3d printed fidgets

This insert fits the Ark Nova base game and Marine Worlds expansion.In the pictures we've used alternate money tokens.Update Nov 9 2023: added sleeve_holder_2_v2 as replacement for card_holder_2 if you sleeve your cards.Update Nov 11 2023:Updated...

Instructions You'll need 4 of the mosaic feet, and four endcaps - each should be printed with a .3 layer height and no support using an infill level of 15%. As for me, that was enough. A 5/16" length of threaded rod will come in handy as well as...

Wrong way to do this as i didn't remember that you can't print white.So i re sanded the face and sprayed all the Light color. The water slide decal paper worked fantastic, Apply decals and swipe with a wad of paper towel. The clear letters of the...

The gray and orange caddy shown here was my prototype and a number of improvements have been made to the design since it was printed, mainly regarding the fit of the deck boxes, keys, etc. The largest dimension on this is 9.7", with the height...

I recommend printing "Re-ARM-fan-endpiece.stl" first in your chosen material, and then verify it fits the 80mm fan. If it doesn't fit, you may need to calibrate the extruder. Thanks to the following people for creating the models which helped me...

It won't work as printed without additional machining. When I ordered the tie rod ball joint pack set from Robotdigg (DR001) I discovered it came with two different types of ball ends. Since most carriages and assembly plates are 40mm width, I...

In it's current state, however, I do find the wallet quite usable.  Assembly:Print a base, lever, cash compartment, and then lid. Add magnets to the holes, being extremely careful to place them in the correct way, so that the ones in the lid actually...

And if you can't find an SVG for the picture you want, I've had a lot of luck converting them with Inkscape. Print Settings Printer Brand: Prusa Printer: MMU2s Rafts: No Supports: No Resolution: 0.2 Infill: 100 Filament: Inlang PLA Many Category:...

Every glance at this work of art will make your eyes light up with admiration.Printed in PLA or PETG, the robust material ensures long-lasting stability, giving your board a firm hold while creating a harmonious connection between window and...

... If you feel comfortable swapping filaments mid-print, try switching the white filament out for some clear filament after layer 2 can help allow more light to pass through. ## No Magnets I'm considering replacing the magnet indents with OpenLOCK.

After numerous requests, I also included the Z-probe for the Bl-touch in the gallery photos.Below is a guide with very simplified photos in Italian and English versions, and at the end of the article the settings used in print (at least for me.) Good...

... Use a straight piece of wire or a drill to poke through the holes after printing. 2. Cut three pieces of paperclip wire, each about 15mm long. Bend one of them 5mm from the tip as shown in the picture. 3. Stick the bent piece through the knob axis.

To build, just print two ears, then attach the 450mm lengths to the tabs on the ears with t-slot nuts. It should be pretty self explanatory. m3x5 screws should do the trick, but if your parts shrink too much a washer may be useful to ensure a tight...

I printed it in a black PLA to help it blend in better with the Xbox. Edit - Feb 1st '21 - I realized that the smaller file's hanger's were off centered... so I have adjusted that and re-uploaded the stl. I have also included 2 more versions of...

BOM: the printed part 1/2 wavelength of solid 6ga copper ground wire (plus a little for trimming) coaxial cable coaxial connector for your cable To assemble the antenna: Cut two lengths of the 6 ga copper wire a little longer then 1/4 wavelengths...

If you want to support my work, you can contribute with me by donating to this PayPal account.Print SettingsRafts:NoSupports:YesNotes:If you set the wall width to one filament line (0.4~0.6mm) and the infill overlap to higher amount (70~100%) you...

4.) Time to choose colors for printing. Going all lime green, it looked nice because I thought this vibrant tone brought a certain brightness when laid on a dark or otherwise subdued backdrop which always helps capture attention wherever applied...

... is how we made it, it's a personal project, so it's ugly in places. I'm just putting this up here in case anyone wants to do this, or do this differently, or use it for something else. Or just print an overcomplicated Bender head, idk. ... Peace.

I printed the attachment upside down, using supports and 100% infill, since it needs to be airtight or nearly so. For the seal, I used Oomoo 30, a rubbery silicone mold compound. Other types of rubber with similar properties should also work. Once...

The GoPro HERO 6 & 7 Rubber Suit holder is a bit of a pain to print but it works and has enough room for long LiPos. ... [Check out the GoPro HERO 6 & 7 Rubber Suit here…] [HERO] [HERO]:https://www.thingiverse.com/thing:3167362 [Check out the GoPro...

Print all 3 sizes of each part. 2. Sand the barrel and rail supports wherever they will make contact with the barrel shroud, tank, and scope rail. I used 600 grit. Wipe the parts clean. 3. Install the shortest rail support. It should require...

Potential fixes might include: * a "print-in-place" design for the cap which includes a solid and captive axis pin, * replacing the M2 screw with a very small rivet (strong, but not desirable due to tooling requirements and permanence of...

Print and remove support material from case 2. Optionally, drill a hole into the side of the case to install para cord to use lanyard 3. Install Buttons and switches - x-acto may be needed to remove material from case for button to fit 4. Install...

... Button pack, for those that like the style better. These ONLY work with the Build A version, using the 1.3inch LCD The "Shims" files are thin shims you can print and wedge between your Pi and the case layers if you wish to add rigidity to the case.

*** Edit 29JUN21 *** I added : -- A plate V2 : The fan duct outlet are 20 degres tilted instead of 30 degres in first version The holes that allow the tightening of the screws are lightly closed (approx 2 layers) so that the overhang print is...

The alignment pegs print separate to make it easier and glue into one side of the base of bezel along with the magnets. I use superglue. The power for the amplifier and microphone board comes off the GPIO header. #Thank you! ... If you got...

During printing the holes can sometimes be narrower. Therefore it may be necessary to drill them out.Take one thread and make a multiple knot at one end and then pull the thread through one hole. Place the top ring with the bottom side facing up. Pay...

The case is designed for low cost electronics: * 7" AT070TN92 LCD (16:9 ratio) * HDMI+VGA+2AV LCD control board, LVDS, chipset RTD2660H * Touch Screen Panel (eGalax) Print these parts flat side down, with NO support material. Use a 0.2mm layer...

Generating Attributions log: [0] Thing Title : Cover for Flashlight [0] Thing URL : http://www.thingiverse.com/thing:882 [0] Thing Author : wizard23 [0] Thing Licence : Creative Commons - Attribution - Non-Commercial [1] Thing Title : Harmonic Drive...

Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 1 Rafts: No Supports: No Resolution: .3mm layer height Infill: 25%, 2 extra shells Instructions Parts The included file parts.pdf is a list of the parts needed, along with costs and...