1 10 scale engine 3d models

These can be used to control the elbow joint with more precision) - Standard Servos x2 (Only one servo is necessary for the joint but I designed the arm to hold two just in case one wasn't enough to lift the arm and for lifting heavy loads) - Micro...

Required parts: 20 mm Piezo disc Precision Piezo PCB v2.75 (can use other but won't fit this PCB mount) 4 Springs like these or similar 4 M4 lock nuts 4 M4x12 bolts (or longer) Installation (X-carriage): Remove the upper bearing block of your...

 Reasons for choosing this enclosure are.1. Better environment sealing, to reduce fumes from escaping into the environment and provide an warmer environment to reduce print warpingprint.  This enclosure has only one opening at the door and it is...

Cursed Immortality Season 2 - (1/4) The Ironbound - Curse of Iron  Description Feris was a student of the Arcane in his mortal life, and a brilliant one. He was chosen as an Honor student during his early years in the Ministry of Arcane Arts, solely...

Roll-in or hammer head.1x5x2[mm] Magnets for Back Housing and Mount6xFoam Tape to protect the ribbon cable-________________________________________________________________________________________________________________Slicing InstructionsMaterial:...

Really, the better deal seems to be the SGEN_L v2 right now, since it is roughly equivalent to the SKR 1.4 Turbo with just a couple minor feature differences. For extra safety, I trimmed the pins that might potentially touch the head of a screw...

Bi-Directional, Rotating Digital ControllerHere we have a 3D-Printed Bi-Direction/1-Axis Disc Controller I made for my Arcade Prototype Controller. I've only used it for Stage/Unit select in games so far, but it also could be used in 2D platformers...

I have started with the Official Metric Remix, which is mostly adjusted for M4 screws and 12 mm rods, and adjusted as needed.PrintingEverything printed with variable layer height, 0.2 mm base profile, 3 perimeters, minimum 1.2 mm bottom and top...

I had to extend a 1 metre cable to do this and provide a separate power feed to a spare 5v pin on my BTT E3 Mini board.I have also remixed a fixed variant of my Slim Display Housing to sit inboard of the Ender 5 Frame here:...

It should rotate 1/4 turn from the locking pins being fully extended to being all the way retractedGENTLY screw in the 2 M3x6mm screws to retain the feeder assembly in the hopper base. If the feeder doesn't rotate anymore, back out the screws...

With the Bowden I had it set for 1.0v but with the direct drive, I dropped it down to 0.5v and it works great. I originally had it set for 0.8 but the pancake motor ran way too hot and the print quality suffered greatly. Once I dropped it down to...

Cut the remaining “hairs” to a length of 8mm with a pair of scissors.Looking at the remaining piece, still in the same orientation, cut a part out of the bottom of the piece under row 4+5 (row 1 is left), like in the pictures. Now the “new” brush...

This will make the PINDA led (visible from the top of it) work.Insert the small (1.5mm) allen key that came with your Prusa into the small hole you'll find in the side of the MSU Selector. This will push up the steel ball inside of it, simulating the...

However, the connection can be undone again with force.&nbsp;Sometimes you only have one controller, so you have to share it. With the quick release, you can remove the controller completely or with the slide with one screw.</p><h4>As individual as...

They've been tested over several hundred miles of riding, in the deserts of Utah and Arizona, Kingdom Trails in Vermont, and various Cat 1 and endurance MTB races in the northeast. My initial prototypes were printed in PLA, and I had issues with them...

Basically you can just take a small length of 1.75mm filament, place a small amount of narrow heat shrink over it, and hit it with your heat gun until they bond. Then, cut the filament and stick the cut end into your astronaut. Then, shove the...

You don't actually need to print it, you just need a small piece of filament.The version without the seal works just fine but you may need to pay a little more attention wen agitating the tank.MATERIALS3D printed componentsa small piece of 1.75mm...

CAD Cart 1 is the ultimate one-stop-shop for CAD, render, video, 360 view, catalogue, and model view services for diamond jewellery designs. We specialize in providing precision-created CAD files for a wide range of stunning diamond jewelry pieces,...

Cad cart 1 is the ultimate destination for comprehensive CAD, rendering, video, 360-view, catalogue, and model view services tailored to diamond jewellery design requirements.\n\nWe provide an extensive range of high-quality CAD files that cater to...

Cad Cart 1 is the one-stop solution for cad, render, video, 360 view, catalogue and model view for diamond jewelry designs. We are providing CAD files of various types of rings. These include: Engagement Rings - The classic choice for couples. Ear...

Both the front and back should be done with at least two layers of outer shell; I tried using 1 layer, but rigidity simply wasn't good enough and lightproofing would have been more difficult. The screw that fits the tripod socket of the ELPH 115 IS...

Have fun and spend time with your family assembling this beautiful christmas ball.Dimensions: 70x70x73 mm&nbsp;Instructions&nbsp;Assembly is pretty straight forward and repetitive, not hard.You will need:20 x Face11 x Connector1 x Connector with...

Cad Cart 1 is the ultimate solution for cad, render, video, 360 view, catalogue and model view of diamond jewellery designs. We provide accurate cad files for a wide range of exquisite diamond jewelry pieces. Our expertise in providing cad files...

Most likely you will need at least one additional fileset, the additional universal parts. Here is a complete linked list of the (currently) available additions:File sets to add special features (printer-independent):Additional universal parts -...

Mark the whole rectangle “for construction.”Bottom Triangles:Add a construction line 1 cm off the bottom of the constraint boxFrom point A, using the line tool, draw a line segment to point B. From there, using an automatic perpendicular relation...

To make the cover for the gun start by cutting out a 1.5” slot down the length of the tube. This wil need to be opened up in some spots to clear the mounts on the aluminum tube but this will need to be done slowly as you want the pvc tube to...

This is a servo hinge setup for use with MIPRESIDENT's Iron Man Mark III helmet (http://www.thingiverse.com/thing:260152). You can see my final build here: http://www.thingiverse.com/make:286759 And a video of it in use here:...

Update 08.01.2022: Added some examples for test patterns included in this model.Update 12.01.2022: Updated presliced gcode to make sure heatbed is turned on.Update 18.01.2022: Uploaded additional stl with text on test patterns describing its...

Instructions are as follows: 1. Print all the parts. Remove gantry frame from the printer. This video from Anycubic explains how, https://youtu.be/NRpfHr2njXs and screw the original metal frame mounts all the up and off the threaded rods. Loosen...

Das Locht dient nur dazu das ein &nbsp;Sechskantschlüssel durch paßt um die Linsenkopfschraube anzuziehen.Die 535mm und 396mm Profile werden Stirnseitig mit einem M8 Gweinde versehen und im Voron Style verschraubt.&nbsp;&nbsp;Print SettingsPrinter...