3d weapon models

 This allows me to use the device for watching TV/Movies on-the-go (using it as a stand) >>> then set it up as a dock next to the TV when when I arrive and control games & media remotely via a bluetooth controller.I have uploaded 3...

The base was redesigned using a few bits from the original model (the backdrop holder and part it was attached to). It has two places for the rail (horizontal and 45 degrees). I removed the rail completely from the Smartphone (frame) holder and...

link to original post: https://www.printables.com/model/21430-pi4-case-fancover-wcamera-slot Description Added screwless-jack.stl file! New Dome with larger Camera Slot New printing supports Also includes "Screwless Jack stand"... for those...

Also, be sure to increase the speed of infills from 80 to 90 mm/s as it's actually quieter (for me at least) with the higher speed. Revision logR1: Thinner onesR2: Thicker ones with tighter/better fitment R3: Even thicker ones with...

Instructions Components Needed: 1 x printed parts assembly (coil housing, chassis, slider, and capacitor) 1 x standard ferrite rod (four centimeters in length, having two flat sides) 1 x germanium-type diode (model AA112 or equivalent) 1 x 470...

Making some paper shims should resolve that though.All my prints were done with PLA using PrusaSlicer's 0.3 DRAFT profile for my MK3S.Layer height shouldn't matter much, but anything less than 0.3 should definitely work.If I was smart I would have...

### Printing Instructions This model isn't that picky about print settings, but you'll want to use a 0.4mm or smaller nozzle to make the jaws as sharp as possible. It also has a print-in-place hinge, so you'll want your printer to be relatively...

This articulated figure was made using the actual in-game model of the creature (with the help of MPR and URDE), with brand new joints added to every articulation. Most of the pieces are just as they were in-game, with some modifications done here...

https://www.amazon.de/gp/product/B08TZZGPVZ/ref=ppx_yo_dt_b_asin_title_o07_s00?ie=UTF8&psc=1 *2x* 50x4 mm O-Rings: https://www.amazon.de/gp/product/B00N3UZ0SG/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1 *6x* 3x20 mm steel pins:...

Note that the ears in the picture don't quite fit rack spacing, I uploaded fixed models and have confirmed they fit now, though the tolerances are somewhat tight. Let me know if you have issues. To build, just print two ears, then attach the...

Only some minor changes to increase the strength of the Jack-O-Lantern design were made since printing the models seen in the pics. I lost the back of the Jack-O-Lantern when I took the pics, but am re-printing it now, but it actaully looked OK...

This model will help install a Raspberry Pi in a regular ATX case, in my case a Fractal Design Define C case :) . "Why?" might be your first thought, Because I can! And its an interesting DIY Raspberry Pi project :) . ... Parts World Wide shipping: ...

** Design information and printing warning: This item has been modeled at half scale and will need to be scaled up to full size. Full scale printed length is approximately 39 cm (15.5 inches). Printing and assembly suggestions: Recommend...

If you are interested in other models from this movie check out my Spider-bot thing here: https://www.thingiverse.com/thing:4652780 If you enjoy my prints or remixes please consider becoming a Patron! https://www.patreon.com/rkxdesigns Becoming a...

You may also request this model printed and assembled with velcro at https://jkl-adapters.com/   **Description** To solve the tracking issues experienced by penholders while playing Eleven Table Tennis on the Oculus Quest 2, I created a series of...

Print Settings: Printer Brand: Printrbot Printer Model: Simple White Rafts: No Supports: No Resolution: 0.2mm Infill: 25% Shell Thickness: 0.8mm Print Speed: 60mm/s Notes: The x11 pins and x11 leaves need to be printed at a layer height of 0.1mm...

Please note that the first cone in the picture is a bit dirty since it was my second time using the support material.\r\nYou will need:\r\n- Printed parts\r\n- A rubber O-ring, 48mm x 44mm x 2/2.5mm (available on Amazon)\r\n- Slightly longer screws...

... each box is a different body, and STL combines them. If you don't do this (or combine the bodies in fusion) you may get issues when you slice the model.Open the meshes in your slicer, slice, and print.Please leave a comment if you have questions.

The model shown was printed with an extensive amount of tree support. While the overall structure held up, the undersides of the horizontal surface required a lot of cleanup. Fischer-Koch S Egg The Fischer-Koch S Egg has some overhangs that may...

This model was inspired by the G1000 10.4" flight simulator panel made by FlightSimMaker. (https://www.thingiverse.com/thing:4019943). The panel has the following; a Standby battery switch, Master switch/alternator, Avionics bus 1 and 2 switch,...

2021-08-15 Updated E3D_V6_Threaded.stl for better height adjustment, otherwise the official fan duct is too high ------------------------------------------------------------------------------------------------------------------------- This is my...

To arrive at the optimal model with desired results required me going through various iterations, which ended up taking time due to several complexities that arose. Despite being non-optional and thus having low modularity for reuse in future print...

You can find the OpenSCAD source here: https://github.com/simoninns/renault-twizy-speaker-mounts ## Printing instructions The model has been printed and tested on the Prusa MK3S/MMU2S printer using Prusament PETG filament. All parts fit on a 20x20...

... tastes. While almost none of the original remains, I still feel I need to credit that original box. So while I am not marking this as a remix, credit for the inspiration goes to this: https://www.printables.com/model/253827-ultimate-card-box-v4

Finally, after making several designs that interfered with something I hadn't modeled or were too tall, I have a working mount for the Zesty Nimble on SeeMeCNC's HE280/Rostock Max v3 hotend/printer. Step file included, once I get my nimble, I'll...

The final cable can now be run through the entire lower pipe and exit the tripod - Added "Dipole_Clip" for more sturdy transport - Still waiting for my soldering iron which was supposed to arrive four days ago 23.06.18 - Still waiting for my new...

I may have created a path inside the model for this if I had given it more thought. Other wire management isn't great either - currently, I'm using black tape on the back of the frame for most of it, but I'm looking for a better option.\r\n\r\nThe...

The design includes small "winglet" features to increase contact area where warping and model detachment are more likely to occur. ASSEMBLY: The visor is perforated using a standard 4-hole punch (office/stationery type) on the long side, then...

I highly recommend you remix here as necessary, as you almost certainly don't have the same 2 drives I have (and I don't recall the brands or models of mine offhand either, so I couldn't tell ya anyway). Finally there are portions of the build...

In the photo we use a 40+mm screw) (2) 6mm hex nuts (locking nuts would be better although not required) The following File is included: universal mount #1.stl Materials used to create model in photos: Overture Matte White PLA Overture Matte Black...