3d printed hypercube

There is a printable bearing race included for the idler pulley which works well (print 2 of them). You also may want to lube the spring housing interior with a teflon based lube to allow easier sliding since sanding inside the housing will be...

The tiles were printed with natural PLA, and then welded with their bases using dichloromethane. They were washed and primed in black using Vallejo black primer through an airbrush. A watered mixture of a white craft paint, Vallejo Light Brown and...

Print Settings: - Printer: Sintron Prusa - Rafts: None - Supports: None - Resolution: 0.3 mm - Infill: 40% - Notes: No fan being used. Supports are needed for all sensor brackets. Designing this project involved combining the inspiration from...

The ball housing needs to be printed in black for it to trigger the sensor properly. The ball is a tight fit, and I use PETG filament; I press the ball in with pliers. When the filament is absent, there's a 8x3mm round magnet on the back that pulls...

Even if you don't need the extra space for the switch, I recommend printing the v2 version because it has a better grip, especially if your hands are as big as mine. Arduino Code #include "Keyboard.h" #define KEY_LEFT_GUI 0x83 int herramientas[6]...

To prepare for printing in STL format, I plane-cut the bottom of the model to make it level. I exported Moses in various formats, hoping that the texture map would be copied intact. So far, only the DAE file achieved this; the PLY and OBJ files...

You'll want to print: - 4 x clamp - 2 x wall mount - 3 x s5-s6-s7 - 1 x everything else As for the rest, adapt the instructions from the above link to complete the assembly, and modify as needed to suit your installation. (Hint: when dual-banding,...

... I have not mounted the printer, controller, and power supply on a base board, so the wires to the controller are not cut to length. It's still pretty messy, but I'll do it once I'm happy with the design and fix everything down. Happy printing.

I printed the case parts on my Auxiliary Sidewinder X1 in PETG with a 0.4mm nozzle and a layer thickness of 0.2mm. Attention: Due to the life-threatening electrical voltage only persons with appropriate qualification should assemble and use the...

For those who just want to print and don't want to do any soldering, I created a board with sliders that won't require electronics or additional work. However, it's not as awesome. Enjoy! P.S.: I didn't get around to painting it yet (ran out of...

Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator (5th Generation) Rafts: Yes Supports: No Notes: Take advantage of color families to reinforce the concept that parts combine to make the whole and vice versa. For the example set, I...

All prints must be made with a filling of not less than 80%. The knobs are available in 2 versions, one with the predisposition of the recess of the 6mm nut for the M3 screw the other to be threaded later with an M3 male. Obviously, use this...

Steps: - Print the file - Slide the PTFE into its location at the desired length - Use a felt tip pen to mark the start of the contact on the tube - Take out the tube and cut it round on the outline as on the attached renderings - Replace the tube -...

Hobby Tool Holders This is an initial set of compact hobby tool holders the purpose of which are: Short term tool storage for tools being used on an active project Organization to help keep the bench cleaner To help facilitate rapid tool acquisition...

Font Narrow Widen = No widening of narrowed characters, a setting from older designs where letters may need expansion when space runs low so as not fill too many vertical spaces in tightly stacked horizontal text columns across page; it reduces size...

The print time for this project is around 13-15 hours with a layer height of .28. https://youtu.be/-cRUheSAXM4 [Update 2] After finishing my assemblies and using them, I can confirm that the coupler I made is strong enough to handle the cleaning...

I was inspired by the [Bed Cable Side Chain mod by Whoppingpochard posted at prusaprinters.org.](https://www.prusaprinters.org/prints/54320-artillery-sidewinder-x1-genius-illuminated-bed-cab) The mod relocates the bed heater and temperature sensor...

Take care to ensure the Adapter port with the wires has been sanded to remove sharp edges & serrations from the printing process. Slide the Adapter over the motor and secure with a 2.5 to 3.6mm wide zip tie. A pair of pliers will help to pull the zip...

The two silver rings are Dekco and can be printed in PLA. The holder itself in PTEG+ for absolute stability All you need then is a bike GPS mount from Amazon. then an M5 countersunk head, a nut and a snap ring. The 3 original screws from...

I've tried increasing the print speed to 150%, no layer offset !, there's probably more to do. For assembly: I bought my motors online (MKS SERVO42C NEMA17), they were already pre-assembled and calibrated. So they could be used immediately. To...

Print the required parts (some will need supports), glue the splash guard to the top of the airlift pump as pictured, cut the mesh to size and glue through it with the mesh retainer holding it in place on the holding basket's window (superglue was...

... Because in nearly every religion, love and forgiveness are good qualities that help society. So happy spring, everyone - wherever you may be. Much love. PS - Print these in the most ridiculously bright colors before you toss them into the fire!

There is a new version of this carriage at https://www.thingiverse.com/thing:3615464 AND an even newer one at https://www.thingiverse.com/thing:3688067 I highly recommend the newest version for better rigidity and simpler printing and assembly! This...

What with trying to design mods for my printer, I figured having a virtual model would be super handy - and it got totally out of control!\r\nAs I've seen people complaining about not being able to get plans for the acrylic parts in case they break,...

... Done with Base Save as Part (*.prt) And as STL If you want to print later. The top screw Again start with a hexagon 2.5 wide 0.5 tall. Extruded base, make a circle in the middle 1.5 wide 1.7 long (This way you can be sure it screws in all the way).

If the printed parts don't want to sit flush, sand/file the lower one's small end. Realign motor pulley and tension. The idler location is a little bit higher (on purpose) to more closely match the carriage attachment point. For the Y one near the...

Medium Fidlock Upper for the Traceur By ChanceMore info about Traceur from the Designer;"Picture a Worker Nightingale.Now give it a bigger battery.Now make it take Talons, Kodas, and Tachis.Now make it hit anywhere from 80 to 180fps.That's...

I doubt it will work on other 8-tooth spools, but it doesn't take long to print and find out. Using it is pretty straightforward, but I'm going to go into detail anyway. Besides, it gives me the opportunity to play with some of "Markdown"'s features...

Watch the video at https://www.youtube.com/watch?v=tN6ngN8lytw Instructions: Part P03_Case should be printed with support but without closing USB and Network breakout holes with pillars (in Slic3r). Enable "Don't support bridges" for this. Check out...

As this model is in 1:10 scale, it is rc controllable and not a quick print!This is my second 1:10 scale “Lanz-Bulldog” tractor. Many parts are quite similar to my 1:10 scale “Eilbulldog” but I have optimized most of them. The interior is quite...