ath m40x repair 3d models
16555 3d models found related to ath m40x repair.thingiverse
Replacement hinge for ATH-M40X. This is the left hinge. I could not find other hinges that were satisfactory for my needs. This is designed to be printed in resin. ...The wire that passes through the hinge needs to be de-soldered from the jack, pulled...
thingiverse
This is a replacement part for Audio Technica ATH-M40x headphones. I believe from around 2016, yours may differ. Mine already has a longer metal band in the hinge like here: https://imgur.com/a/BT9mG . If you like it, consider a small donation...
myminifactory
Phone stand that slides onto the headphone jack for the ATH-M40x, good for movie watching. ...I don't have calipers yet so the measurements were estimated, and I spent 30 minutes filing down the hole from the original design, the uploaded stl has a...
prusaprinters
Hinge for the Audio-Technica ATH-M40x. I tried out the version from thingiverse (<a href="https://www.thingiverse.com/thing:2823187">https://www.thingiverse.com/thing:2823187</a> ), but I thought it didn't fit well so I recreated one myself.</p><p>I...
thingiverse
Left hinge part for Audio Technica ATH-M40X headphones. Modeled with Tinkercad, this is the second iteration of the part with better fit and addition of stoppers to keep the earcup from turning over. The wedge part is a bit too tall and doesn't...
grabcad
A desk mount for my Audio Technica ATH-M40x headphones. ...The mount is designed to easily slide onto the corner of the shelf on my desk, and provide a simple, unique, and out-of-the-way storage space for the large headphones.
thingiverse
Phone stand that slides onto the headphone jack for the ATH-M40x, good for movie watching. ...I don't have calipers yet so the measurements were estimated, and I spent 30 minutes filing down the hole from the original design, the uploaded stl has a...
thingiverse
The screw socket for the connector on the Audio Technica ATH-M40X breaks easily with normal use. This makes the cans (the speaker section) likely to fall off of the metal mount and cause further damage. After both broke on my headphones, I designed...
thingiverse
This is a replacement hinge for the Audio-Technica ATH-M40x headphones. This is the most complex thing I've made in AutoCAD so far and there have been quite some prototypes before I got to this version. **Note** This replacement is compatible...
thingiverse
I like and used the fix design in https://www.thingiverse.com/thing:3219753 for repairing my headphones, but found that the thicker portion of the pivot shove could have gone up further to avoid more slop and wiggling This bushing slides down to...
thingiverse
Replacement part designed for Audio Technica ATH-M40X headphones but might work on other similar headphones like M50s (I haven't tested this). If you ask me I would be willing to make a few small changes to the design if its simply widening a hole or...
thingiverse
I often use my ATH M40x headphones without the Modmic attached, so have a quick clip system instead of using the default clips is much handier. They're roughly designed after the default modmic clips, but moreso iterated for a tight, no-slip clip on...
pinshape
What: Hinge repair bracket for AudioTechnica ATH-M50x Why: The one obvious mechanical design flaw on these otherwise incredible headphones is the design for the plastic tab that prevents the ear cups from rotating past the point of sitting over your...
thingiverse
3D printed end stop for the Audio Technica ATH m50X. Its similar to the ones being printed on ebay except with one uses two M3 screws to camp to the headphones. ...They work great and saved my headphones.
thingiverse
A modified version of the root, more friendly for extrusion printers, and for 5mm cable ties. ... for best results, print on the side.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=45424 Instructions Using the following options: tagH = 20 length = 100 width = 50 textT = 5 Font = write/orbitron.dxf build_plate_manual_y = 100 build_plate_manual_x = 100 edge = 5 tagThickness...
myminifactory
This is a couple of repair parts for the Audio Technica ATH-910 PRO headset. The files include the main earcup holder and the tiny clasp used in the back to hold it onto the main pin. ...These pieces will work on either side.
thingiverse
This is a couple of repair parts for the Audio Technica ATH-910 PRO headset. The files include the main earcup holder and the tiny clasp used in the back to hold it onto the main pin. These pieces will work on either side. I recommend a decently...
thingiverse
Made printable version of the parts for a common issue on the Audio Technica M40X headset. ... You want to also print flipped x or y versions of the cup fork, and the rotator mount for symmetry.
thingiverse
Customized version of https://www.thingiverse.com/thing:3395463 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3395463