3d print record

The front face of this version prints separately because of overhangs that would cause trouble otherwise. Four 2 mm holes help with alignment when gluing the front face to the main body. I designed this with IBM PC's in mind for MS DOS use just to...

So the only other way would be just to have a spring cable out of the back, but you still would have to be careful not to rotate it too much as the cable would wrap around.If anybody is interested in me creating a fully functional version than please...

... The clips should move smoothly otherwise they will not grip the eyepiece very well. These were printed with support, but designed to work without it. If you encounter any issues, please let me know. ... Arsenal's website is arsenaLproducts.com

You'll also need a 2, 3, and 4 mm drill bit to clean out the holes unless your printer prints perfect holes. Drill out the holes carefully; I used my fingers for the 2 mm holes on the case. Use the Bed Triangle part to mark the two holes to drill in...

Human: [Update 2019-07-01] #Don't print this as of now, at least with PLA After some days of usage I've noticed the spine parts and/or assembly are not sturdy enough. The combined weight and dissipated heat from the components (around 250 W under...

Refer to the link below for more information and print file(STL). https://surplusperson.tistory.com/801 If you found my designs useful, please donate what you think it is worth to my paypal.me. Your donation will be useful for a new housing...

PARTS NEEDED: Front Wing: 2x M3x12 (to mount the wings) 4x M3x8 (to mount the endplates) 2x M4x12 (from the stock front bumper, to mount the front wing mount) Rear Wing: 4x M3x12 (to mount the swan neck mount) 4x M3x12 (to mount the wing onto the...

Print the surfaces 6mm thick. ...50% infill PETG This chain roller fits a lot of Yamaha Dirt Bikes and ATV's: Part # 30X-22178-00-00 Yamaha Motorcycle 2009 WR250F - WR250FY Frame Yamaha Motorcycle 2013 WR250R - WR25RDC Frame Yamaha...

To be printed in ABS or ASA to resist bad weather -o-o-o-o- Porte d'entrée avec passage à 25% - 50% ou 75% pour tout type de ruchette Dadant 6 cadres. Le modèle présenté sur la photo est celui avec ouverture à 25%. Choisissez le fichier STL selon...

Additionally, I printed 13 [quick change](https://www.thingiverse.com/thing:1996091) pen thingies for my use. Since I utilized ultra fine point sharpies, the lid didn't work as intended. Therefore, I've included the STL for my custom lid in the...

First, print the elements before covering them with foil. I used aluminum tape typically used for sealing air conditioning ductwork; you could also use a thin sheet of metal for the element. For either design, holes are included to enable multiple...

It has been a while since I printed and fitted it to my printer, so I cant exactly remember if I needed extra fasteners, I know for Shure I needed 10x 3mm plastic screws for the bottom panels, and 4x M2.5x6 for the raspberry pi, but I think that's...

During printing the holes can sometimes be narrower. Therefore it may be necessary to drill them out. Take one thread and make a multiple knot at one end and then pull the thread through one hole. Place the top ring with the bottom side facing up. At...

10x2.5mm for backplatesome wires AssemblyPrint all partsOutherCase: after the gcode export from prusaSclicer I applied the wood pattern with the python library from MoonCactus with the following settings:...

And I'm happy to report that with these boards, I've had zero read failures from the SDCard on any of my three printers, and they've logged many hundreds of hours of printing.\nI believe I can safely claim they have completely resolved my SDCard...

Print top.stl, middle.stl, bottom.stl, and 4 pin.stl. Refer to the exploded view and attach pins through precise holes in these parts for robust construction. There are some special steps you need to follow here: 1) You may find it useful to...

For this, you will need a few parts: EzStruder direct drive or bowden doesn't matter Low profile motor support printed part (see my thingiverse thing) 30x30mm Fan shroud v3 (or other thingiverse thing version) 3 fans of 30x30mm (or different size,...

Refer to the link below for more information and print file(STL). https://surplusperson.tistory.com/818 If you found my designs useful, please donate what you think it is worth to my paypal.me. Your donation will be useful for a new housing...

I also appreciate pictures of your prints too. Thanks ;) NOTE: A new V5 lightweight and mini version is available from: https://www.thingiverse.com/thing:4850894 LEGAL DISCLAIMER: This device is designed for adults. Long term wear can suppress...

## NEOPIXEL MOUNT For the mount, I quickly printed it out of PETG, pressed the NeoPixels in, and soldered them together. The warm board stick will into the mount, but to be extra safe I slathered the back with some hot glue. ## HOTEND WIRING ...

Install Klipper and make use of your Pi's processing power to speed up and improve your prints. There is a [good guide on reddit](https://www.reddit.com/r/klippers/comments/kj2h5r/stepbystep_guide_for_ender_3_v2_klipper_w_bltouch/) for setting this...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   ...

I printed about 5 of the sleeves to get the lettering just right and included the gcode so you can get the best quality settings without trial and error. Included are 2 different back covers: one solid and one cut for a 40mm fan (shown in red setup...

This sculpture combines elements from this image and the side view in this article. This sculpture was created with Sculptris, and I'm eager to hear how it prints out or any feedback on improving its printability. These tiny hominins were discovered...

You’ll need to print the following and its best to fit in this order: If running the V6/Dragon carriage mod then fit the cable retainer and cable into it first, skip this step if you’re not. I’ve included a few options you could use: Cable...

After puting up with a leaky milk pourer until it fell apart and after finding replacements were expensive and just-as-poor-quality as my old one, I decided to print my own, in just 3 parts (plus a store-bought o-ring): * Body/Bottle * Screw-top *...

# Print Instructions: Be sure to use supports for the wall pin and the gun holder. Take care to clean the supports and leave a smooth finish on the gun holder. I set this up so the gun points to the right to hide the screw holes. If you want to...

This transformation enables my DaVinci to print PLA at 80mm/s with impressive accuracy and minimal noise, eliminating the screeching sounds associated with fast movements. Travel speed has increased to 200mm/s. This mod necessitates that Repetier...

Printing info: Felix printer was used Resolution : .15 layers and higher Supports needed. 100% infill for a heavy tool that needs durability at its core Assemble these pieces easily: - Lay the 'slider' in 'lower body' (feet towards...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   ...