3d printing database

My huge thanks to both of them. Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2**Rafts:** Yes Supports: Yes**Resolution:** 0.2 mm Infill: 20% **Filament:** [ Makerbot PLA...

... initial model was created by TigerAce1945's sdkfz 222, with possible elements from M-Bergman's 1:200 and 1:100 series. The origin of the tires is unclear. Production has not yet commenced; I typically have my models printed commercially in resin.

... shape con the center of the top side). I have only checked the grids with TT685 since I do not have the others. I would be very grateful if you could publish your photos made with this grids. Do not share the model files nor sell printed grids.

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   ...

When printing the lower air duct, I did not use support inside of the duct itself; instead, I used some outside. Internal walls are designed to eliminate the need for support which would be difficult to remove. The duct on the extruder holder...

Font Narrow Widen = No widening of narrowed characters, a setting from older designs where letters may need expansion when space runs low so as not fill too many vertical spaces in tightly stacked horizontal text columns across page; it reduces size...

This inner step, which is the distal 5 mm length of the pin, allows insertion of 1.75 mm printing filament, to lock the pin. The pin itself is split with a .75 mm horizontal slice, so the pin can expand when the filament is inserted. The...

Depending on filament flex, shrinkage, and printing tolerances, your screws may extend too far into the front grid and begin to push out of the front panel. When in doubt, try a screw one size shorter than suggested.</p><p>There are two mounting...

It will be necessary to further adjust the operation of the limit switch, this is done simply, unscrew 1 fastening screw (on the Y-axis beam), move it in the right direction, and test it))) - Obvious change, worth the original FB BMG) About the...

PLA in my opinion is not resistant enough (humidity, temperature etc.) The logo and the wings are colored in orange and silver. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2 Infill: 40% Filament: CPE...

There are a few different files here: Fairmile D MGB Early - The boat as it was originally made (guns, apart from the two twin 50-cal mounts, printed separately) Fairmile D MGB - The same boat with a raised platform added amidships for mounting 20mm...

***PART #5*** https://www.thingiverse.com/thing:3379068 Are your printer full of dust and small filament pieces, well now it won' get stuck in the slots ***PART #6*** https://www.thingiverse.com/thing:3923876 Do you forget what direction to spin the...

Thanks dscarbro, that's simple and great!I also print other custom files as they are:Prusa MK3 &amp; MK3S Clip-in Tool Storage Box from Strathpeffer3D&nbsp; &nbsp;...

Here's what you'll need: * 10 M3 nuts * Arduino Nano ($2.79) - https://www.aliexpress.com/item/Nano-CH340-ATmega328P-MicroUSB-Compatible-for-Arduino-Nano-V3/32572612009.html * Step Down power supply ($1.09) -...

Are you interested in printing and selling OpenForge tiles? Find out more about licensing agreements and guidelines in our license FAQ. As an open-source patron supported project, I use the invaluable resources generously provided by my patrons to...

;-) I remembered this puzzle from back when i was a kid, seeing it at a flea market - and the contest brought it back to mind almost instantly.Although i took a slightly different approach to add a locked gift compartment, which should fit most gift...

I designed and printed this handle to fit the motor connected 3 18650 batteries, push button, mounted all of that and got a nice small low rpm cordless drill. Low rpm drills are needed in many cases for example for drilling wood and plastic. If you...

Plus more being added please see table belowSorry Painted in lettering and not double colour printingTaken from https://www.thingiverse.com/thing:3079639I used a draft setting, nozzle 215c bed 60c.&nbsp;Label ListAster American...

I printed the body and other parts, mounted the sensor in the sensor mount then glued the parts in place. As for the missing parts, get these from the original design that I remixed this from. ... Link to downloads for motioneyeos:...

If you make one or have improvements, please post. Print instructionsCategory: Costume Summary Here is my third version of a costume prop for Tom Clancy's The Division video game. It's some kind of shoulder beacon / gizmo that all the characters...

Steps: - Print the file - Slide the PTFE into its location at the desired length - Use a felt tip pen to mark the start of the contact on the tube - Take out the tube and cut it round on the outline as on the attached renderings - Replace the tube -...

To taper this wing just print the airfoils smaller and smaller to give the taper. So to reduce chord to 50% is easy. When you resize in a slicer it will tell you the length of the chord. So you just need to reduce this by typing the new value into...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   The...

There is also an experimental EDF holder, not even printed it yet, that would attach to the Body Lid or anything else. The base can be fitted and the two parts glued together. Just an idea but worth putting here. Again saw a Flite test plane with...

A height of seven and six-tenths was defined, corresponding directly With an expected final product size, we used primary color red and pattern overlap of eighteen Points precisely measured during each printing pass. As previously discussed above...

The dustshoe has a total of 5 parts that easily can be printed in three parts or maybe even less. It contains: A base part called Dustshoe basis (with the version on the end) Then a part to attach to your vacuum cleaner called Dustshoe...

As this model is in 1:10 scale, it is rc controllable and not a quick print!This is my second 1:10 scale “Lanz-Bulldog” tractor. Many parts are quite similar to my 1:10 scale “Eilbulldog” but I have optimized most of them. The interior is quite...

The only parts from the cad file I plan on printing is the pass through 4 way connectors. They are measured out so that a 3/8th inch Schedule 40 PVC pipe can slide through them and connect on either side. Technically with these connectors you could...

The only parts from the cad file I plan on printing is the pass through 4 way connectors. They are measured out so that a 3/8th inch Schedule 40 PVC pipe can slide through them and connect on either side. Technically with these connectors you could...

To build the gate and install the metal mesh, you have to print two times the stl called "Lateral_rejillasV2.stl" and put inside (like a sandwich) the mesh. You have to stick it with glue. Then, there is another part, called "Holder.stl". You have...