1968 firebird model

This is a set of models, minus one piece noted in the instructions, for a minimal cutting body modification kit for the Adventure Force Commandfire by Dart Zone. Print instructionsForward I am not the most advanced 3d printer user. I printed these...

Now, everything will just fit without removing the box insert.ModelQtyDescriptionquacks-chip-box.stl2Boxes for Red, Green, Blue, and Yellow ingredientsquacks-chip-lid.stl2Lids for those boxesquacks-misc-box.stl1Box for the miscellaneous ingredients...

In order to stay within bed size, put your skirt 0mm to the model. Once printed, remove the support material and clean up with sandpaper. Step 2: Print 2 Simple Metal Spool axle holders, same Splic3r settings as above. You can print both of them on...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

**This is demo model meant to portray the scale and detail of the helmet itself** **For the full separated files as well as assembly videos, you can find them here** https://www.aguilarworkshop.com/product-page/scout-helmet-w-attachments Major...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

--------------------------------------------------------------------------------- Print Settings: • Ensure the model is orientated as shown in the slicer image • Skirt - Yes • Skirt Line Count - 2 • Skirt Distance - 1 mm • Support - Yes • Support...

V1 arm is fine too, but there's a risk of collision with some models of the head in very rare cases of high and wide prints. Prepare all parts. Power off the printer. Unplug the power cable! Disconnect the low voltage connector (2 wires). Unscrew...

The casing has a channel modeled in the side to accommodate the ribbon cable coming out from the Raspberry Pi. 3) Insert the smaller end of the ribbon cable into the Raspberry Pi Camera Module, then place the module into the view port. The view port...

First, I modeled the front of the display to fit the RepRap Discount Full Graphics Smart Controller. Then, I also decided it needed a back to protect the circuit board. Easy peasy! Next, I tackled the problem of mounting a TFT35 touch screen...

This is a procedure to prevent the bottom part of the model from collapsing. (a.k.a. elephant foot)  7. Nothing is attached to the top of the Z-axis frame yet. Do...

See Latest Updates Below ----------------------------------- * The latest model now appears at the top due to rearranged pictures. I wanted a unique look for my 4x Santa figure, if that's feasible... Took various elements from multiple 4x...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

This is a stepper motor-controlled model turntable designed for 009 but compatible with short N gauge locos (loose the fences). The bed is 100mm long, and the Arduino code will follow in the coming weeks. Primarily designed for DCC++ JMRI CMRI...

If you need to use a different pump you can model and print your own adapter as it is just a rectangle block with a hole for the pump water outlet. The inlet block should be 80mm tall and 32mm wide minus half a millimeter for fit tolerance. If you...

These are mainly meant for kitbashing digitally, so they might not work with existing citadel kasrkin/cadian models without a little work. For torsos I suggest Planetless Trooprs by LoggyK, these were the main inspiration behind the packs. Storm...

If you break a ring, simply print another.\nWhat you get\nThis model includes four sets of finger sensor carrier rings, one for each finger. The rings are worn on the first and second joint and hold a polyimide-coated Flexpoint flex sensor with its...

Please note that this model doesn't include the hooks on the bottom for the external antenna coupling. My car doesn't have one but I think it can be added easily. You can find the assembly instructions in the print instructions or here at...

After studying what was available, I started modeling my own. The problem was that most of the projects were on console tables, but our table is held on two rails, one on each side. Initially, the project was implemented on a seven-string polispast,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

MAJOR UPDATE [2017-05-05]: New and updated models were added based on suggestions and requests from people who have printed the terrain set (thanks abchiptop). Work log checked off... Checked all decks to be same dimension (5mm thick) - [x] Checked...

Stereographic Projection based on the excellent work shared here: https://jasmcole.com/2014/11/01/stereographic-lampshades/#more-650 I used Blender's "Solidify" modifier to add various thicknesses to this model for printing. I recommend printing one...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

Here you find better resolution for the pictures: https://www.printables.com/de/model/501107-led-rgb-matrix-ws2812b-esp32-wled-32x32-round-squa https://www.youtube.com/watch?v=5lFdzL06OOs On Youtube there are lots of tutorials to build a 32x32...

PLA will end up sagging, and failing over time.All of these parts are oriented in the correct printing position aside from re-centering the models.No supports are needed. *The cable chain end links printed fine with NO SUPPORT in all 30 different...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

... It is not for printing, unless you have a very big printer. The Thingiverse 3D view of the STL does not work well with this model. ...I assume it is too large and you have to zoom way back to get the pivot point in a position to rotate it properly.

... THANKS! Happy printing! PS.: Thanks to Rick and Morty, who posted this wonderful ASX1 model on grabcad, which I used as the basis for my renders (and my apologies for the poor quality photos - my printer stands in a pretty dark corner of the room).

While a ring is included with the model, I don't have a way to mount it... ...Might be easier to use pipe cleaners instead maybe? I don't know yet. If I come up with something I'll update on here. Or if YOU come up with something awesome? Let me...