spool of film 3d models

Installation: To install a spool of film, I slid the non-pin keyed adapter (referred to as 'cross') onto the top film advance pin. Then I inserted the '+' on the other end into the film spool, inserted the other adapter/spacer into the other end of...

Film spool of my agat 18k is broken so i made this. ...It may work on another type of cameras that use film spool but i didn't tried it.

It is possible to cut down 120 film to 127 size or to buy a bulk roll of 46 mm film and backing paper. Still, you need a spool to wind the film on. If you don't have old spools (or the slightly-too-wide plastic spools made by Efke jam in your baby...

620 film spool Instructions Spool for use in respooling 120 film for 620 cameras. Suitable for SLS printing. See the two-piece spool by ComradeQuiche for a MakerBot-compatible version. The photo shows a standard 120 roll, a 120 roll re-spooled on a...

Print the two parts and snap them aligning the three cylinders located near the center of the spool. Use glue to make sure it doesn't separate when turning. ... Print Settings Printer Brand: RepRap ...

A 35mm film spool used in a Taxona camera. ...Might fit some other 35mm cameras, but I have not tried.

Instructions 10 Print 20 Clean out support in drive opening at ends 30 Glue with super glue 40 Shoot some awesome photos 50 Get a new spool from the roll of film you shot 60 Goto 40 I've gone as far as printing this and gluing it together, but I...

... two halves together, use a few drops of glue to secure them if you like. The ends of the spool are quite thin, so depending on your print material, it might be recommendable to use black spray paint on the finished spool to make it more light proof.

Instructions This is a basic spool for 120 film. This should be fully usable, and you should be able to use it to wind film onto. Measurements were taken from an existing 120 film roller, so I believe everything should be within specification. The...

## Spool for 120 film type **No support required** **No glue required** All the spools I found were either unprintable or unusable so I decided to design my own I made an interlocking cube 0.2mm smaller than the corresponding hole, so that the two...

... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=45101 Instructions Using the following options: spool_walls_diameter = 180 filament_diameter = 3.3 unit = 1 spool_hole_diameter = 70 spool_width = 9 spool_walls_width = 3

... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=45101 Instructions Using the following options: spool_width = 20 unit = 1 spool_walls_width = 3 filament_diameter = 3.3 spool_walls_diameter = 180 spool_hole_diameter = 70

spool for photo camera film

... 8 sprockets but using the scad module spool() with a parameter will generate a spool of a different number of sprockets. Because of the spacing of the film holes changing the number of sprockets changes the circumference (and radius) of the spool.

the one film for animated

Film of the pandaCategories for "monster", with large ogre as the theme, in the creation of 08-15 years by uploading material game of my dreams. ...Artstation design network to continuously updated and related quality Artstation you download material...

Film 3 magnets that are used in factories Cement Factory

UPDATES 10/23/14 - Added matching takeup spool http://www.youmagine.com/designs/120-takeup-spool-for-35mm-film 10/7/14 - Added a combined STL 7/6/14 - I've added a PDF Read Me guide to using the adapter 6/16/14 - updated files to improve fit and...

 While this is designed to be a perfect copy of a 620 spool when the top and bottom parts are inserted onto a 35mm film canister, the spool and 35mm canister are physically larger than a 620 spool.  YOU MUST FIRST CHECK AND SEE IF A 35MM FILM...

... ...Can also be used to transfer film from one spool to another faster than my Eumig 502. ...But be careful not to tear the film! Connect the tool in you reel, get your electric screwdriver or other fitting tool, and connect it like in my pictures.

The hole for viewing the film number (usually a red window) on the camera must be taped over with black gaffer's tape or some suitable opaque tape to avoid back side exposure of the film. You will need to wind blindly about 1-1/2 turns at the...

The hole for viewing the film number (usually a red window) on the camera must be taped over with black gaffer's tape or some suitable opaque tape to avoid back side exposure of the film. You will need to wind blindly about 1-1/2 turns at the...

Here is a remix of coconnor55 spool adapter. ...Now you can fit 35mm on your 620 kodak camera

Customized version of https://www.thingiverse.com/thing:735213 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=735213

This is a remix of a part from a Thingiverse model (https://www.thingiverse.com/thing:4711177  by blaskkaffe ) , that I customized to better fit my camera (Kodak No3 folding camera). Slightly increased widths on the slots,  improved...

A 620 film spool for medium format cameras. 120 film spools are easy to come by, and can be bought new at camera stores, and online, but 620 spools are harder to find and can cost way to much for what they are.Though 120 and 620 spools are very very...

Luckily, you can load a 620 spool into the back of the camera, and use a standard 120 film spool for take up. I made this model because although you can find 620 spools, they are a pain to find and people want way to much for them! ...

Adaptor to place a 120 film spool into a 116 film camera

This is an film spool adapter to use 120 film in cameras that originally took 116 or 616 type film. Note: this does not mean that the "red window" numbers will line up, just that you will be able to load 120 sized spools into the camera. There are a...

... would fit the original film. The original film was apparently ten frames of 14x14 mm pictures - with these spools I only get about 8 frames on them (that is, roughly 15 cm or so of film, with 22 cm or so of backing paper). ...Your mileage my vary.