1 10 scale 3d printed engine

I guess you can say a TEST, Clear off your desks and print one (OK maybe two), paint it and then post it as a make to let me know what you think, maybe just maybe, if its worthy, I will make a complete set of the better variations that get discussed...

Part List: PlungerTubeButt-m: This is a printed version of the shortened Plunger Tube End if you prefer not to cut any polycarb or acrylic tube. SearSpacer6p60x9: This spacer secures both ends of the Sear part with screws. I couldn't find an...

It's pretty to look at, and educational! Assembly:      Things you'll need:Super Glue/Plastic glueSkateboard bearingsRubber bandsYou'll need to print everything once, except the pulleyLarge, you'll need three of them.Assembly can be a little bit...

But as usual, enjoy :)Make sure to use a strong filament to print the parts.  PETg, ABS, Etc.I went ahead a published this, but A LOT more info needs added.  I will add the rest later, I wasn't very prepared to add this to Printables, ( It was meant...

Follow the instructions at https://www.thingiverse.com/thing:5066794Attach display units to the base, using 2mm tapping screwsFix the top of the neighboring display units using retainer.stl and screwsAttach Ks0360 board to the bottom of the...

Although the filter mount does not have threads, it does have print layer ridges that make snapping a threaded filter into it very easy. I found 0.150mm layer height gives the best results for fit and retention.The belt clip module features easy...

This new Case is only good for the 2730 Monitors.\r\n\r\n10-13-2019: I've updated the Lower Case with a higher Monitor Mount Block to mount the Laptop, I've also notched out the edges so the lip of the Mount can sit flat.\r\nI've also made the Mid...

This model can be printed as an educational tool to teach students about the connections between the different parts of the ventricular system. It has been made possible by using medical data sets available online and post-processing them with mesh...

Print Settings Printer Brand: RepRap Printer: Folgertech Prusa i3 Rafts: No Supports: No Resolution: .2 mm layers Infill: 20% Notes: I used PLA, but other materials would work fine. ...My printer has a 200x200mm platform and the fuse is exactly 200mm...

... hotend versions available, one with BLTouch and one without. If you are using a BLTouch, you also have to print the "BLTouch_mount". The probe offset is: X=+30; Y-17. If you encounter any issues, or have improvements, let me know! ... Cheers.

To print the nose, I recommend using supports everywhere and 20% support density, along with 20% support density on the LID. For the lid itself, use 40% infill and make sure to enable the brim. Don't worry if the supports fail on the lid - it seems...

This is the second day of my President's day freedom print week, I will post a new piece of art every day that advocates for People's rights and freedoms across the Globe. I will be posting a lot about the events that have unfolded in Hong Kong and...

My take on articulated silhouette models of animals. I've seen some similar models with wide open hinges but thought I'd try using a masked type hinge so you can't see through the hinge lines Others in the series:...

... I've included five variants of this code, each creating different types of enclosures. The first one is purely a demonstration and hasn't been printed yet, while the others have all been used to create devices (and thus come with pictures, etc.).

(this is not the final version, some of the designs may change, if you incounter a problem with the design, please let me know)Everything is ment to be put together with only M3 screws, nuts and washers, but i havent measured everything up yet, so...

... I added two options A. Full figure, just one print, one color (ONE PIECE.STL)(USE SUPPORTS) B. ...Color assembly with 6 pieces  Base Base Ring Body Comb Wattles Eyes -------------------------------------------------------    

I designed one; you can find it here: https://www.thingiverse.com/thing:3552100 Please take a look at the videos in the "Post-Printing" section to see it in action: https://youtu.be/5obEBf6tcjY! **EDIT:** I designed, upon suggestion by some of the...

The pictures show the white prototype since I did not print the final thing in black (or transparent maybe) yet. The new pictures with the black buckle show the final version with an individual text / number and some comparison between ootes'...

(No need for 100% infill, as these are meant to be hollow to accommodate the emitter.) Printing may require supports. I have assembled a complete hilt using all the files and taken photos. The top and bottom buttons fit tightly but work well. Make...

The cover uses one original screw - and you have to put a countersink screw on the other side if you want to use the height adjustment key through the router base (manufacturer's design flaw). The cover might also need a bit of filing on the...

Print these parts with ABS @ 0.33mm Layer Height, 95% Infill, Octet Fill Pattern (Tetrahedral), in a sealed enclosure for proper inter-layer adhesion. To use the Hang Adapter with integrated Wire Concealer, you'll need: * The Mosaic Palette 2 Pro...

Still working on printing the final versions and testing them, so things could still change, but i feel like they are at a good enough state that there shouldn't be any major changes. Depending on how well the mount is able to hold up the light on...

Note that there are revisions of the model which also allow for rubber feet to be printed with it. You can replace these rubber feet with cut down SKUF rubber feet if you have them, or if you can manufacture the feet yourself that is best. I...

...The right case lid has a gap in the back for an RPi camera cable, which I actually printed the wrong version of, so I don't know how well it lines up or fits. I'm still waiting on my components to arrive and will add some action shots when they do.

For more information on the Breadboard Kit and the other modules required to complete it, please check out the link below: https://www.thingiverse.com/thing:3416074 I'd like to extend my gratitude to Mathgirl for sharing her amazing print-in-place...

I got the idea from https://www.printables.com/it/model/30811-mmu-slot-buffer made by Martin_J., from which you can download the original files I only modified the lower part, the dividers, made some closed slots and two holders. Remix Components:2 x...

It's TPU-based, meaning, it won't be strong if you print in PLA. Trust me. Tried that just to see, and decided TPU is the right material. The only thing about this design that I'm not totally happy with is easy access to the VTX band/channel buttons...

There's also a larger tray for cool gantry blocks that you've probably printed by now, as well as space for feeler gauges. You can even put nozzles and clips in the little tray - both of the tray areas are very tapered so you can slide the small...

This is a customized carriage for the Wanhao i3, designed and printed over an extended period of time to achieve maximum lightness and minimal weight. The primary reason behind designing this carriage lies in its ability to weigh significantly less...

... used Meanwell power source and relay module on my photos from montage. The holder for Mosfet, Power source and Relay is not part of this design. All parts were printed from PLA (PETG would be also fine), 0,2mm layer, no support, 25% infill. ...