3d print sound wave

40mm to secure the diff cup onto the crown gear.The pictures should help with the assembly.The gears and axles should be PETG the rest can use PLA. I will use 6 couplings in the design: 2 will power the 2 diff boxes and 4 will drive the...

I never printed outside the heat bed (300x300mm) although this printer could do much larger than that. Also, it took a lot of space and it was not portable at all. So a new printer design came into my mind. This printer has everything Big DIY Printer...

It is the low-poly and easy to print version of ionic, doric and corinthian columns. Doric and corinthian columns are supportless, only ionic column has some easy to clean supports. Just like chess knight is not photorealistic and just symbolic, goal...

To achieve this, you can adjust your printer using the following template: https://www.thingiverse.com/thing:5413456 It allows you to adjust the feed rate specific to your filament to obtain precision of the order of a hundredth of a millimeter,...

This was printed on a Flashforge Guider II with high-quality settings, so the tolerances are good, but I also allowed a 1/4mm tolerance between parts, and at this level of quality, it gave me a good fit. Painting it used acrylic spray, primed and...

The front face of this version prints separately because of overhangs that would cause trouble otherwise. Four 2 mm holes help with alignment when gluing the front face to the main body. I designed this with IBM PC's in mind for MS DOS use just to...

youtu.be/LYm1B4P_h8A The two-layered planetary system of the "quick print" version was also only intended for calibration and demonstration. As you will find, the planet gears will twist under load and the clamping force will be quite limited. I've...

It really helps to get the belts nice and tight.Here is a link to my BOM, please be aware, this is a scalable design and adaptation may be required, so get more fasteners than you think you need. Parts that needs to be printed more than once is...

Make sure to set the ON and OFF milliseconds to the recorded time from step 1.Solder the led ring:GND > GND5V > 5VData In > digital pin 6Solder the buzzer:GND > GNDPLUS > digital pin 10Solder the relay (Make sure to make the relay detachable using...

... if people want to play around. The hinge spacers could easily be added directly to the hinge (import into OpenSCAD of spacer and jiggle around) but I'd already printed the hinges when I spotted a spacer was required with this panel mounting system.

Everything is designed to print without supports. This project is a work in progress, but current state is usable.Spool Assembly:Attach tie to desired slot. I have found the slot opposite to the hanging hooks tend to position the cord ends in a...

PRINTING INSTRUCTIONS: See below. ASSEMBLY AND OPERATING INSTRUCTUONS: 1. Slide the upper part onto the press die side handle as shown in the photos, as far up as it would go. Mark hole positions, drill and attach the upper part with the press...

Print for four wheels 40 [roller from ab86uk](https://www.thingiverse.com/thing:3118584) and my two wheel halves 4 times each (2 identical halves = 1 wheel) in STL orientation in 0.2 mm and with 25% infill. Support is only necessary for the recesses...

I'm creating a modular table game that doesn't require dice - you simply print the pieces and cards. The game involves building a spaceship from its most basic beginning to an interspace station with many inhabitants and resources to manage. It's...

It is one very easy print.This version works and is complete and tested. I put in hollow tubes in many locations so you can put electronics how ever you prefer, inside, outside. Lights in buildings or Christmas tree.update...

#### What you need * The three printed parts * A cheap green laser pen like [this one](https://goo.gl/8AaT9K) (others could work the same) * 6 x M3 screws (I use 16mm, I think 12/13mm is great) Cost: less than 5€ .. Not bad ;) #### How to use it ...

A custom DIY rear light for the Patton.I wanted a solid red light on my Patton that didn't blink all the time and also increasing the visibility overall so I designed this mount for a 5V neon led strip which doesn't require data just positive and...

Hobby Tool Holders This is an initial set of compact hobby tool holders the purpose of which are: Short term tool storage for tools being used on an active project Organization to help keep the bench cleaner To help facilitate rapid tool acquisition...

I'm already making progress on the headers, which allows me to try multicolor printing. More updates will follow soon. Please check out the last picture in the gallery for more information. The design supports compact tool heads, and all...

BASIC PRINTING INSTRUCTION FOR EACH PART ARE IN THEIR NAME FOLLOWING THIS LOGIC: [model name (base if common to most][part name][helpful assembly info, mostly left or right][ (need support) if needed][how many are needed if more then 1] Unlike my...

Endstops The Y-Axis endstop is a single mount for both front and back switches, activated by two tabs mounted under the bed with M3 screws, nuts, and printed M3 T-nut converters. The upper Z-Axis switch is clamped to the Z-Stepper motor RHS...

...Both parts are easy to print without support structures. For reinforcement, the part to which the pool pipe is attached with screw clamps has a reinforcement. The hole in the container is approx. 45 mm and was actually drilled for the rubber sleeve.

Button is planned to be wired to a TeensyLC to trigger display on/off by hitting the keyboard "pause" key, and should be printed in TPU. Inner button shelf is sized to fit a 12mm x 6mm https://www.adafruit.com/product/1119 meant to hit the mapped...

I added a ziptie location for the cables (break off the designed-in support), modified a ton of tolerances, got the fan ducts adjusted to the proper height with the nozzle, made a permanent BLTouch mount, embossed "CR-10S Pro V2" and "Micro Swiss...

(Dynamic input) Short cut keys:- Ø Ctrl+A : select all Ø Ctrl+B : Snap on/off Ø Ctrl+C : Copy objects to clipboard Ø Ctrl+D : Dynamic UCS (DUCS) on/off Ø Ctrl+E : To change isoplane in isometric Ø Ctrl+F : Osnap on/off Ø Ctrl+G : Grid on/off Ø Ctrl+H...

It is a simple flat top that can easily be printed upside down and has an included thread to put in a typical Bowden tube fitting. Please the picture and the model for more information.March 7th 2023 Update: Looking at the design I realized the hot...

Every part is designed to be printed without supports. All the electronics and extras I used are listed below. I had to scale the parts up by 2540% in the slicer. 2x Boss 4" Speaker Driver...

i printed mine at 0.16mm layer height in PLA. Assembly Order:Before begining, test everything out of the case. You may need to cut the casing on the drive cables in order for them to fit 1. Attach Raspberry pi to Pi Mount: I used m3 screws for this,...

... change the experiment or further the idea. If this is a younger group, this could be done in discussion instead. Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator (5th Generation) Rafts: Yes Supports: No Infill: 10% Notes: 2 Walls

Not counting shopping and printing time, this project took me about an hour and a half to complete. Thirty minutes of that was just waiting for the silicone caulking to dry completely. Everything I bought came from stores near me, but the components...