3.5 hdd caddy 3d models
1060723 3d models found related to 3.5 hdd caddy.thingiverse
Xbox 360 DVD delete, internal 3.5" HDD caddy
thingiverse
3.5 inch caddy for 2.5 inch drive. ...Has top and bottom part to make a full size 3.5" hot swap drive.
thingiverse
This is a hot-pluggable caddy HDD design mount, with the ability to bind multiples together. The idea is to use a Male to female sata adapter (https://goo.gl/yJS595) as the interface between the Cables and the HDD, so that it can be plugged and...
thingiverse
It's a 3 bay HDD Caddy. I designed it so they can click and be connected using the hooks and slots at either end. ...Print Settings Printer: Makerfarm Pegasus 8 Modded ...
thingiverse
By popular demand, I used my original design (2x 2.5" HDDs) and created this 3.5" HDD caddy. Xbox 360 Slim model, with 2x internal 2.5" HDDs: https://www.thingiverse.com/thing:5327826 Replaces Xbox 360 internal DVD with an internal HDD caddy. HDD...
thingiverse
A generic hdd caddy for a 3.5" hard drive. ...The caddy uses 4 standartized pc case screws like https://www.aquatuning.co.uk/media/image/af/5b/d6/94577_1_600x600.jpg You can find a generic 5bay cage here: https://www.thingiverse.com/thing:4106284 and a...
prusaprinters
The caddy uses 4 standartized pc case screws like https://www.aquatuning.co.uk/media/image/af/5b/d6/94577\_1\_600x600.jpg You can find a generic 5bay cage here: https://www.thingiverse.com/thing:4106284 and a customized 4 bay cage for the Thermaltake...
thingiverse
I inherited a desktop computer that had a small drive cage inside that could hold 3 3.5" HDD drives. However, it did not have trays for drives to fit in, and I couldn't find any to print. So, starting with the design by @isolt as a start, I modeled...
prusaprinters
Adaptor to secure 2.5" disks in 3.5" disk caddies. ...I have tested this with Dell and Supermicro caddies.
thingiverse
hard drive adaptor to fit a 2.5 inch SSD or laptop drive into a 3.5 inch desktop PC bay just added mk2 which has holes for mounting flat :) hope you find i useful Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: Doesn't Matter...
thingiverse
Most Rackable Systems HDD Caddies sell for close to $20. This one takes about 90 minutes to print, and uses less than a dollar of filament. ... No screws are needed as tabs on the model attach to the HDD.
thingiverse
This is an universal hard drive caddy for all common 3,5 HDDs I used mine for an Dell FS12-nv7 Storage server. ...
thingiverse
Wanted shorter drive sleds/caddies to reduce print time. As Chrisddr77 also found, some drives don't have the middle screw holes. ...In my case it was a couple Seagate Exos X14 and X16 drives.
thingiverse
hard drive adaptor to fit a 2.5 inch SSD or laptop drive into a 3.5 inch desktop PC bay + Mac Pro grille Thanks oad_master45 .
thingiverse
... screw holes. ...Only the screw holes on the ends. So, I added the last set of screw holes to make the design compatible with all 3.5 inch hard drives. You can find the Generic HDD Cage for these Caddy's here: https://www.thingiverse.com/thing:4106284
thingiverse
20% Infill Supports everywhere You may find the the holding knobs are a little too tight depending on printer tolerances. If so, file them down slightly. Designed so it sits slightly to the left for people (including myself) who are using an...
thingiverse
This is remix of the original file: https://www.thingiverse.com/thing:858533 Which had the wrong scale, while using as a base the rescaled modification: https://www.thingiverse.com/thing:1607776 However the 'properly scaled' model above is still off...
thingiverse
I just simplified the hexagonal bits as the comments got me a bit worried, done using tinkercad by importing the STL and editing, before I realised Dojan had very kindly shared the source !!!! Still,it is all good practice. This has now been...
thingiverse
I just did a quick tinkercad bad remix on the original to get it to fit correctly on my setup. ...I figured I may not be alone here so uploading for others
thingiverse
For the famous (and nowaday super cheap second hand) Supermicro CSE-815 1U server chassis, I designed a harddisk caddy (hard drive tray) for 3,5 SATA/SAS HDDs. I liked the idea of https://www.thingiverse.com/thing:2413043 , but build these on my...
thingiverse
I needed more HDD caddys for my Fujitsu Celsius W510 and I made it. ...You should mount 2 screws for each caddy.
prusaprinters
For the famous (and nowaday super cheap second hand) Supermicro CSE-815 1U server chassis, I designed a harddisk caddy (hard drive tray) for 3,5 SATA/SAS HDDs. I liked the idea of https://www.thingiverse.com/thing:2413043 , but build these on my own,...
thingiverse
[X] 2.1 - Stackable (modular) HDD Caddies [ ] Rack Mounted (I have a server cabinet) (not yet done) [ ] ATX Motherboard Mount [ ] PSU Mount [ ] Rack Mount Adaptors and Other Supports 2.1 Stackable (modular) HDD Caddies As the photo shows, I have...
thingiverse
Specs: Compatible with 3.5" hard drives. Designed for bays that were approximately 0.75" tall and approximately 4.25" wide. Thickness is approximately 0.1" . Standard (counter-sunk) HDD case screws should work great with this. ... I've listed the...
thingiverse
Customized version of https://www.thingiverse.com/thing:1595628 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1595628
thingiverse
Remixed https://www.thingiverse.com/thing:858533 HDD adapter to slot into HP Z600 workstation 5.25 bays
thingiverse
A tested toolless 3.5" HDD Caddy for Cisco UCS M3 Servers 2.5" adaptor included
thingiverse
You can use it to install 2,5" SSD Usage: 1) CoolerMaster_HDD_Caddy_35to25.stl - use this one to install a 2,5" HDD in the main Tower 2) CoolerMaster_3.5_to_2.5_tray_SWITCH.stl - use this one to install 2,5" HDD to the switchable boot devices down in...
thingiverse
It's a common hard drive caddy to screw your 2.5" hard drive to 3.5" mounting desktops. If you print it, please leave us a comment with your thoughts. UPDATE: As stated in one comment below, to align properly HD cabling now V2 its mirrored in X...