3 axis stage 3d models

This is z axis for Green Mamba DIY 3D printer V1.3 in OpenScad. ... more info: http://www.optolab.ftn.uns.ac.rs/index.php/education/project-base/211-diy-3d-printer printer: https://www.youtube.com/watch?v=jDCqzzHqFrU Green Mamba DIY 3D printer V1.2:...

A Gopro mount for the Ender 3 Y-axis . Includes 4 pieces: 1)The mount - requires 2x M5x16 0r M5x20 screws to fix. These just replace the existing screws holding the tensioning end cap. 2) A 50mm Gopro-compatible 90°extension. This requires...

More information can be found when you look at the other items:\r\n\r\nOriginal\r\nhttps://www.thingiverse.com/thing:140126\r\nRollie410\r\nhttps://www.thingiverse.com/thing:1895486\r\nRunCam2...

Y axis tensioner Y axis tensioner for Ender 3 pro. You can use this design to properly tension your belt for Y axis. The middle part, can be changed for different pulleys/bearings and also adjusted in left/right direction if the belt is binding one...

In the quest for the most rigid Ender 3 Pro in the land, I stumbled across this model: https://www.thingiverse.com/thing:3343666 from mlynch002 and made some changes.Changes:Repaired and remeshed modelResized Holes to M5Added flat version without...

To grasp the fundamentals of a 3-axis accelerometer, I created a custom mounting for the ADXL335 sensor. This allows me to better understand what kind of data it actually measures and returns. The three axes are clearly labeled on both ends of the...

This y-axis stabilization kit is designed for Solidoodle 3 printers, which often experience nozzle drag-induced vibrations in the y-axis, especially at the build platform's end. The problem is widespread among various printers. This kit solves it...

My Own Take On The Z Axis Anti-Backlash Nut For Solidoodle 3 With Aluminum Bed Installed This Is My Third And Final Version, I'm Very Satisfied With It I Had Some Smaller Springs Lying Around In An Assortment Pack That I Decided To Use Instead Of...

[Ender 3 V2](https://amzn.to/2MddE5f) Y-Axis Stepper Motor Damper Mount remixed from the design by: [Ra1ns](https://www.thingiverse.com/thing:4591114) to fit my specific dampers and provide clearance for full retraction of the Y-axis. My dampers:...

The hardware has impressed me so far, but an issue with the Z-axis adjustment has arisen - the limit switch occasionally misses the Z-axis stop screw. A simple solution is to add a small bumper at the end of the screw. You might need to customize the...

V2 - Changed the Distance between the Z axis and the aluminum frame made the hole bigger to compensate for low print accuracy ########################################################## Remix Summary I used the Thing...

This is a straightforward 3-axis block designed to be used with threaded rod, measuring 6mm or 1/4" in size. The bottom features a flat surface for ease of printing. Version 00 has an extremely thin wall where the holes intersect, while Version 01...

So I remixed the display camera mount and the Z-Axis Handle to one modell and adjusted the screw hole size.See https://www.printables.com/de/model/172815-ender-3-s1-pi-camera-mount for the holder and screw to mount the case or print the version,...

Since I wantet to have a Linear Rail on the X Axis of my Ender 3 without Loosing to much printspace I designed this Plate. You can use it to mount a 300mm MGN12 Rail. I had it lasercut from 5mm Aluminium for around 20€. You will need to Print the...

Human: I struggled with the standard X-axis tensioner plate on the Mendelmax 3, finding it difficult to adjust and prone to compressing the bearings, which made them spin poorly. This is a screw-adjustable X-axis tensioner designed specifically for...

I do another model for fix the z-axis, but the z-axis high does not use correctly and I change the model for fully use the z-axis hight. ... bearing - diameter 16mm; hole 8mm

I suspect this discrepancy may be due to variations between the Ender 2, Ender 3, and Ender 3 Pro. ... I discovered that a simple fix was to limit movement to east-west only, so I designed a new part based on the original Ender 3 Pro injected molded...

It also doesn't require any fiddling with the end stop.NOTE: Does not work on the Ender-3 ProAlso, check out these other mods that dramatically reduce the sound of your Ender 3X-Axis Stepper DamperZ-Axis Stepper DamperLow Profile FeetEnjoy the...

You'll need the following parts: One 5mm Bore (toothless or 20tooth) GT2 Idler Pulley Optional: M5, 5mm longer Y-axis stepper motor bracket-to-Y-beam screw. This will allow it to extend through the male bracket and keep it firmly in place. ...One of...

This cable clip securely fits onto the underside of the y-axis ribbon cable's slot within the extruded frame underneath the entire y-axis assembly.

These parts, in conjunction with a dual Z-axis upgrade kit for a CR-10, allow the Ender 3 to be upgraded to dual Z-axis using a belt system to keep the 2 leadscrews synchronised. The dual Z-axis upgrade kit comes with the plate and mounting hardware...

I'm attempting to create a better Y-axis guide for my Creality Ender 3 printer. To achieve this, I've successfully converted from four bearings to three and made the clearance easily adjustable without needing an excenter adjustment. One possible...

## Additional hardware It is recommended to use 4 m5 15mm screws to attach this mount to the Y axis profile, but a bit longer or shorter screws will work too. Stock Ender 3 Pro screws may be a bit too short. Also, 4 m4 nylon washers can be used...

Holder for shutter switch on Ender 3 V2 X-axis. ... Parts for Shutter Switch: Micro Switch:...

This is a base holder designed specifically for the Mijia 3 Axis Handheld Stabilized Gimbal, which perfectly complements the Mijia 4K Action Camera. With this innovative base holder, you can easily position it on any desktop or horizontal surface and...

Holder for shutter switch on Ender 3 V2 X-axis. ... Parts for Shutter Switch: Micro Switch:...

This allows you to view the nozzle directly, unobstructed by fans, and also enables an enclosure since the front of the axis doesn't extend far enough to go beyond the plane of the front opening. ... I've included an optional logo that I designed,...

I designed a phone holder that attaches to my Ender 3's X-axis, providing a convenient spot to place my device while using OctoPrint with IP Webcam. This universal solution is simple and effective, offering an ideal viewing angle for monitoring...

Maybe I'm doing something wrong, but on my Ender 3 v2, the Z-axis limiter sits too high when I'm not using the glass bed. I usually loosen the bolts and slide it down a little if I need to, but there is a small plastic tab that has to be maneuvered...

Here Are My Print Settings as Used on My Trusty Ender 3: * Standard Resolution at 0.2 * Supports Built In, with the Model Upright and Ready to Go * Extruder Temperature Set to a Scorching 200c * Bed Temperature Cranked Up to a Sizzling 60c *...