3d print thumb splint

... to others work. A full list of items used appears below, feel free to share your prints and more items to come as time permits. Original Surgical Mask Strap Retainer was created by Thingiverse user Arrow_Archer and is licensed under cc-nc.

The STLSs are up, I have validated Most of the Prints, but not the barge as of yet. I have done heavy design work on these models, however I consider them remix's due to the heavy amount of various Thingiverse parts, so credit where it is due. The...

Make sure to print two!I haven't tested if the button inserts work, but there should hopefully be enough clearance for them.1/24/2023: Added a single piece back to the file list1/26/2023: Added some new models that should work for the Y60 LCD DIY...

They print at slightly hotter temperatures. Also, consider flexible TPU filament for the lid bumpers and the washers. The resilient material offers a quieter closure on the lid, and gives a bit of conformance on the nut tightening. The bumpers...

Thanks dscarbro, that's simple and great!I also print other custom files as they are:Prusa MK3 & MK3S Clip-in Tool Storage Box from Strathpeffer3D   ...

To extend the rear arm tubes, you will need: Forward (forward): L:120mm D:15mm Backward (backward): L:130mm D:15mm Printing Information for Parts 80% PLA for power elements and 30% PLA for the rest of the parts. Setup Requirements For this...

I printed the case parts on my Auxiliary Sidewinder X1 in PETG with a 0.4mm nozzle and a layer thickness of 0.2mm. Attention: Due to the life-threatening electrical voltage only persons with appropriate qualification should assemble and use the...

Print instructions: - AVOID PLA !!!!! - Use ASA or ABS for the mounting plate, I think PETG can be no-go if you has high temperatures in your case - Fan top, plates, etc… can be PETG - Use supports un fan top. - I put some antiwarping tabs on...

... Because in nearly every religion, love and forgiveness are good qualities that help society. So happy spring, everyone - wherever you may be. Much love. PS - Print these in the most ridiculously bright colors before you toss them into the fire!

... professionally done and designed to remove beautifully (provided you have dialled in your printer settings). They are guaranteed to give you one of the best printing experiences you've ever had! Are we allowed to use the term "printgasm"?! ...:-)

... different position on my D9, and I'd appreciate feedback on that. Also, there's a chance for the duct to almost touch the print surface when you have a very short heatbreak. ...So, don't install your all-metal hotend on the topmost position.

After print is complete the battery will not fit right away. You do want a snug fit. Most definatly do not want it to go flying out of the case while using it. Take a paint stir stick and super glue some sand paper to the stick and sand paper the...

Printing without support is required for this fan duct. Secure the fan with 2 M3 x 10mm screws and attach the duct to the carriage using 2 M3 x 25mm screws, with nut traps built-in for additional tightness. All measurements are in mm. #Response...

# BMG V6/Dragon directdrive mount CR10/Ender3/TevoTornado Remixed from the most rugged, solid and best performing direct-drive mount, credits for the original design go to @VykkuF (https://www.thingiverse.com/thing:3747412) ### Features * Redesigned,...

#Installation instruction: ##Hardware: Print, sand, use some hot glue to attach the screen to the shell and to glue them together. ##Software: Requirements: none for standalone version www + php server - in my case Lighttpd + PHP on Raspberry Pi 3+...

Bill of materials: Printed: 1 x CASE MAIN 1 x CASE FACE Bought: 5 x Banana sockets of different colors (https://item.taobao.com/item.htm?spm=a1z09.2.0.0.67002e8dUgkbaW&id=561956389062&_u=52q9f1426ddc) 1 x Potentiometer 50k Ohms...

I printed the waterwheel with an SLA printer because it is easier to get a smooth axle and a balanced waterwheel. The wheel runs slower if it is mounted the wrong way round. So the water runs onto the underside of the blades. I kept the bottom of...

I found in using my original printed design that the holes didn't allow for the kind of seasoning dispersal that I prefer (lots of it!), so I increased the hole diameter from 2mm for each hole to 2.75mm. This should allow for more or larger grains to...

The V3 STL is the plate of the four printed pieces you need. What you'll need (assuming you're using the v3 files): - A type of silicone you'll use to make this, such as the one I used because it's cheap and rated for temperatures others on the...

Otherwise you will be limited to using “dumb” USB-A to USB-C cables.Print Settings:* 0.2mm layer height recommended* Supports only holding up the top of the body, not needed elsewhere* Tree supports strongly recommended (see images)Assembly:Several...

:) My fav PLA on Amazon Italy: Tianse PLA Sunlu PLA+ GEETECH PLA My fav Resin on Amazon Italy: Elegoo ABS Anycubic eSUN Print Settings Printer: Alfawise U30 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: Tianse PLA White Category:...

Fit Ears - Pink, Helmet part 1 - White and Helmet part  - White into Helmet - Red as seen in the picture below. NOTES:The Mag Chest and/or the Mag Waist will only be able to be printed at 100% due to it using 3mm x 1mm magnets. ...Any size other than...

... In case you do not have a GT2 Pulley for this project, see the new GT2 Pulley 50T and required components. Also, see the new GT2 Pulley 76T and required components. Design printed without support... mostly... ...except for parts needing support.

... had to be enlarged to be printable at this size. Resized to 1/3000 scale, the gun barrels and some other details are lost. Printing at larger scales is of course possible, though the lack of detail suited for 1/2400 will become more apparent.

The printed part sits flush with the trailing edge. I attached rudder horns I attach pushrods, there are some guide pieces for the tail pushrods. I installed the rest of the RC gear and adjusted the controls to my liking. I balanced the plane, my...

I have included two versions of the mount, one is with the rail centered on the overall enclosure and the other is with the rail centered on the top part of the enclosure resulting in a slight (5mm) offset from center. I also went ahead and added in...

Now you can print your own frames using the same shape files used by Flite Test to cut the delrin and carbon frames.\r\n\r\nWe'll be releasing more frame designs in the future as well as free plans to go along with them. And in the swappable spirit,...

-Customizable pipe cap https://www.thingiverse.com/thing:4795549 ...this thing -Customizable Pipe Cap "Cover type" https://www.thingiverse.com/thing:5150957 -Customizable Rectangle Pipe Cap https://www.thingiverse.com/thing:4875215 -Customizable...

- Wall height specifications determine that the charger station stand at a standard elevation measuring two millimeters off ground due strictly adherence maintained through designation provided above aligning appropriately placed dimensions ensuring...

The kit itself includes: Front barrel extension (3 individual parts) Stock attachment piece (1 single part) Shoulder stock connector (1 singular part) Shoulder stock (3 separate pieces) Handle (1 individual part) Rifle scope (4 distinct components)...