3d characters models

I added some build notes below and a BOM which doesn't include screws, wires, connectors, etc., but has all major components. I planned to revisit this model and release a better version. However I have at least a year's worth of projects in...

Particularly VERY IMPORTANT you need to change the setting from the default Negative Image to Positive Image. Adjust the Model Settings as I have shown in this Thing images. The Size (width) MUST be 150mm. Also I suggest reducing the thinnest layer...

 I have it installed on both my printers and it's really nize.MK3S and (+) versions of the adapter are unique to each model and not interchangeable.Both adapters drop in over the screw heads as shown and get trapped between the extruder body and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

The tubes used for processing in the Whirlwind would end up leading Ken Olson to transistors, which led to the transistorized TX-O (the love of many a tech model railroad clubber) and later to Olson founding DEC. Suddenly, the Whirlwind was the...

A custom-made enclosure specifically designed for the Raspberry Pi computer assistant Assistant assistant A bespoke casing tailored to fit the Raspberry Pi device. assistant Created especially for the Raspberry Pi, this is a one-of-a-kind case. ...

 You may have to insert a custom hole for a usb lead depending on your mounting position, this could be done in the model, or via a drill after printing.You will need to do some tweaking to keep the led matrix against the grid.  This can be...

And Happy Printing!-------------------------------------------------Originally designed in Fusion 360 and printed with Prusa Mini+ THIS MODEL IS UNDER CC (Creative Commons) LICENCE. Note: The DO NOT EAT sign might not print properly due to...

# Introduction This is a remix of the Ender 3 HallON v3 Installation kit to fit a Micro Swiss Direct Drive set-up (recent models with additional screw holes on the left. Because I noticed that the hold of the sensor in the adapter gets loose after...

You can find a somewhat more detailed list of supplies in my Instructable at https://www.instructables.com/Kissing-the-Frog-V20-Back-Horn-Bluetooth-Speaker-F/ Basically any combination will do (as long as the driver is 3.3" or smaller so it fits the...

The “NANO 1” model follows (support for matrix / hemera already published). in addition to the name and logo (grant it to me) they share the same "SUPPORT BASE" component as a fixed base, and with the quick release (only 2 screws) to adapt in the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

If you decrease the size of the model, you will end up with less than 2 layers which might decrease the integrity of the maze. You should be OK increasing the size, but the maze walls may not fuse in the middle using 2 layers. You'll need to...

If you are using ceiling pipes, I've modelled the right side of the pipes only. For the left side it will need to be mirrored in the slicer. The vents part is optional but I recommend glueing it to the roof. The vents piece can act as additional...

Update 2021/02/06: Upgraded parts- steering arm 2.0 Bump steer reduce for steering knuckle 2.0(the ackermann angle have been reduce on steering knuckle 2.0 and therefore with the change of geometry this part is required to reduce bump steer) Update...

If you have a tuned in printer, bump the speeds up a little for a dramatic improvement, (make sure wall thickness is a multiplier of your nozzle thickness - The parameters are important and there are a lot of dependencies, Make sure you have done the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

Cable clamps bolt to the Extruder mount bolts to keep the cabling tidy, which I've not used yet as I can currently only run 1 of the heaters at present (my A20M control board is a V4.1 model which doesnt have the components fitted to allow for dual...

It features several small niceties, such as a water inlet that optimizes top-water removal, using magnets instead of suction cups, a 'vacation' mod for skimmer waste overflow, snap-on piping for secure fitting, and much more.Please note that this is...

Theoretically, it can run more than 11 hours on 1 load (not tested). What parts do you need?Plastic parts:You can use the print files if you have an MK3S or you can use the model files and set everything up yourself. The photos show the position...

The airflow is higher than stock and the Draken due to its duct design but it has more channels.The main point of developing the Gripen next to the Draken is for printing models that need less but more controlled cooling, meaning it cools from all...

 900mm in length (shown in the picture is a bit too long, you may want to use 800mm instead)The bamboo skewers seems to come in different sizes, so use the file that closest match the skewers you have and scale the model accordingly.  If...

The retainer is up higher than need be in the video for safety.--------------------------------------------------------------------------------------------------------------All parts printed in PETG, with standard Voron settings for rigidity.0.20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

Deck furniture is always a good way to add interest to a model. You might want to install a waterproof switch somewhere on the exterior to save having to unscrew the whole deck every time to turn it off and on. Enjoy sailing your Pocket Boat,...

# What you'll need This will work with any CH340 USB-serial chip I think, but the model here is for the CH340N for USBC. A picture of the exact chip is given. I ordered one from AliExpress for about $3, and one from eBay for about $6 (because it was...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

They should easily fit even on small printers; if you can print Hadley, you can print this mount.The mount uses a vinyl disk that sits on top of teflon pads, for very smooth motion.It is very lightweight, and can easily disassembled for compact...

the older model this was printed from did not have the pockets for the hex nuts so it was threaded directly into the plastic instead. Ive uploaded a reinforced version of the arm that should work better with heavier controllers.i also opened up the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...