3d model topology

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

... The models are in the position, they should be printed. No support is needed. I suggest to use a 10mm brim for the tube to prevent it from detaching from the buildplate while printing this tall piece. Printed on an Ender 3 Have fun!

It is possible that a future will make and upload a model of that piece. In the meantime, if anyone knows where to get suitable pads, please let me know. As I was saying, I started to hang them on the screw. Since the surface of the screw with the...

My Fusion 360 CAD model has 0.09mm of axial clearance so the printed threads should effortlessly spin together. Extruding over 0.09mm will make it extremely difficult to twist the nut and bolt together using fingers, so just reprint both parts with...

# Anet AM8 motherboard case This case is inspired by a [YZ Case for Prusa made by Carter](https://www.printables.com/pl/model/1910-yz-case). This case is prepared for mount on the Anet AM8 modification frame. It can hold Anet A8 v1.7 motherboard...

After sanding the putty flat, paint it using model paint or cover it with a large sticker to conceal any imperfections. Test fit the Laforge diversity module into the hole where the old receiver used to be. Cut off this standoff because it's...

READ BEFORE PRINTING!This is a non-commercial print, this means you are not allowed to sell files or prints of this model.______________________________________________________________________________________What is this?A modular tripod/handle...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 1 stencil_size = 40 stencil_shape = 6 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

They were sold to me as "boat nails", feel free to substitute them for something else and adjust the model accordingly. For the spark gap I used a couple of bits of single stranded wire, these can be substituted for something else, multi-strand...

I first encountered the idea for this type of robot in a biomedical article, presented as a potential new candidate for exploring the human colon due to its simplicity and ability to navigate confined areas....

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

Presupported in 32mm and 75mm scale [Medium Model Size] [Statblock included in our 5E Campaign: Divine Awakening] The last child of Minera to rise from the ocean depths as a great landmass. Tharador is the smallest of all continents and most meager...

If you want to save time while testing, you can print the included **calibration test** instead of the full model, but that is optional. Once the egg halves are printed, screw the threads in and out repeatedly to remove any stray particles. It...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

phone_model_customized = Yes, it is now set at 0 custom_left_port_y_position_disabled = No, has been set by the default of 0 as requested above bottom_port_corner_radius_customization_enabled = Yes, now has a custom setting equal to 5...

** FUSION360 and STEP Sources are included **** I have my printer into an enclosure and, to save the electronics from excessive heat, I've designed this model to enclose all the electronics at a singe location. These were my requirements: -...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

Then, once the mount is installed on the handle, you can unscrew the bolt and increase the distance from the magnit to the sensor, increasing it enough so that the brake sensor only activates when the brake is actually applied.The model is made in...

You will, however, need to modify the hole in the motor arm to fit your motor's shaft, after you have scaled the model. You may also need to do some modification to the connector arms so that they clip nicely to the connecting rod that you plan to...

The extruders are mounted using the same procedure.Made with Onshape:Source CAD: Snapmaker Artisan Modular Side ShelvingPrint Recommendations:Print in PETG for the increased strength.Rotate the models so they are laying down, bosses facing up.Print...

What fun! To build an adapter to your requirements, install Blender v3.80 (or later) and open the T2M42atapter_pre_assembly.blend file. Select menu View | Front (or press number [1] key on the keypad) to view the model from the front against the...

  I've been using the one in the picture for a few weeks and apart from not looking as pretty with the cam open, there's absolutely no difference in performance.I think I have allowed enough room to print this model with a .6mm nozzle but if you are...

and Pause Layer = 2. How I Designed This Print on Window Screen This model was designed to have the printer paused at ~1mm to have the screen inserted. I made sure I made the frame thick enough to allow for multiple layers to be printed on each side...

Print Settings Printer: Heavily modded Craftbot Rafts: No Supports: Yes Resolution: 0,15 or 0,20 mm Infill: 33 or 50 % Notes: Print both models in PETG with 3 mm thick walls and slightly hotter than usual, this should give you enough strength for a...

The Doors Pack includes 47 models (each in .stl and .obj format, making for 94 files) and adds a treasure well of different doors to make your dungeon unique. It is also the first expansion pack I got ready to publish. Some of the doors come in...

The current model is sized for a 28mm long motor, if you get a longer or shorter one a new set of files will have to be generated. If you do not have access to Inventor let me know and I can generate the files for your size...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

also know with ESC if you turn power off with pot turned to high you have to turn the pot down to be able to start motor again (must be a ESC safety thing) Machine drilling a board the failed to drill completely through on the CNC PCB Mill ( My fault...