3d printed honeycomb structure

Test this :) !!! Printing Info : - use a materials that is stable in water (I used PETG).- use support from build plate only. - optionally add more part cooling to make support removal more easy. Why I made it : I made this...

This inner step, which is the distal 5 mm length of the pin, allows insertion of 1.75 mm printing filament, to lock the pin. The pin itself is split with a .75 mm horizontal slice, so the pin can expand when the filament is inserted. The...

... soldering skills. Refer to the pictures for how I wired everything. Undertake this project at your own risk. If you screw this up, you could fry your boards, cause a fire, electrocute yourself, etc. I printed the files using my CR6 Max.

It's tough to find a good attachment point and still get a piece that's minimal, doesn't interfere, easily removed during servicing and has the right geometry to get light on the work effectively.Going to run with this version for a while and see how...

For this particular item, print two backs, two bottoms, one front, and three sides (H2). Slide the bottoms through the sides and push them back to lock in place. **Update 5/10/2020**: American Mini cards are now included, with a single row, two-deep...

... approximately 0.400-VDC (800-mA motor drive current). 10. This completes the repair; test using the load/unload filament utilities. Print Settings: Printer Brand: MakerBot Printer: MakerBot Replicator Rafts: Doesn't Matter Supports: Doesn't Matter

(Dynamic input) Short cut keys:- Ø Ctrl+A : select all Ø Ctrl+B : Snap on/off Ø Ctrl+C : Copy objects to clipboard Ø Ctrl+D : Dynamic UCS (DUCS) on/off Ø Ctrl+E : To change isoplane in isometric Ø Ctrl+F : Osnap on/off Ø Ctrl+G : Grid on/off Ø Ctrl+H...

I have added another screw hole to it, but haven't printed or mounted it in that configuration yet, so hopefully the glue isn't required anymore. - Cap - to cap the bench mount suction when I am using the vacuum as dust collection for the other...

I use this: Amazon link Some cable connector like this: Amazon link If You enjoyed this project and You want to say "Thank You" please consider supporting me by sending a tip on thingiverse or my PayPal here. I hope you enjoy it! Print Settings...

Designing and drawing this model required over 1200 hours of work, and printing it took an estimated 2000 hours. The model uses various colors in PLA, including True Red (10 pounds), True Yellow (2 pounds), True White (8 pounds), True Black (4...

My old wooden LED bases are simple and elegant, but now I've created one that can be printed with ease. The distance between the LEDs is adjustable, controlled by turning the outer ring of the base. This allows for a customizable lighting experience...

This is a Custom-Made Starter Box for the 22RE Toyota Engine https://www.thingiverse.com/thing:644933 My completed project can be viewed at https://www.thingiverse.com/make:692499 # Print Settings 1 x StarterBody1 : Layer:0.15mm Raft:no Support:no...

Use 5050 LED's!  BOM:12v LED...

In order to complete this build, you will also need the internals: Drive motors - 16mm gear motors https://www.botkits.com/collections/all-products/products/four-battle-hardened-motors Wheels - Fingertech 1 x 0.5 in foam wheels...

I printed the main panel in 0,3 mm layer height so I designed it to be one layer thick where the display is located. The buttons for the thermostat should be able to just push on the buttons when it's secured in place. If that doesn't work, just...

Depending on the size of the equipment to be inserted in the box, it may be necessary to print more or less intermediate parts: "Body". The assembly is done by 3 threaded rods of 4 mm in diameter and 6 acorn nuts (3 at the top and 3 at the...

Instructions You'll need 4 of the mosaic feet, and four endcaps - each should be printed with a .3 layer height and no support using an infill level of 15%. As for me, that was enough. A 5/16" length of threaded rod will come in handy as well as...

I print at: X-9.4%, Y-9.4%, and Z-10% to provide a snug fit while keeping the height. Then I attempted to put super glue on the bottom to glue it to the bottom of the keycap. It worked but the key cap choc stem wasn't long enough to push down the key...

PRINTING INSTRUCTIONS: See below. ASSEMBLY AND OPERATING INSTRUCTUONS: 1. Slide the upper part onto the press die side handle as shown in the photos, as far up as it would go. Mark hole positions, drill and attach the upper part with the press...

in die Hemdtasche stecken.(Sorry für alle die bis Mittags am 4.7.22 das Modell geladen haben da hat sich ein Flüchtigkeitsfehler eingeschlichen, Verbindung am Klipp, inzwischen korrigiert, noch zu sehen auf dem letzten Bild)Hier das Ursprüngliche...

All other cars use the same wheel. Since I dont have an existing Brio or Ikea train set, I printed all my tracks from the following project using a -7.4 mm Z offset in my slicer, so that the tracks were thin (no need to waste filament/time making...

The design is somewhat double-brick out-house in most places and doesn't require high-resolution printing, such as wafer-thin walls. However, it will produce a robust system that people may like to refine themselves. OpenSCAD files are provided to...

I printed mine at a speed of 50, with a resolution of 0.2 mm. Assembly instructions below, assembly photo above. As always, any questions, don't hesitate to ask.Assembly:See numbered photo for reference.During assembly you'll want to keep an eye on...

Less than 2 minutes later, it was up to temperature, and held the temperature through several 2 hour prints without problem. I also tested with the fans at 100%, and 240 degrees, and it had no problems getting and staying at temp. The "box" part...

... initial model was created by TigerAce1945's sdkfz 222, with possible elements from M-Bergman's 1:200 and 1:100 series. The origin of the tires is unclear. Production has not yet commenced; I typically have my models printed commercially in resin.

pass # Complete design calculation for different parameters # Design a case (function design_samsung_case is omitted in mock up) def design_samsung_case(base, shape_stencil_pattern_element_shape,pattern_radius,roration): pass...

This is the version I have printed and pictured. Will check compatibility with the Gen L board when I get a chance. Renamed files to help clarify. 8/30/2020: Added a new bottom file for the MKS Robin Nano. 6/11/2020: Added the text file instructions...

I managed to get 280mm of print height out of the stock motors, and am using 16" z rods. When assembling the new frame, flip the X axis upside-down and backwards so the POM nuts are at the bottom inside of the arm instead of the top, meaning they...

While I haven't printed it myself, it should work just fine. *** 9/27/18 *** The main litho no longer needs to be resized (I've renamed it to MainMashup.stl). The crown's orientation has been fixed, and all the parts should fit nicely together now....

I could have sanded it down, but I moved the viewport and flipped it onto the flat side so that it will print properly without too much slicer adjustment. I am removing the old lid file. The original lid file will be with the original case that I am...