ide adapter 3d models
120780 3d models found related to ide adapter.thingiverse
I made a spacer for a SATA to IDE adapter to be used in the original xbox. ...This is ongoing project so there may be changes.
thingiverse
simple protector plate for a Sata-IDE adapter to protect against short circuit on the harddrive it self. I printed this in ABS to be sure it will last because of potential heat. ...
thingiverse
This device allows you to mount the cheap and common sd to ide adapter pcb to the built in hdd slot on a beige MAC G3.
thingiverse
3.5" bay for the compact flash to IDE adapters. This one should work splendidly for Amiga 1200 Towers or Amiga 4000. Instructions Made in SketchUp - skp-file included. ... Fasten the adapter to the...
thingiverse
This is a CF card to IDE port adapter bracket which can be used i.e. ...in the Amiga 600/1200 and protects the Amiga motherboard.
thingiverse
A simple thing to tidy and help secure the CF IDE adapter under the TF328 (if that's where you want to place it). Prints in about 6-12 mins depending on your printer and settings. 0.2mm layer height works well with 100 percent infill. ...
prusaprinters
A simple thing to tidy and help secure the CF IDE adapter under the TF328 (if that's where you want to place it). Prints in about 6-12 mins depending on your printer and settings. ...0.2mm layer height works well with 100 percent infill.</p> <h3>Print...
thingiverse
I designed this for the Syba CF->IDE adapter, which I've used many times, and have had good luck with. With a few minor modifications, it could probably work with other adapters (and other completely different applications) as well. The mount has...
thingiverse
(so here we are) Adapter Used for this design: (Available on Amazon - See Pic) Manufacturer: Mustpoint Desc: SD SDHC MMC to 3.5" 40Pin Male IDE Adapter Card Big PCB SD-3.5 IDE PC Board Labeled: SD35VC0 Dimensions: 80.2mm * 70.2mm Design can easily...
thingiverse
... batch to another, so the clearance on this model is a little larger to accommodate. I use mine as friction fit. Fits 57.5mm*41.5mm mSATA to 44-pin IDE adapters. ...8.4mm total adapter height, to account for variations between people's 3d printers.
thingiverse
This is a remix to shorten up the mount a bit, and raise the cf card up off the floor on some standoffs. ...This also as a an overhang to keep the molex to berg cabling in check.
thingiverse
... to solder it in place of the original SMD LED which you will want to remove (as it will shine through the plastic). https://www.hexin-technology.com/HXSP-2118P_CF_to_IDE_Adapter-Product-400.html http://www.soarland.com/CF_CFast-catalog-41.html
cults3d
This is 3.5" bay enclosure for HX-2118P (also known as SLCI4001, HX-118, HXSP-2118P or HXSP-2108P) Compact Flash to IDE adapter. 4 variants available (wider and flush front as well as shorter and longer variant. Should fit most AT and ATX cases...
thingiverse
ORIGINAL SUMMARY [I didn't designed this Thing, I ONLY corrected the error from the STL file] ORIGINAL CREATOR: https://www.thingiverse.com/dogp/designs This is a bracket to install a CF->IDE adapter in an internal 3.5" hard drive bay. I collect...
thingiverse
This works great if you're using SATA drives in a SATA system, but it can be problematic if you're trying to adapt a SATA drive for use in an old PATA/IDE system. This adapter sets the 2.5" drive back far enough that you can fit a SATA-PATA adapter...
thingiverse
This is a bracket for the IDE to SD card from https://www.amazon.com/gp/product/B07YFPX7JB There is a "long" and a normal version of the bracket; if using the normal version please verify the dimensions are correct as the "long" version has the...
prusaprinters
After printing I filed down the light pipes to a snug fit in the housing, then after mounting the adapter pressed the light pipes into the LED holes, seated them over the SMD LEDs, and hot glued it in place. The housing should be seated...
thingiverse
Its purpose is to keep the adapter in place during shipping, and to act as a protective barrier against accidental shorting of the MOLEX input solder points on the back of the board. Designed to fit the cheap (less than $4) Chinese adapters you can...
thingiverse
I just did a quick tinkercad bad remix on the original to get it to fit correctly on my setup. ...I figured I may not be alone here so uploading for others
thingiverse
So I decided to take on the challenge my self of making a 3-1/2" drive bay enclosure for my SD to IDE adapter. This project will require some basic soldering skills as you have to de-solder the Molex power connector and solder wires directly to...
thingiverse
... bracket. This slot adapter is modeled after a 3.5" floppy drive's dimensions to neatly fit in those slots. ... There are a few different versions of the SD boards out there; I'm not entirely sure which one he's got, so compare with the pictures.
cults3d
This is a drive bay cover for a HXSP-2108P IDE to CF adapter. It allows insertion and removal of the CF Card from the front of the machine. I have provided both the STLs and the Source files which were created in 123D. The board I used in the...
thingiverse
This is a drive bay cover for a HXSP-2108P IDE to CF adapter. It allows insertion and removal of the CF Card from the front of the machine. I have provided both the STLs and the Source files which were created in 123D. The board I used in the...
thingiverse
Adapter sled for IDE to SD card adapter for a Macintosh Performa models using the Performa/Quadra 630 case.
thingiverse
Internal mount for IDE To SD adapter with front cover. This version is for a 3.5" drive bay. ... Required: (x8) M3x5 mm screws ----- The 5.25" drive bay version is available at: https://www.thingiverse.com/thing:5642192 -----
thingiverse
This is a small mounting bracket for [this IDE to SD card adapter](https://www.amazon.com/gp/product/B00DGNYXQ0/), to allow it to be mounted in place of a 2.5" drive (10mm high). Photos show it installed in a PowerBook G3. The bracket includes two...
thingiverse
... Any M3 screws will tap themselves in the holes. Search "IDE SD" on amazon and you should find a comparable adapter to original product photo above. I did not print the "inverted" version, so let me know if my measurements work or not. ...
prusaprinters
The power wires still exit on the front. Any M3 screws will tap themselves in the holes. Search "IDE SD" on amazon and you should find a comparable adapter to original product photo above. I did not print the "inverted" version, so let me know if my...