3d model scanner

I've seen some Hedron models before, but none of them were quite right to me - they got the patterns wrong or just looked off in some way. So I set out to design my own, and this is the final result. Well, these are the final results because there...

To assemble: Note - this is a somewhat challenging model to assemble, with a lot of parts, and a lot of tight-fitting pins to hold the parts of the toy together. You may also have to clean up a lot of support off the oddly-shaped pieces as not much...

unless you have a special edition like a Porsche, Mercedes, or older Audi, VW, or BMW model, which is what I have. For most of these special editions, the original push bar won't fit. I found a design on Thingiverse called *Klein-laui* and tested...

The handle houses the controller with its user interface and no base unit is required.All that is missing to be the perfect soldering solution for workbench and mobile needs is a stand and a housing.Introducing TStationThe TStation is a case for the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_overlap = 0 custom_back_extra_port_corner_radius = 5 printer_tolerance = 0.4 stencil_pattern_element_radius = 6...

You will, however, need to modify the hole in the motor arm to fit your motor's shaft, after you have scaled the model. You may also need to do some modification to the connector arms so that they clip nicely to the connecting rod that you plan to...

Fits both "Research" and "Research Plus" models.Don't loose precious time with clips or carousels!Print your holder now ;-)Materials required4mm aluminum rod (2x 18cm minimum)2x M5 20mm screw with hex head2x M5 butterfly nut2x M5 washerSuperglue or...

(The toothbrush still shouldn't fall out, but a hole any larger and it might...)(I also use a print of the original model as a holder for fine detail paintbrushes, so a hole in the bottom of that one would be rather pointless.)Enjoy!Print...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

One uses a buck converter that is very difficult to find at the moment, so this model is not uploaded. This is the one I use. The other one has a larger area inside so you can fit other converters, should you want to. You can ignore the converter and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

It has been almost three months in the making, and several bits are an additional 100–200 sketches beyond the base model, which means there is a ton of Mf-detail, I probably overdid it. My goal was to create something special for kitbashing,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_top_outer_edge_chamfer_radius = .6 stencil_vertical_position = 50 use_mouse_ears = 0 custom_back_camera_x_size = 23...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_x_size = 30 custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30...

 V4 was still a solid design, but I made some very subtle changes based on my range outing last weekend where I was using it on a handgun.The Magnetospeed Sporter chronograph has some mounting limitations compared to the V3 model, so I wanted to...

[Medium Sized Model - 25mm Base] [Presupported in 32mm and 75mm scale]   One of the few Colossals on Tharador not to be born in the bitter Frozen Wastes of Oldavor. Harmara is also one of the few hemomancers to exist out the bounds of Oldavor, the...

THIS WILL NOT WORK WITH THE HID GOLIGHT SPOTLIGHTS (GL-3XXXH-X models). If you purchase this transformer with any of our Larson Electronics lights, we will make sure that the connectors are a match.Features: The DCP-25-DP 256 watt converter features...

**Update October 26, 2017:** Since I was messing around with the model anyway, I figured it was time to do something I've wanted to do for a while. To decrease the "stack height" on top of my inexpensive flexy tripod, I slapped an 18.5mm ball clamp...

Shroud to complete the FGC-68 do you need to select the Shroud that you like these come in 3 models N (no top rail) TR (with top rail) LR (lower Top RAIL) Link to shrouds FGC-68 Top rail shroud set paintball magfed...

The battery negative is connected straight to the Anderson PowerPole negative and the radio negative.The model includes a plate to put on top of the batteries to ensure nothing gets in and shorts them out.To make the antenna fit inside the box with...

If you have a dual-extruder that can print dissolvable, or you just want to go for printing with supports, check out his remix of my model! OTHER PROJECTS: Another day, another project. If you like Space RTS games, check out our latest project on...

Reference photos http://ww2german.com/flu1694.html Reference data https://archive.org/details/Tm9-1901/page/n89/mode/2up https://bulletpicker.com/pdf/TM%209-1300-203,%20Artillery%20Ammunition.pdf#page=262 You can edit this model here...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 0 custom_corner_resolution = 8 stencil_drawing =...

Initially I modelled the candle I wanted, then using boolean operations subtracted it from a cube, and split the cube in half. ...Then I added the pins and matching holes just to help align the boxes and hold them together a bit by padding and pocketing...

This helps with the strength of the threads as it will be printed length wise on the build placeThis gives more freedom to place pieces in any orientation, as well as add spacers between larger parts for more accents and individualityFixed stringing...

It is possible that a future will make and upload a model of that piece. In the meantime, if anyone knows where to get suitable pads, please let me know. As I was saying, I started to hang them on the screw. Since the surface of the screw with the...

... list of Remixes. If I have missed something please advise me and I will correct this ASAP. If you do not want your Thing as part of this collection please advise me and I will remove it and try to include an alternate Thing for the missing model.

* Supports: Yes (if using Cura we recommend using the [Tree supports](https://support.ultimaker.com/hc/en-us/articles/360012614559-Experimental-settings) option and adding a 'Brim' to help the Tree supports adhere to your print bed) * Rafts: Doesn't...