3d printed mini itx

Left to our own devices to scour the net for solutions, (clearly we weren't the first people with CR10S Pro V2's to have purchased this product...right?!?) well after printing three different models that just didn't fit my setup quite right, I got...

The result is interesting but messy, the paint settles in the layers' hollows (I printed with 0.3mm layers). Sadly, I burned the surface because I used a coarse sanding paper with an electric screwdriver, mixing the paint with the PLA.... The...

Before printing it make sure your wheel lock set is the genuine from VW (part number 000.071.597.D) and search with your hand under the seats to see if you have the 4 mm tubes -mine is a VW Taos produced in Argentina, so it may be different from the...

A custom DIY rear light for the Patton.I wanted a solid red light on my Patton that didn't blink all the time and also increasing the visibility overall so I designed this mount for a 5V neon led strip which doesn't require data just positive and...

If you still think you want to do it, I'd recommend my slot-lock attachment system as seen in TauZ and Tau brace.\r\n\r\n**Update** I redid the foot so it screws directly into motor frame which is far better and simpler to print\r\n\r\n**Update** I...

this is an afterburner direct drive mod for the "tronxy x5sa pro" currently the e3dv6 hotend and the dragon hotend are supported In Y axis you lost 10mm print space these things are needed for the afterburner: Cap screws M3x6 2x M3x8 3x M3x12 2x...

If you print and install these and your lathe breaks, congrats; you used a part that some dummy on the internet with a set of calipers and too much time (namely, me), uploaded. If you try this idea, you are doing so at your own risk. I also make no...

Here's a poorly recorded video of it running on 100mm/s: https://www.youtube.com/watch?v=GovX9jY8XzE ## Change Log 2019-05-01 * Moved the Horns Duct to a separate thing: https://www.thingiverse.com/thing:3600021 2019-04-24 * After some testing I no...

The pieces can be assembled in multiple different ways.  - Alien Desert bases: 19 different bases ranging from 30mm to 80mm, and including a desert rock scenery piece.  All the parts are pre-supported for SLA resin printing! Storyline of the...

Plug in to your pi, then expand your file system using "sudo raspi-config" There are a few ways to access your print server. Find out your RPi ip address, then type it on your browser http://printrbot.local/ My image has avahi installed, which...

Refer to the link below for more information and print file(STL). https://surplusperson.tistory.com/801 If you found my designs useful, please donate what you think it is worth to my paypal.me. Your donation will be useful for a new housing...

Update: I made a 2nd Gen hub adapter that is much simpler, prints a lot faster and seems to have held up to all the abuse we have put it through over the past week. The plastic wheels/tires on my sons power wheels didn't have enough grip even...

IMPORTANT: It is designed to be printed in TPU. I used a TPU with the common 95A durometer. It's meant to be flexible and to protect the frame so it grips in a vise properly without damaging the frame. While I was working on cutting the grooves...

Printing both pieces or separately. I have also included the .gcode files for Prusa MK3s printers. .2mm layers. Notes: The clip takes some effort to slide onto the meter. It is a bit tight. Just wiggle it a little side to side and continue...

from standard signs to oval or circle shapes Multigon shapes Triangle/Pentagon,Hexagon,Octagon up to 8 Text Lines many carefully preselected high quality Fonts Various Font Styles, adjustable Line & Character Spacing positioned freely ...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   ...

(You can use a simple arduino sketch that prints to the serial monitor when a button is pressed) - Get a sheet of foam, put a thin line of superglue across the bottom of the case, and place it on the foam sheet. It shouldn't take more than a few...

 If you're adding a rackmount device, you'll need longer screws for the ones that go through the rack ears.Smear a very thin layer of urethane glue on the faces of the corner brace, position it, and drive in the wood screws to hold everything...

... amélioré : plus esthétique (et d’autres éditions spéciales;) ), système d’éclairage led, etc. Pour suivre ces améliorations, n’hésiter pas à vous abonner a ma page Thingiverse et Facebook : https://www.facebook.com/waikikiprod Bon print à tous !

They print at slightly hotter temperatures. Also, consider flexible TPU filament for the lid bumpers and the washers. The resilient material offers a quieter closure on the lid, and gives a bit of conformance on the nut tightening. The bumpers...

I have added another screw hole to it, but haven't printed or mounted it in that configuration yet, so hopefully the glue isn't required anymore. - Cap - to cap the bench mount suction when I am using the vacuum as dust collection for the other...

 It is remarkably powerful for something this size, it will penetrate cardboard and has a maximum range of 15 meters. This is a modular design that allows you to fit which ever Prod (bow) you like they simply slot in and you use a...

When printing these models, it's highly recommended that you use Cura's "Horizontal Expansion" feature with a negative value. A value of -.12 works for me. If they are still too rigid, try -.15, then -.20, and so on. Introducing BuckleBoards, a...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   The...

UPDATE: I have reworked the top and bottom of the case so that it can now be printed without supports being turned on. I have also moved the USB and Ethernet port partitions to the top half of the case to ensure their stability when installing the...

The print time for this project is around 13-15 hours with a layer height of .28. https://youtu.be/-cRUheSAXM4 [Update 2] After finishing my assemblies and using them, I can confirm that the coupler I made is strong enough to handle the cleaning...

Later I will add photos of a finished print with some painting and post-processing tips.See the Remixes section for two other variants.-------------------------------------------------Tento bunkr, tzv. <strong>řopík</strong> (podle ŘOP: Ředitelství...

Put it in dedicated place  and then glue both parts together as it it shown in instructions below: ASSEMBLY INSTRUCTIONSPrepare desired Bottom Base (Flat or Hollowed one) and 4 Corner Columns Pour some Superglue (or one you use to bound your printed...

If it interests you, the design can be modified: https://www.tinkercad.com/things/8xbdOSIT0zA-makita-eleksmaker-mount The files include: - The face plate holds the router clamp - The mount block (lose or solid) connects the face plate with z-axis...

##Print:## - 25% infill - 3 walls - 0.1 layer height ##Tips:## - The guides on the carriage were a nice fit on the pins, but a little too snug for a smooth glide. To improve the movement of the carriage on the pins, I used my electric drill to spin...