3d print dwarven forge

I would make the cable length to reach from your pants pocket to your goggles, or your shirt pocket, whichever works for you better. PS: If the LiPo buzzer is too loud stick two pieces of bubble gum into holes of little speakers, that will make the...

(ALL OF THE ABOVE ICONS ARE ALSO SOLD SEPARATELY ON MY PROFILE.) (MIRROR THE ICONS FOR USE ON THE RIGHT SHOULDER PLATE SO THE ICON IS FACING FORWARDS AS INTENDED, THIS CAN BE DONE EASILY IN ALL SLICERS) These models are designed to be fitted atop...

I designed and printed this handle to fit the motor connected 3 18650 batteries, push button, mounted all of that and got a nice small low rpm cordless drill. Low rpm drills are needed in many cases for example for drilling wood and plastic. If you...

The final versions here have been modified after I printed the original parts but they didn't fit well due to shrinkage. I've reprinted all the parts successfully at a 2.5 - 3% increase in size for ABS. UPDATE 14/10/2019 Just got my hands on a...

Use a thread lock on the bottom 3 screws to prevent them from vibrating loose and insert them into the remaining 3 bottom holes and tighten until snug Printing I would strongly recommend a filament that is UV stable so that prolonged sun exposure...

I did a filament change part way through the print to green, to allow for the highlighting of the symbols, my call-sign etc. Finally, using this layout, there is plenty of space under the top panel at the front, under the LCD / VFO area. I am now in...

Less than 2 minutes later, it was up to temperature, and held the temperature through several 2 hour prints without problem. I also tested with the fans at 100%, and 240 degrees, and it had no problems getting and staying at temp. The "box" part...

When printing the lower air duct, I did not use support inside of the duct itself; instead, I used some outside. Internal walls are designed to eliminate the need for support which would be difficult to remove. The duct on the extruder holder...

I aimed to keep the list of printed parts minimal by developing a two-gear system instead of a more complex scissor extension arm. A unique feature of my design is the guide wheel that supports the tracing gear to keep it level and prevents it from...

They bite into the print so you can just tighten them fairly snug. If you tighten too much they will strip and you'll need to use a nut but I've used them for years without having to mess with the screws after I got it set up how I want. ... And I...

Printing in vase mode on a delta printer is quite a nice thing to see. Unfortunately finding one that matched exactly what I needed was tedious. I therefore decided to learn openscad in order to build my own general customisable low-poly vase...

Other Projects Tamaguino http://www.thingiverse.com/thing:2120692 https://alojzjakob.github.io/Tamaguino/ Website Traffic / Like Monitor with NodeMcu http://www.thingiverse.com/thing:2286288 Print Settings Printer Brand: Wanhao Printer: Wanhao...

Print all parts as already oriented with no supports. You will need 2x 'Tronxy X5s belt aligner wheel'. You will need; 2x M3x6mm bolts (for bottom mounting) 2x M4x30 bolts (for belt aligner mounting) 2x M4 nuts (preferably nyloc) (for belt aligner...

Generating Attributions log: [0] Thing Title : Cover for Flashlight [0] Thing URL : http://www.thingiverse.com/thing:882 [0] Thing Author : wizard23 [0] Thing Licence : Creative Commons - Attribution - Non-Commercial [1] Thing Title : Harmonic Drive...

I was constrained by the size of the rotary switch and the USB breakout board otherwise it might have gotten a bit smaller. See it in action: https://youtu.be/PTTVuVUZYM8 I have included the OpenSCAD file which is somewhat parametric. Print...

I printed mirrored left and right (screw and wall bracket) so that the unwinding of the coil does not lead to the tightening of the retaining screw, but the screw remains in its position due to the slight resistance. I put a round piece of foam...

Optional spacers can be printed to ensure proper spacing between GLCD circuit boards as mounting screws are tightened. An optional rear panel cover is provided for use with the GLCD case. The case has holes for up to M3 hardware, but it's intended...

The holes for the banana plugs and the iron holder are not included in the file, but they can be easily drilled after the print is done. I have not taken photos of the inside cause it is pretty crowded with wires but if anyone is interested i can...

I configured the K-factor of linear advance feature to 0 in firmware, and it's necessary to configure it before every print in start G-code using a value of 0.7. I'm using this start G-code in Cura: M140 S[first_layer_bed_temperature] ; set bed...

Blocks with other angles can easily be modeled and printed if needed. It should be noted that the complementary angle to the one shown on the gauge can be mitered by placing the material against the other face of the miter gauge. The shooting...

The attachment itself is designed as a two-part unit for easier printing without supports, with the lower part serving for connecting the battery (it is possible to choose a version for Makita or Parkside batteries) and the upper part forming the...

I designed and printed this custom enclosure for the sensor using a Wemos D1 mini board (a clone will also work) and a DHT22 module. The DHT22 module, thanks to its built-in sensors, can detect the surrounding environment's temperature and humidity...

Hello.I need to “repair” my 1080Ti fans because they started to make some weird noises and low the rpms, temperatures go higer, and… why no temperature and noise reduction upgrade ?First I want say the photos are of the first functional prototype,...

Files with FDM are modified to print better with filament printers Set 04 - Generals and Staff - FM Bluecher in several poses, plus a few generals and other staff officers Set 05 - Misc. Officers - Many Reserve and Landwehr officers wore regulation...

This inner step, which is the distal 5 mm length of the pin, allows insertion of 1.75 mm printing filament, to lock the pin. The pin itself is split with a .75 mm horizontal slice, so the pin can expand when the filament is inserted. The...

  My will at first was to provide to the community affordable and easy to print by yourselves nameplates for the games who require generic tagging : Bloodbowl, Warcry, Warhammer Quest... And to help some makers adding a personal touch to their...

Print the screw and base. I used 2 perimeters but it doesn't matter much. If you want to have this on the hotend moving around, lighter will be better. PLA and PETG will both work fine. 2. Disassemble the original sensor, and push the little...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: snapAxisSlack = 0.5 GENERATE_CASE = 1 baseFrequC0 = 17.4517 noteAlpha = 3 musicAxisHolderH = 2.4 crankDirection = 90 GENERATE_CRANK = 1...

Hello everyone, I've successfully converted my MegaTronXY X1 into a CoreXY Printer with an impressive printing area of 400x450x370. After learning about the remarkable speed of CoreXY printers, I decided to give it a try and upgrade my machine. So, I...

You will need these parts printed:1 Case (any variant, read below for info)1 Cover1 Angled Stand (any variant, read below)5 Potentiometer Cap (you can put a tiny piece of filament or a drop of paint in the small hole to make it easier to see how much...