3d printed thumb splint

small boxes used for storage - I had some space left, so I decided to go with 2 small boxes, which can also serve as a save box - 2 additional magnetic deck holders - for exploration cards, if you throw out one of small boxes you can also save cards...

to the picture).4) Zip-tie, screw or stick (doublesided tape) the gimbal controller to your plate.be careful that the m2 screw in the middle of the plate doesn't short out the controller!5) If you want print out this nice cover:...

This wasn't an issue with the stock hotend, as its use of the default mounting points would keep everything stable, but as the E3D v6 is meant to be supported only by the hero me itself I noticed a change in print quality for the worse. What I...

I printed this with pla on my prusa mini with supports on the build plate only, 40% infill, 4 perimeters. for the support settings i used: Z contact distance: 0.2mm pattern spacing: 3mm contact layers: 4 xy separation between an object and...

Plus more being added please see table belowSorry Painted in lettering and not double colour printingTaken from https://www.thingiverse.com/thing:3079639I used a draft setting, nozzle 215c bed 60c. Label ListAster American...

(I use 4 x 25mm M2 screws) For mountig my rx and vtx, i printed 1 x vtx_base.stl which fits onto the fc stack. For the rectangle standoffs you need 2 screws and 2 nuts to fix it. These standoffs are inteded to use at the left, right and rear side of...

This is the version I have printed and pictured. Will check compatibility with the Gen L board when I get a chance. Renamed files to help clarify. 8/30/2020: Added a new bottom file for the MKS Robin Nano. 6/11/2020: Added the text file instructions...

If you make one or have improvements, please post. Print instructionsCategory: Costume Summary Here is my third version of a costume prop for Tom Clancy's The Division video game. It's some kind of shoulder beacon / gizmo that all the characters...

To build this mod, you will need: - 3 three-millimeter by twenty-millimeter socket head cap screws - 3 three-millimeter by twelve-millimeter machine screws - 3 washers (twenty-millimeter diameter) - 7 #6 or #8 flathead screws (three-quarters of an...

This was printed on a Flashforge Guider II, High Quality, so the tolerances are good, but I also allowed a 1/4mm tolerance between parts and at this level of quality, it gave me a good fit. Painting it was using acrylic spray, primed and filled,...

Mount the printed spacers on the Raspberry board, by sliding them around the tubes. 6. Mount the 3.5” TFT screen on the Raspberry Pi board using the GPIO connector. 7. Mount the whole assembly on the right side of the main panel using four M3x10...

I would not fly this rocket on an A motor for obvious reasons. I recommend the following print settings:Nose cone - 4 perimeters and 5% infill. Rockets are more stable in flight with more weight higher up. Tail assembly - 2 or 3 perimeters and 5%...

... reduced earbud radius. // A smaller tab has been implemented on the slide notch for a neater design. // Minor winding slots are now deeper, and only added if there's sufficient room. // Bugfix: the issue of printing half a card has been resolved.

First, print the elements before covering them with foil. I used aluminum tape typically used for sealing air conditioning ductwork; you could also use a thin sheet of metal for the element. For either design, holes are included to enable multiple...

If a defined limit is exceeded, a signal is transmitted to OctoPi and the print is paused.Zusammenbau/AssemblyElektrische Bauteile/Electrical components:Die benötigten elektrischen Bauteile können dem Schaltplan entnommen werden./The required...

https://kc9on.com/product/fox-hunt-offset-attenuator/ ###What is what### To use this case, you'll need to print the cover and one of the cases depending on your choice of connector. FoxhuntV5C.stl has no antenna outlet for you to modify it to your...

Later I will add photos of a finished print with some painting and post-processing tips.See the Remixes section for two other variants.-------------------------------------------------Tento bunkr, tzv. <strong>řopík</strong> (podle ŘOP: Ředitelství...

Print the box STL files are at https://www.thingiverse.com/thing:2607585 6. Add the hardware Glue in the OLED display with hot glue. Cut a piece of strip board to hold the female headers to plug in the WeMos as well as a connector for the display...

I took the original part and modified to make it a little simpler to print and also design. There is draft in original part in two directions of the part for molding purposes. I removed the vertical draft but kept the fore-aft draft (which is...

Download and print the base for turf scrubber in black filament. You will need to purchase the items below to finish the build. Total cost for algae scrubber with filament is around $75. ... Acrylic on Amazon $10.00 <a target="_blank"...

The files included are: 1a) ice_cream_maker_top.stl: this is the main top section 1b) ice_cream_maker_top (no text).stl: the main top section, but without the "willrow hood" text 2a) ice_cream_maker_bottom_with_standoff.stl: bottom with rebel logo,...

... to build this wheel. FOR PERSONAL USE ONLY - NON COMMERCIAL - NOT FOR RESALE COPYRIGHT Canary Sim Wheel Designs - ALL RIGHTS RESERVED You cannot sell the digital model, a derivative or adaptation of the model, nor can you sell prints of the model.

I extruded the design to 1mm, added some fillets, and printed it in PETG. Worked the first try (instead of requiring the expected two redesigns). For those still following along, I installed the video card with the new PCIe bracket into the QNAP....

... to others work. A full list of items used appears below, feel free to share your prints and more items to come as time permits. Original Surgical Mask Strap Retainer was created by Thingiverse user Arrow_Archer and is licensed under cc-nc.

A single support (base + 2 side panels) and a nut can be printed for each spool and the spool would only be changed by releasing the wing nuts so the spool screw would not have to be removed. It'll need: -2 bearings 628 / 6-2Z (13x6x5)mm -100mm...

upload My modified MKS firmware for mks robin nano (fork mks v2.0.2): https://github.com/ochkariky/MKS-Robin-Nano-Firmware_compile (add More menu, M48, add UBL support in autolevel menu, increase length name in Print menu.) Resolves the issue of a...

It is the low-poly and easy to print version of ionic, doric and corinthian columns. Doric and corinthian columns are supportless, only ionic column has some easy to clean supports. Just like chess knight is not photorealistic and just symbolic, goal...

In the meantime I have developed this holder for 30x 1 Euro pieces so that you can just put the whole thing in the glove compartment and the coins do not roll wildly through the area.The distance of the coins is minimal from each other and the...

... the outside of the fan instead of pressed fit inside. Hope I got those measurements correct.. This is my first remix of anything, so if I did something wrong, let me know.. I have it printing out right now, so I'll add some pics once it's done.

This is accomplished by printing a column of fanned-out light pipes that radiate from the LED. Continue reading below the videos! Videos: They are all extremely short. Warpcore running at warp factor 2 Warpcore Standard from Novel Mutations on...