shift knob for logitech g29 3d models

Use an M4x40 bolt to secure it in place.

Measured to exactly fit my hand! It has a cavity inside so you can add weights to your liking, you can use fishing sinkers to do that, they work as charm. Once you are finished, just put gently the bottom, it will fit. I've used PLA850 -...

Printed the skull with 20% infill and the rest with 50% infill. Make sure you dont overtighten the screw or it could brake. ... I used a glue to stick the skull onto the rest an it`s still holding together.

lots of overhang under the cap part might need to sand or peel plastic for good fit cap does not spin easily and fits snug but can still be removed for screw access Shifter that it's designed for: https://www.thingiverse.com/thing:4744688 might work...

simple shift knob for logitech G29 sim wheel

This is a shift knob for a Logitech G29 shifter. ...No extra hardware is needed, this uses the original screw.

Use original screw to secure on shifter. ...Original gear knob cap, from the driving force shifter, fits to cover hole.

This is a shift knob i made myself. It will fit on a Logitech g27 and on a G29. I made this in Tinkercad and printed it afterwards in silk gold PLA and as you can see it looks really good. To screw the knob on your shifter i fitted a turning knob on...

This is a shifter knob for the shifter that comes with the g27/g29 wheels from Logitech. It is a pressure fit so you don’t have to screw it in place like the original knob. I recommend printing it with a fairly dense infill ~60%, not because it is...

shift knob for logitech g25 and g27 possibly also g29 but i am not sure this uses the original hardware you just take the old one of and slide the new one in and put in the screw and just put tha cap in the hole if it's tight enough

Greddy inspired shift knob for a G29 Shifter. There are two parts to it so the original screw can be used. One part is the shift knob and the other to close the top off. I tried to get a Greddy logo to work at the top but the logo is really slim and...

It's an adapter to mount any shifter knob with a m18x1.5 thread to Logitech g920 / g29 shifter.

It's an adapter to mount any shifter knob with a m18x1.5 thread to Logitech g920 / g29 shifter.

Wanted a different shift knob for my Logitech G25 and made one! The hole in the middle is a little bit smaller than 10mm so you need to drill it up to 10mm. Made this for better fitment... ... Hope you like it :)

This adds a vibrator motor to the shift knob of the Logitech G920 (and I assume G29). Use this with SimHub to get feedback when shifting gears. Gear grinding doesn't seem to be supported any more but it's still very useful with the gear shift...

Original is noted for the G29, mine is a G27 and I am fairly sure no changes have been made for the shifters on the G920 and G923 so it should work, but untested. Update 1 (7/7/23) - I just added a -25mm version, this is about the min height you...

Replacement cap for Logitech G27 / G29 / G920 gear knob / H-shift By request a version with no detail on top face.

Replacement cap for Logitech G27 / G29 / G920 gear knob / H-shift There are 2 versions one with a slightly bigger peg as this is designed for an interference fit and printers can vary with accuracy. ...

This simple part allows you to use any m12x1.25 shift knob easily with the logitech g29/g920 shifters.(may work with others but not sure)

This is a custom paddle shift for g29 wheel. It is designed looking for more ergnomics when you use this custom wheel for g29 https://www.thingiverse.com/thing:4250782 To make sure it will works fine when you install it you have to tigthen the...

This is a custom paddle shift for g29 wheel. It is designed looking for more ergnomics when you use this custom wheel for g29 https://www.thingiverse.com/thing:4250782 To make sure it will works fine when you install it you have to tigthen the...

This is a shift knob adapter designed for shift knobs that come with inserts. I used this one:...

... you get switches that stay in position and don't return to center. ...I made the mistake of buying some that would return to center so pay close attention. It's a tight fit for the switches so no glue is necessary. ...Light sanding might be required.

Logitech G29 Paddle Shift Extension for converted Steering Wheel

# This is a shifter knob for Logitech g29 shifter Inspired by MOMO shifter knob. This is a smaller version than the original knob. Original: 130 mm, mine: 94,5 mm. ...The stock shifter knob is small for me and I've designed this one.

Logitech G29/G920 Knob

This is a racing gear knob for Logitech G series. ...Have fun using it!

Magnetic mod for Logitech G29 steering wheel paddle shift. Use 4x 6x3mm magnet (6mm diemeter, 3mm thickness). ... According to the version you downloaded, you need: - 2x M4x20 TCE screw - 2x M4 nuts OR - 2x M3x20 TCE screw - 2x M3 nuts

these are Extentions for the G29 if you build an real Steering Wheel on it.

This 3D model is for the logitech G29 shifter. I made this shifter knob because i was bored about the traditional shifter ball and I wanted to make the gear lever more ergonomic. This shifter knob need a screw adapter to be mounted on the gearbox.