it was more adjustable. Allows to use a E3D V6 or clone hot end without a shim, giving full access to the PTFE pneumatic...

Part cooler for the original fan from Anycubic i3 Mega / S. Supports integrated. ... Only print supports that touch the print bed.

This is remix of llapao's "Anycubic I3 Mega 5015 duct fan cooler ultrabase". I chose the crescent-shaped duct version as it's the most compact design that doesn't obstruct your view & access to the nozzle. So I flattened the crescent duct further...

i accentendly bought M10 bowden screws, so I needed to print extra versions of this part. ...one is with a small diameter for TPU and one for all the rest

Kurzgesagt meine Empfehlung ist die Verwendung von PETG oder ASA Filament. Ich empfehle beide Teile zu drucken allerdings sollten die Lochabstände mit dem Original Gehäuse übereinstimmen. Die Fusion360 datei kann auf anfrage erhalten werden....

Printing should be easy without supports, some bridging is neccessary, but for me this was no problem to print with the stock I3 Mega single parts cooling duct. To mount the duct properly to the part cooling fan, use M2.5 nuts, because we have no...

Yet another take on part cooling fan improvement for the i3 Mega S. This design uses the existing fan and carriage and allows for cooling from both sides. I performed a bit of CFD to help ensure airflow doesn't hit the nozzle, as much as possible. I...

I modified the part cooling model to fit a 40mm fan. It's one piece. ... Keep in mind to print it with support on the heatbed **only**.

Here's remixed duct for Anycubic i3 Mega. Uses standard 5015 blower fan. Clips of duct will be tight, wiggle duct while pushing on bearings. As requested added mirrored version of cooling duct. Added also adapter for 40mm fan, design may not full...

For details, please see the description below:     Summary   Here's remixed duct for Anycubic i3 Mega. Uses standard 5015 blower fan. Clips of duct will be tight, wiggle duct while pushing on bearings.   As requested added mirrored version of...

Original filament sensor upper parts had been deformed. So I made the strong type adding some ribs. ... https://jibundeyarou.com/filauke01/

This is the first and the most important upgrade for your Anycubic i3 Mega S as it dramatically improves cooling and thus PLA print quality. It mounts on the X carriage mounting plate, so no disassembly of X axis is necessary. This is important,...

Hi, I did the E3D upgrade and couldn't be bothered to print the spacer for it so no I needed to draw and print new cover and nozzle for the part cooling fan. ... I'm using the original fan and I've removed the bed level sensor so cannot confirm if...

1mm above the nozzle to avoid collision while parts are warping or curling. It was designed to fit a Sunon 5015 (MF50151VX-A99) blower. 2019-05-06 Added a V2-Version: -Increasing air velocity by reducing number of holes to get a more focused...

... keep warm curtain. ... Prevent to wrap ABS objects if use this item. Corner parts is suit for 6mm dia aluminum tube. The curtain is made of heat insulating mat. Transparent plastic is put on the window. ... https://jibundeyarou.com/i3mega_kakoi/

はるかぜ氏のダイレクトエクストルーダー導入後、ケーブルを本体へ固定する為に制作 https://www.thingiverse.com/thing:3954252 ボルトが純正のままだと長さ不足だったので35ｍｍ/M3鍋ボルトへ交換しています。 もしこのパーツでボルトがネジまで届かない場合はネジ頭を火で軽くあぶって押し込んで 微調整してみてください。（火傷注意！）

Intended to be used with https://www.thingiverse.com/thing:3813245 Or https://www.thingiverse.com/thing:3351666 Takes a 5015 turbo fan like this https://www.aliexpress.com/item/32874940278.html My fan is secured with some duct tape because...

I upgraded my i3 Mega with a direct drive Extruder and a E3D lite v6 Hotend. As this is much shorter than the Hotend that comes with the printer the fan duct would have crashed into the bed. ... So I upgraded the side wall with a better fan position...