arcade spinner 3d models

These are 3D printable parts that can be used to make this really nice arcade spinner using mostly 3D printed parts. I replaced the main 1/4"-20 screw with a 5/16"-18 threaded rod so that I could use leftover Prusa Mendel parts to make the spinner.

I made this spinner control for my MAME arcade cabinet. It functions as a USB mouse and can be assigned as a spinner control in MAME for games such as Tempest or Major Havoc. In addition to the 3D printed part you will you will need: 1. Arduino...

Re-mix of the illuminated spinner. Tweaked the size for the bearing to match that found in Atari trackballs, size of the shaft to fit the smaller bearing, and a replacement encoder (disk versus 'cup' based). ...

For the rest, google "diy arcade spinner" and you will find all kinds of well written pictorial guides on how to build one of a variety of spinner designs that use the guts from an old ball type USB mouse. There are even some that use optical mice as...

This is a DIY illuminated arcade cabinet spinner. Estimated costs are less 10€. BOM: ITR9608 2x (0,40 €) WS2811 5mm 4x (1,00 €) Arduino Pro Micro 1x (3,00 €) Ballbearing 8x22x7 mm 1x (1,00 €) M5x16 screws 6x M5 nuts 6x M3x16 screws 5x flat ribon...

DIY Arcade Spinner that uses an optical mouse. Just stick the optical mouse on the bottom of the base withe some hotglue or double sided tape. ...

This is a shell for a USB arcade spinner built around an stm32f103c8t6 blue pill (or clone), an AS5601 hall-effect magnetic sensor, a skate bearing, and arcade buttons. Build instructions are...

A simple arcade spinner suitable for a 28mm hole I added 2 standard bearings from the old rollerblade, a screw m3 10mm and a fork encoder with relative ring nut like thishttp://ebmstore.it/image/cache/data/SENSORI/Movimento/Min/encoder-b-700x700.jpg...

Picked up a Spintrak arcade spinner for Arkanoid, Warlords, etc but did not want to drop the 70 USD for a stearing wheel accessory. Prints in three pieces and uses nine 4-40 X 1/2 sheet metal screws and nuts to hold it all together. The three...

Picked up a Spintrak arcade spinner for Arkanoid, Warlords, etc but did not want to drop the 70 USD for a stearing wheel accessory. Prints in three pieces and uses nine 4-40 X 1/2 sheet metal screws and nuts to hold it all together. The three screws...

This is a complete spinner to use with an arcade cabinet. I use this with Mame. Even if there are other design. I had to develop it by zero. What you need. N°1 Leonardo Micro ATmega32U4 16MHz 5V Replace ATmega328 Arduino Mini Stock...

This is a spinner knob designed to be attached to a Happ controls arcade spinner. ... Use a M3 socket-head cap screw to attach.

This is a spinner knob designed to be attached to a Happ controls arcade spinner. ... Use a M3 socket-head cap screw to attach.

This is a steering wheel that can fit over a Glen's Retro Show Arcade Spinner (GRS). You will need supports, I used tree-like supports from my splicer, FlashPrint. Once printed, remove the support material and slide over the GRS Spinner. This can...

This is a knob for a rotary encoder - I'm going to use it as an Arcade spinner for Arkanoid (and Tempest!). I added some weight by a few M5 nuts (and M3 screws) to improve spinning. The holes in the top part need to be tapped so you can...

Here is an inexpensive, High quality arcade spinner. The printed parts include a mounting plate and an Arduino Pro Micro housing. Used to mount a 600p/r Incremental Rotary Encoder to your arcade control panel. The center of the plate can be popped...

I've modified the sketch, removing the joystick interface, since the buttons are handled by my X-Arcade controller. Youtube video showing my setup is here https://youtu.be/AqYDVgHWPoc. ... Youtube video going over wiring and programming...

Here is a push-pull spinner that I designed for my full-sized MAME arcade machine. See it in action here https://youtu.be/APumu_h8S0E. The spinner and micro-controller setup are based on a build I found on YouTube by Joe W. This works great for a...

To position the bottom part of the spinner, I glued a tiny washer onto the mouse and only slightly positioned the bottom spinner piece into the shaft of the top spinner piece and let it slide into the correct depth as I positioned the lid on the...

Please consider supporting me on Patreon to unlock my more advanced 3-piece steering wheel designs (update 2 brings more sizes to the collection) : https://www.patreon.com/3DFreeman If you would like to buy the GRS USB Button Hole Spinner, here is...

... left 1-2mm from the transparent piece. This disc emulates the surface where the mouse moves... it's easy to understand how it works. Put on spinner (threaded) and case (you can use bolts or glue). Look for the cable hole on the case. ...That's it.

Please consider supporting me on Patreon to unlock my more advanced 3-piece steering wheel designs (update 2 brings more sizes to the collection): https://www.patreon.com/3DFreeman I also have a Thingiverse page...

Please consider supporting me on Patreon to unlock my other arcade parts and steering wheel designs: https://www.patreon.com/3DFreeman If you would like to buy the GRS USB Button Hole Spinner, here is an Amazon affiliate link:...

Please consider supporting me on Patreon to unlock my other arcade parts and steering wheel designs: https://www.patreon.com/3DFreeman If you would like to buy the GRS USB Button Hole Spinner, here is an Amazon affiliate link:...

Please consider supporting me on Patreon to unlock my other arcade parts and steering wheel designs: https://www.patreon.com/3DFreeman I also have a Thingiverse page: thingiverse.com/3dfreeman/designs If you would like to buy the GRS USB Button Hole...

I made this Arduino Pro Micro housing for my arcade spinner build. Very little interior room, but I don't need much for this project. I use a few drops of superglue to keep it closed. The Arduino sketch is included in the files. Youtube video...

Please consider supporting me on Patreon to unlock my other arcade parts and steering wheel designs: https://www.patreon.com/3DFreeman I also have a Thingiverse page: thingiverse.com/3dfreeman/designs If you would like to buy the GRS USB Button Hole...

So the only other way would be just to have a spring cable out of the back, but you still would have to be careful not to rotate it too much as the cable would wrap around.If anybody is interested in me creating a fully functional version than please...

This is a multifunction, 2 player capable, USB spinner controller with a single arcade button. It's extremely cheap, and easy to build, print, and assemble. It uses a rotary encoder, which means that there is no left or right limit, it can be spun...

The large version is about 224mm in diameter, the small version is about 112mm in diameter. If you scale in slicer the shaft hole will also scale so may not fit if scaled. ...I used .2 layer height for the small and .28 for the large so it printed...