3d print playstation controller

Would you like to learn more about creating prints featuring OpenForge designs? Please refer to the License FAQ for further details. OpenForge has shifted towards patron support, with contributors utilizing their provided resources to develop higher...

Medium Fidlock Upper for the Traceur By ChanceMore info about Traceur from the Designer;"Picture a Worker Nightingale.Now give it a bigger battery.Now make it take Talons, Kodas, and Tachis.Now make it hit anywhere from 80 to 180fps.That's...

I also made the spacer shaft shape wider so it is not as hard to print, nor as fragile to handle. I also eliminated a few of the sizes that I felt were not necessary. --- This is a PPC (Pixel Pipe Clip) spacer tool that will help you accurately...

... professionally done and designed to remove beautifully (provided you have dialled in your printer settings). They are guaranteed to give you one of the best printing experiences you've ever had! Are we allowed to use the term "printgasm"?! ...:-)

You may print out and use any settings desired, while 2_Upper_center_font defaults automatically to write/Letters.dxf if user forgets specify a preferred alternative. 2_Upper_center_size equals fifty-four with two spaces from upper edge due being...

You can do finer adjustments to the tolerance by putting some scotch tape or masking tape on the inside of the shell wall. Print the shells with the flat bottom on the build plate at 0.3mm layer height. You might want to add a 2 or 3 mm brim to...

###Note: For better print quality all screws holes in the Cover (and also above the nuts holes in the main body) are covered by thin layer (0,24mm). For better understanding please look at Cover in your slicer (level +24 mm). ...Just use drill or...

##You will need: - two MGN12 linear rails 400 mm long with MGN12H blocks - about 16 M4 hammerhead T-nuts (quantity depends on the required rigidity) - the same amount of M4x12mm flat head countersunk screws - about 16 M3x8mm socket head cap screws...

Document description: This design is divided into two parts: core and shell skin; The shell part is open source and can be modified at will to add personal identification; The core part can be modified and adjusted according to your own needs, but...

if your endstop position of your head is in the lower left but the print area starts 20mm to the right and 20mm up than you need to set this: ** **#define X_MIN_POS -20 ** **#define Y_MIN_POS -20** **#define Z_MIN_POS 0** **Enable EEPROM settings**...

Use one stepper for Z ## Proposed solution: Print: * 1x back_nut_mount * 3x KP08_608_Mount I spent around 30 minutes assembling it and another 30 to level my bed (hopefully the last time). ### Shopping list: 1. ~1200mm GT2 belt loop 2. ~100-600 GT2...

if your printer doesn't make solid prints and the little plunger breaks off inside your slide that's your issue!! *** ** UPDATE 06 09 2021 ** Added a version that uses the original spring from the outer barrel. You can buy these separately. ...

I never printed outside the heat bed (300x300mm) although this printer could do much larger than that. Also, it took a lot of space and it was not portable at all. So a new printer design came into my mind. This printer has everything Big DIY Printer...

This wasn't an issue with the stock hotend, as its use of the default mounting points would keep everything stable, but as the E3D v6 is meant to be supported only by the hero me itself I noticed a change in print quality for the worse. What I...

To build the gate and install the metal mesh, you have to print two times the stl called "Lateral_rejillasV2.stl" and put inside (like a sandwich) the mesh. You have to stick it with glue. Then, there is another part, called "Holder.stl". You have...

Mi sembra di avervi detto tutto.Buona stampa._____________ Kitchen Sink Carpet Hi, this is a simple but functional drainer for kitchen sink.Why did I do it?Being in quarantine for COVID 19 like everyone else, not being able to go out to buy it, I...

The biggest part is 118mm x 141mm, so this can be printed on way more printers than the big version. There are now two LEDs per segment instead of three. There won't be much documentation as it's basically the same thing - just a bit smaller. So if...

=========== Arduino Nano 33 BLE with Headers [ABX00034] by Arduino Learn more: https://www.amazon.com/dp/B07WXKWNQF/ref=cm_sw_em_r_mt_dp_79YQCE5D0Y090NFVS3JH Round Refrigerator Magnets, 100PCS 6×3MM Small Cylinder Fridge Magnets, Office Magnets,...

Now have fun printing and installing the brackets. A little tip: Use heatsinks with thermally conductive adhesive and not with the adhesive pads. These are no good. If you like my design please show it with a like or a make here on Thingiverse. Die...

(hence the name Duo, eh?) Addition parts you will need. 2 - 808 (MATEcam) cameras - either a dissaembled keychain version or the DYI version (here are some links)...

From strength and flexibility, PETG seems suitable as the print material. While PLA can also be used, it is hard and brittle, so it may break easily or cause problems with the fit of the nose frame. Initially, I thought of attaching paper to the...

Due to the adhesive discs on the wind turbines, a print bed with at least 210x210 mm is required. There are 5 different lids. With NabeTest you can adjust the bearing seat of the wind turbines with scaling in X and Y. The labyrinth ring is glued to...

I took the original part and modified to make it a little simpler to print and also design. There is draft in original part in two directions of the part for molding purposes. I removed the vertical draft but kept the fore-aft draft (which is...

https://www.thingiverse.com/thing:3107686 Ich habe diesen Laserkopf von Cloudray:...

Take a look at my hinged cable organizer to manage those pesky cables as well: https://www.thingiverse.com/thing:4640618 Copy and customize it on Onshape:...

Every part is designed to be printed without supports. All the electronics and extras I used are listed below. I had to scale the parts up by 2540% in the slicer. 2x Boss 4" Speaker Driver...

For screws, you can use either two nuts per leg (one above and one below the printed hole) or M3 threaded inserts. I designed the screw holes tightly so that M3 screws alone are usable, but be aware that adjusting the screws multiple times will...

Instructions 1 - Print both halfs 2 - Insert desired weight in lead into the pockets. weight in the back will make the lure running shallower, weight in the front will let it run deeper 3 - cut a toothpick and use 2 sections where it doesnt taper...

So that fits best.DO NOT PRINT IN PLA! PLA can't withstand the summer heat.</p><p>&nbsp;</p><p>#############################################</p><p>Ich mochte den originalen Becherhalter für meine E-Klasse nicht, also habe ich mir einen eigenen...

This was started on my Monoprice Select Mini, hence the size. Video Here: https://youtu.be/Ofxbj3s3f3A Print instructions You will probably have to do a little sanding or filing to get the parts to fit smoothly, but not much. I used thick CA glue to...