3d printed dungeon

- Decreased gap to 5.4 to match the dial indicator (added 1.305mm spacer, with odd shape for printing without supports). - Changed hole to 6.53mm to match dial indicator, and made special bolt to act as a pin for a tight fit. - The hole is now 7mm...

The fireplaces should print without supports (hopefully !). On my Ender, I tried with and without supports; the version without was easier to clean up, and the small amount of looping I got was mostly hidden or (for the stone fire surround) actually...

Most PC fans should fit since there aren't any thickness constraints, if you have a thicker or thinner fan then the parts will fit around this.The fan is modular so you can print what you want and perhaps design your own parts. I've included the...

Also (constructive) criticism or exchange of experiences is welcome! Please also have a look at my designs on https://www.thingiverse.com/rolfmobil/designs and https://cults3d.com/en/users/rolfmobil/creations. under the same username (rolfmobil)......

The Stem-mount parametric model didn't produce flat sides with larger stem sizes which made it hard to print. I've updated the .f3d file so it forces flat sides. I've included two properly parameterized Fusion360 f3d models so anyone can now create...

You may also request this model printed and assembled with velcro at https://jkl-adapters.com/   **Description** To solve the tracking issues experienced by penholders while playing Eleven Table Tennis on the Oculus Quest 2, I created a series of...

(You will want to print a 3m spacer for each of the m3 screws, and a 2.5mm spacer for each m2.5 screws you use for the case. You don't need any spacers for the stand base and attachment Once assembled I set up the Pi to load my weather station...

I doubt it will work on other 8-tooth spools, but it doesn't take long to print and find out. Using it is pretty straightforward, but I'm going to go into detail anyway. Besides, it gives me the opportunity to play with some of "Markdown"'s features...

"The book The Defender, by Larissa Soehn can be purchased from Amazon.ca https://www.amazon.ca/dp/0228866030/ref=cm_sw_em_r_mt_dp_C45MY5Y5MX8X238XASPZor on...

Instructions Bill of Materials 3 or 4 - 1m OpenBeams depending on the size you want (6) 13/32" x 1" compression springs (44) 3m x 5mm screws (44) 3m nuts 1.75mm filament 4 corner open-beam corner pieces (optional for improved stability) 2 OpenBeam...

I aimed to keep the list of printed parts minimal by developing a two-gear system instead of a more complex scissor extension arm. A unique feature of my design is the guide wheel that supports the tracing gear to keep it level and prevents it from...

The lip from the housing is 7.8mm wide and 1.5mm high. Use double sided tape to attach it.   Thanks for the f3d goes to Core3D.tech from GrabCAD https://grabcad.com/core3d.tech-1 for his KW11-3Z modell...

* magnets (only needed if you also print the door brace) [link](https://www.amazon.com/gp/product/B07842PSJD) _____________________________________________ STEP files are included, but contain some parts that should be hidden, couldn't figure out...

Edit 08/01 - Hey everyone, just as a heads up, this was designed to be the same size as the 'traditional' walker named after a type of battleship but after printing it myself I realize its a little bit bigger then I thought it would be. For...

This was started on my Monoprice Select Mini, hence the size. Video Here: https://youtu.be/Ofxbj3s3f3A Print instructions You will probably have to do a little sanding or filing to get the parts to fit smoothly, but not much. I used thick CA glue to...

You’ll need to print the following and its best to fit in this order: If running the V6/Dragon carriage mod then fit the cable retainer and cable into it first, skip this step if you’re not. I’ve included a few options you could use: Cable...

Recommended Material for printing: Sainsmart TPU @ 01.mm / 210°C/ 40mm/s / no retraction Update: You can now buy my Gatehunter pod combined with the LeDrone Club Pickle frame from...

(Dynamic input) Short cut keys:- Ø Ctrl+A : select all Ø Ctrl+B : Snap on/off Ø Ctrl+C : Copy objects to clipboard Ø Ctrl+D : Dynamic UCS (DUCS) on/off Ø Ctrl+E : To change isoplane in isometric Ø Ctrl+F : Osnap on/off Ø Ctrl+G : Grid on/off Ø Ctrl+H...

Although, I honestly believe if a goofball like me can figure this out, it should be a lot easier for the rest of you. Print instructionsThe only thing that really needs support in this whole thing is the front door. ...I modeled it as if it were...

The entire box is designed such that if you print with 6 shells in your setting the outside walls will be solid, and the front wall will be double thick as it will take most of the hits. The bottom is flat, but has a large recess to allow you...

For those who just want to print and don't want to do any soldering, I created a board with sliders that won't require electronics or additional work. However, it's not as awesome. Enjoy! P.S.: I didn't get around to painting it yet (ran out of...

I printed this with pla on my prusa mini with supports on the build plate only, 40% infill, 4 perimeters. for the support settings i used: Z contact distance: 0.2mm pattern spacing: 3mm contact layers: 4 xy separation between an object and...

After checking the accuracy of fit with a test frame, I was able to print the complete funnel and fit it with two filters and mount it on the suction cup without any further adjustments. ...After the first test, the suction power is not hindered, the...

To assemble the kit, you'll need to print: 1. Base Z 2. Base XZ 3. Base Y 4. Base bed 5. Fan start link (for X) 6. Y end link 7. High B 40° link 8. 37 high B links 9. 23 low B links 10. 11 low 5° links For the Y, start with the Y end link on the...

I also added a small electrolytic capacitor to stabilize the power to the ESP32 to prevent low power brownouts, 47uf / 50vdc - More than a than...

I printed these organizers with 0.15mm layer height and the lid works perfectly - it's easy to attach and later it can be opened and closed without a problem. CARD TRAY: It is a tray with 3 sections for 3 decks: artifact, fear and item cards. A...

Preparation * Print the puzzle components * Have phones or tablets with the Aurasma app installed * Provide students with 20-25 minutes to solve the puzzle References The math involved in this puzzle is relatively simple, so no references are...

Because there are no symbols in the other three statues it is difficult to identify them, and their names are indeed a vexata quaestio; according to Raffaello Borghini (1584), what they were actually called depended entirely on the oral tradition...

This lifts the cables to eliminates contact and flexure of the cables during printing and it eliminates/obviates the need for chainlike cable housing to hold the cables and distribute/minimize flexing and possible wire breakage. ...In return, your...

... the outside of the fan instead of pressed fit inside. Hope I got those measurements correct.. This is my first remix of anything, so if I did something wrong, let me know.. I have it printing out right now, so I'll add some pics once it's done.