3d print led diffuser

... any surface with screws or nails. I may explore a way to use these to make a suspended version of the dispenser. Nota3: don't mind the colors. I ran out of black PETG during the print and had to switch to white. ...In the end it's not that bad.

Edit 08/01 - Hey everyone, just as a heads up, this was designed to be the same size as the 'traditional' walker named after a type of battleship but after printing it myself I realize its a little bit bigger then I thought it would be. For...

Wrong way to do this as i didn't remember that you can't print white.So i re sanded the face and sprayed all the Light color. The water slide decal paper worked fantastic, Apply decals and swipe with a wad of paper towel. The clear letters of the...

I used these from Amazon: https://www.amazon.com/uxcell-Lathe-Round-Solid-Length/dp/B07KY8SB6J/ref=sr_1_4?dchild=1&keywords=1.5mm+steel+rod&qid=1627516594&sr=8-4 (1) After printing, drill out the holes in the iron rest, the sides of the case, and the...

Let me know if this was a good enough job that you would be excited to see more from me, and feel free to send requests I highly doubt this would print well with any other printer than a resin printer. I do not have supported versions of the files,...

The fireplaces should print without supports (hopefully !). On my Ender, I tried with and without supports; the version without was easier to clean up, and the small amount of looping I got was mostly hidden or (for the stone fire surround) actually...

Middle section should be printed and then glued to the insert, once dry thread the EL Ribbon cable through the guides, I believe two are a little more stubborn then the rest but angle them slightly and they should pop through. Double back the ribbon...

It won't work as printed without additional machining. When I ordered the tie rod ball joint pack set from Robotdigg (DR001) I discovered it came with two different types of ball ends. Since most carriages and assembly plates are 40mm width, I...

The issue was that after a few prints, I had created a really cool "Rock". I wanted to be able to share the wonders of this illusion with the world, so I needed a way to present it. Did you know that "Necessity is the mother of education"? Armed...

It's essential that the fabric has a medium-sized print, or the fabric pattern may not match the image of the doll. Tilda dolls are usually carried out in a compact size, so it's best that the fabric is not too large. Dolls Tilda can be sewn two...

This can be inserted in a 6 inch flexible duct tube (used for outgoing ventilation) to prevent paper towels and the like from being sucked all the way to the inline duct fan (stalling it and requiring disassembly of the ducting to extract the paper...

This is a Custom-Made Starter Box for the 22RE Toyota Engine https://www.thingiverse.com/thing:644933 My completed project can be viewed at https://www.thingiverse.com/make:692499 # Print Settings 1 x StarterBody1 : Layer:0.15mm Raft:no Support:no...

https://www.thingiverse.com/thing:3589645 Problems: checksumme error while printing from SD-Card at TFT32 #Deutsch# Adapter für Bigtreetech SKR 1.3 zu Anycubic I3 Mega Firmware is for TMC2208 2.0 or higher with UART (ohne Filamentsensor...

Print nose with supports everywhere and 20% support density. Also use 20% support density with support brim, support roof, and support towers enabled on the LID. Use four walls and 20% infill or more on the nose, and 40% on the LID. The lid also...

Using an M3 tapered tap, I found it was relatively easy to slowly do this with no pre-drilling.The thread will, of course, not be complete and that is why a long screw is used in fixing.Assembly:Two M3 nuts should be pressed into the back of the...

Changes I made to existing models: * Removed cable tie bump things because they're unnecessary and just add to print time. * Added holes on the Raspberry Pi panel so you can zip-tie extra Z cables in a service loop. * Changed the PSU front panel to...

I'll update this when my print finishes. The Fly can fly from any position to land on any bug that that your opponent placed, moved or flipped on their last turn. This includes bugs on top of a stack. It then moves one space down into an empty...

It is though that below the ice in the surface it is a liquid water ocean, and it was early speculated that this ocean could hold life, with the geotermal heating from the tidal interactions with Jupiter and the other Galilean Moons (Io, Ganymede and...

The lip from the housing is 7.8mm wide and 1.5mm high. Use double sided tape to attach it.   Thanks for the f3d goes to Core3D.tech from GrabCAD https://grabcad.com/core3d.tech-1 for his KW11-3Z modell...

https://www.ebay.com/itm/3mm-Coupling-Motor-Rigid-Flange-Guide-Shaft-Coupler-Motor-Connector/232597820268?ssPageName=STRK%3AMEBIDX%3AIT&var=532004818119&\_trksid=p2057872.m2749.l2649 3mm 2x 18350 battery...

return(point_index_1) print(calculate_position(2.4,-5)) ``` I've assumed you have numpy installed. You might want to make this a bit more efficient with more accurate methods like KD-tree for spatial search. The data given in your example can be...

# BMG V6/Dragon directdrive mount CR10/Ender3/TevoTornado Remixed from the most rugged, solid and best performing direct-drive mount, credits for the original design go to @VykkuF (https://www.thingiverse.com/thing:3747412) ### Features * Redesigned,...

Here's how to assemble the drill: First, print all the necessary parts using a 30% honeycomb infill and supports only if needed. I recommend adding at least a 10mm brim to the body part. Next, get ready your metal parts and motor. You'll need to...

I highly recommend printing these with PETG rather than with PLA. Also, the magnets can be difficult to insert. Use a flat thick metal tool placed over the magnet while pressing down with your thumb. It's designed to be a snug fit so that superglue...

 The cutter tool is flush with the MK3S(+) printer.If used without mount, has some small areas for magnets inside the compartment so that you could attach to anything else (like a refrigerator magnet)Exterior of mount has openings on each side...

To prepare for printing in STL format, I plane-cut the bottom of the model to make it level. I exported Moses in various formats, hoping that the texture map would be copied intact. So far, only the DAE file achieved this; the PLY and OBJ files...

It's essential to print this component in HIPS or a similar material that's more heat-resistant than PLA. I've tested it with PLA, and while it works initially, it deforms and becomes brittle over time. Additionally, the cooling duct was designed for...

... or peat swell pots stand is rather warm than cold compared to glass or metal. Print parameters for me: Infill 10% Layer height 0,18mm Speed 60mm/s Speed 1st layer 20mm/s Outer contours 3 Translated with www.DeepL.com/Translator (free version)

As printed it the adapter should be a reasonable fit on that bar; if it is too tight to fit or adjust, clean the large hole with a round file or sandpaper, or put a 5/8" cutter through it. (I used a 5/8" Forstner bit, backwards - thread the shank...

Generating Attributions log: [0] Thing Title : Cover for Flashlight [0] Thing URL : http://www.thingiverse.com/thing:882 [0] Thing Author : wizard23 [0] Thing Licence : Creative Commons - Attribution - Non-Commercial [1] Thing Title : Harmonic Drive...