120mm psu fan 3d models
118156 3d models found related to 120mm psu fan.thingiverse
120mm fan adapter for Prusa Mk3. Hooks are separate from the main part and are somewhat adjustable. ... Not sure if all PSUs are the same but the hooks are separate so shouldn't be to hard to modify.
myminifactory
120mm fan adapter for Prusa Mk3. Hooks are separate from the main part and are somewhat adjustable. ... Not sure if all PSUs are the same but the hooks are separate so shouldn't be to hard to modify.
thingiverse
So I tried a different route, the cover kind of snaps in place, you may need to 'persuade' the PSU box a little though. If the 4 inside clip things are in the way you should be able to snap/cut them off without much issue. Photos are terrible but...
thingiverse
I needed a 120mm fan upgrade for my Maker Select v2, as the stock 40mm fan makes a terrible grinding noise every time I turn the printer on. However, none of the options, by Kozar, worked for me. This is because I am mounting my control box under the...
thingiverse
I wanted a way to be able to control my LED strips around my Di3, so I remixed this shroud to include a relay from Amazon (http://a.co/iozbBre) built into the side, with a hole in the top for the relay wires. These wires go up to my RaspberryPi that...
thingiverse
This is a horizontally flipped version of https://www.thingiverse.com/thing:2468756 so that the position of the plug and cord would be reversed. ... I needed this because my control box is mounted on the other side of my lack table.
thingiverse
You can replace cover of your psu, to be able to install 120mm fan and power connector
cults3d
Adapter allowing to install a 120mm fan instead of the 60mm one on the original power supply of an Ender 3.
thingiverse
Adapter allowing to install a 120mm fan instead of the 60mm one on the original power supply of an Ender 3.
thingiverse
This allows cooling of 2 Power Supply with a single low noise 120 mm fan Video here: https://www.youtube.com/watch?v=4rCoPybnSHI
thingiverse
This is a light weight Psu cover for a 120mm fan setup as the original fan is crazy loud at times. I printed this in Carbon Fibre Pla and its going great the 120mm fan only turns on now and then as the airflow is increased. Im sure PLA or PETG...
thingiverse
This is a custom PSU cover remix for the Anycubic Chiron, fitting a 120mm fan. I did not design this, no credit for me. Someone in the International Chiron Support group on Facebook shared this. ...
thingiverse
Here is a quick adapter I made up to add cooling to the PSU. ...Carefull where you put the screws that you don't poke anything on the inside. What you need Two m3x10 bolts and nuts One 120mm Fan
thingiverse
So i was searching to buy a new fan to mount inside the psu but i had a 120mm pc fan laying around and found a mount for the original Ender3 PSU (https://www.thingiverse.com/thing:3359622). However the Ender3 Pro comes with the Mean Well PSU which...
thingiverse
120mm PSU fan for the very popular 30A 12v supplies. The fan over hangs the PSU so is only retained with two screws. You will need to tap out the 6 M3 screw holes. I personally feel fans work better when blowing so thats whats ive gone for. ...There is...
thingiverse
An adapter that lets you mount a 120mm fan to the back of the control box / PSU of Wanhao Duplicator i3 (Monoprice Maker Select V2).This makes the control box quieter and keeps it cool during printing. Version 1.1 (Nov-8-2016, Recommended version)...
thingiverse
This spacer is designed to increase the clearance between the 120mm PSU fan and the Z-axis roller bolt for the Ender-3 printer. After printing a popular cover on a PSU with a 120mm fan mount, I got a problem - the X-axis beam cannot move freely...
thingiverse
Simple adapter for 120mm fan for KP3S PSU. Photos are taken from prototype. I made few changes afterwards for better fit. If you have bigger printer, you can print just only one part and avoid using screws. To connect a fan to a board use step...
thingiverse
This is a remix from the "Ender 3 Pro PSU Cover for 80mm" fans, because bigger is always better...and I had only 120mm silent fans around. ... Also the Cover is adapted to have the airflow channels at the top, because hot air goes up ;-) Fusion...
thingiverse
Pure Wings 2 fan, but should work with other 120mm fans as well. Overkill for sure, but I already had these fans on hand from an old PC build. Remixed Terminal cover as well. https://www.thingiverse.com/thing:4774312 note. Due to the extra...
prusaprinters
Pure Wings 2 fan, but should work with other 120mm fans as well. Overkill for sure, but I already had these fans on hand from an old PC build. note. Due to the extra height feet risers are required. ...I used these...
thingiverse
... the piece was too fragile (printed in PETG at 100% fill), next time i will make the walls thicker. The fan holes was too small... for usage with Ender3 PRO PSU, is needed to cut as seen at the images.** I have a dremel and saved the printing...
thingiverse
It allows a 120mm fan to be installed in replacement of the small noisy stock fan. I am using a Cooler Master Pro 120. It has RGB LEDs I then tied into the string already mounted on my printer for extra cool factor! I printed at medium speed...
cults3d
It allows a 120mm fan to be installed in replacement of the small noisy stock fan. I am using a Cooler Master Pro 120. It has RGB LEDs I then tied into the string already mounted on my printer for extra cool factor! I printed at medium speed with...
thingiverse
There were a few other fan mounts, but most were thin or designed for the mean well. All the screws should line up and the screws for fan are counter sunk. The holes for side screws are a little small and need to be reamed out. ...It should make for...
thingiverse
I created this to fit a Noctua NF-F12 120mm 24v fan on the Tronxy X5SA power supply. ...This considerably lowers the PSU fan noise (as it's almost completely silent now) and increases the cooling efficiency of the PSU.
thingiverse
That's mine version for mounting 120mm fan on Ender 3 PSU. Mounting holes for fan are drawn 2,8mm, you should use M3 screws. If your printer don't handle hole dimmensions you can drill them witm 2,8mm drill. Mounting holes for PSU are not existing....
thingiverse
Your bed has to be at least 245 x 120mm to print (Supports Tevo Turantula Large bed) **PSU Setup** * 1 x PSU Cover * 2 x M3*12mm Screw (To screw to PSU) * 1 x [Rocker Switch (KCD3)](https://is.alicdn.com/img/pb/270/936/666/666936270_416.jpg) (rated...
thingiverse
This is replacement cover for 30A PSU (S-360-12) that fits any 120mm computer fan. You are doing this modification at your own risk. Please unplug power supply from wall socket before making this modification. You will need to remove original...