3d print elephant

In addition to printed parts, you'll need: * **16x** M3x10mm or less screws for MKS board, mosfets, and top cover (4x for each) * **1x** 80mm or 120mm fan if you want active cooling (strongly recommended) * **4x** M3x8mm or less screws for RAMPS if...

I also had a print with significant layer shift which makes me wonder if the cooling of this setup is not enough for some reason. Maybe the fan was too close to the board to allow for good airflow? Maybe it was already too close to the back panel to...

The lip on the housing measures 7.8mm wide and 1.5mm high. Secure it in place using double-sided tape. A huge thanks goes out to Core3D.tech from GrabCAD for providing the f3d file. https://grabcad.com/core3d.tech-1 This model, created by...

The lamp used in this setup is an Aglaia 4W LED touch-control lamp featuring a clamp base that was removed to accommodate a longer M6 x 20mm screw for mounting on the printed bracket. The non-conductive material of the bracket prevents electrical...

The holes for the banana plugs and the iron holder are not included in the file but can be easily drilled after the print is complete. I did not take photos of the inside because it is pretty crowded with wires; however, if anyone is interested, I...

This is a Starter and his Command Box extension for the 22RE Toyota Engine (https://www.thingiverse.com/thing:644933)The video of the finished project : https://www.youtube.com/watch?v=Oly5FVFVWa0 Print instructionsPrinter: Geeetech A10Rafts:...

It is very easy to assemble and if you print an array of this devices you can have a grid for domestic use or outdoors activity like in a camping etc. This wind turbine device is a part of a further open turbo-machine system based in a pending...

Print for four wheels 40 [roller from ab86uk](https://www.thingiverse.com/thing:3118584) and my two wheel halves 4 times each (2 identical halves = 1 wheel) in STL orientation in 0.2 mm and with 25% infill. Support is only necessary for the recesses...

I doubt it will work on other 8-tooth spools, but it doesn't take long to print and find out. Using it is pretty straightforward, but I'm going to go into detail anyway. Besides, it gives me the opportunity to play with some of "Markdown"'s features...

It has nearly the same density as Earth, but smaller and uncompressed. This is because is has a comparatively bigger iron nucleus. Mercury is sometime consider the prototype of an iron planet, a planet composed mainly in iron. Its rotation is...

I am modifying the original glass print bed to a fine-machined aluminum cast plate. I purchased this here: and used kit 4 with GFK/FR4 plate 1 mm and flat clips. Here is a brief description of the process: 1. I removed the four adjustment wheels...

I would not fly this rocket on an A motor for obvious reasons. I recommend the following print settings:Nose cone - 4 perimeters and 5% infill. Rockets are more stable in flight with more weight higher up. Tail assembly - 2 or 3 perimeters and 5%...

To achieve this, you can adjust your printer using the following template: https://www.thingiverse.com/thing:5413456 It allows you to adjust the feed rate specific to your filament to obtain precision of the order of a hundredth of a millimeter,...

The whole size is the only change.3MF- Two Colored: If you can print in multiple colors, use the 3mf files, which also use 6x2mm magnets.LinksLinks are Amazon Affiliate links.Magnets (300 count) - 6x2mm - https://amzn.to/3SswN0N Magnets (400 count) -...

Our design is nested and compact, which means it takes less time to print one set. The board we use makes wiring and assembly more accessible. With an internal battery charging circuit, you don't need to remove the battery for charging. To control...

For printing I just made everything 50% Gyroidial infill, with ESUN PLA+. Did a bunch of pretty serious drop and smash tests with early iterations and the unit held up pretty damn well. I got the makita mount from somewhere a while back but cant...

In Cura, you can place two models together and print them simultaneously by turning off Preferences -> General -> Automatically drop models to the build plate. This feature is essential for stacking the gears. Let's use our previous example to...

Using TMC2130 drivers ([plus my other modifications](https://www.thingiverse.com/glabifrons/collections/glabifronss-anycubic-kossel-mods)) with this hotend and Klipper firmware, I was able to print 400mm/s with fairly nice results (very minimal...

Even if you don't need the extra space for the switch, I recommend printing the v2 version because it has a better grip, especially if your hands are as big as mine. Arduino Code #include "Keyboard.h" #define KEY_LEFT_GUI 0x83 int herramientas[6]...

Assembly Once all the pieces are printed, start by running the wire through the hole in the center disc of the inner_reel so that equal lengths are protruding on either side. Thread the wires through the holes in the upper_half so that the wire on...

The gray and orange caddy shown here was my prototype and a number of improvements have been made to the design since it was printed, mainly regarding the fit of the deck boxes, keys, etc. The largest dimension on this is 9.7", with the height...

After a restart, the MMU will be connected or disconnected.I had to replace the power wires from the 2 pole connector to the Einsy as they were too short for my box.The support of the two connectors is screwed to the frame in the 2 already existing...

Use a screwdriver to adjust the tensioner, and with the mirrored version, you need to pull the filament lever to access the screw.Screws neededTool:Buttonhead or cylinderhead4x M2.5 x 6 or M2.5 x 81x M3 x 30 or M3 x 28 (For the mirrored version you...

Depending on the size of the equipment to be inserted in the box, it may be necessary to print more or less intermediate parts: "Body". The assembly is done by 3 threaded rods of 4 mm in diameter and 6 acorn nuts (3 at the top and 3 at the...

I also made the spacer shaft shape wider so it is not as hard to print, nor as fragile to handle. I also eliminated a few of the sizes that I felt were not necessary. --- This is a PPC (Pixel Pipe Clip) spacer tool that will help you accurately...

Note: There is no room for the extruder heatsink with this design, but I've yet to find it offers any real cooling advantage or dust protection in my mild printing environments. The extruder cooling fan has to be removed as well, although I haven't...

* As an alternative, you can print the nosecone I've now included with this thing. 20% infill should be fine and it will weight the nose without gluing on nuts. There is a recess in the nosecone for the knot from the shock cord to fit. This nose cone...

During printing the holes can sometimes be narrower. Therefore it may be necessary to drill them out. Take one thread and make a multiple knot at one end and then pull the thread through one hole. Place the top ring with the bottom side facing up. At...

It doesn't cost you anything extra, but helps me out a lot :) Print instructionsCategory: Decor Summary This is a laser cut cube with a dolphin pattern on the front face. Behind this pattern is a frosted piece of acrylic, which gives a very nice glow...

Tevo Parts used: All extrusions 3 Nema 17 40mm motors GT2 Pulley and idler Flex coupling 6x Wheels Leadscrew MKS Base 1.4 board Things I had to add myself: 2nd leadscrew 2nd flex coupler Z pancake stepper 2 smaller wheels PSU (Got a laptop supply)...