3d weapon models

My take has the following changes:Square nuts hold the screws connecting the control arms.Upper control arms now attach using M4 screws.The M3 screws connecting the steering knuckle are locked in place by the M4 screws.The updated cad model is...

I'm working on extras including:No-lock coverCash holderOthers (if it proves popular) …Extras mentioned are available for FREE at Printables: https://www.printables.com/model/758318-the-poly-wallet-slim-pop-up-walletGet permission to sell:...

I have added a dummy model in the stl files for rewference as well. ... W x H x L = 53mm x 23mm x 53mm 4 x 18650 LiPo batteries (recycled or new, just make sure at full charge they are close in voltages) 1 x 2S BMS 7.4/8.4v ...

I'm pretty sure this model has the fins set further back the the other two boards. My daughter just got her first paddle board, but I'm not super keen to have to carry all my gear and her board at the same time. So I needed an easy way for her...

So when I designed the sticker, I made each area a different height, so that I can apply the colours depending on height.There are 5 layers to the model, one for each colour except for red, which has 2 because the blue tends to show through. I use...

I modeled it in such a way that I could specify the wrist width and thickness, since these are pretty easy measurements to take. Then of course, you would want to specify the thickness of the band, as well as its length. There also needs to be an...

But then, if you try this on a complex model, you will quickly learn how easy it is to make mistakes missing areas that need support which often leads to a print getting ruined after hours of printing… and so you're back to using automatic support...

 I have no idea what long term effect this might have on an inline duct fan motor, but I'd rather destroy a motor than find out what effect stuff like that has on my lungs.Settings for slicing this model can be a little finicky due to the thin...

There are a ton of fascinating experimental aircraft, and even ships, that use Magnus effect wings, also known as Flettner rotors.This model dispenses with the tedium of wrapping rubber bands and desks in favor of a throwing stick to launch the wing....

Print Settings: Rafts: Yes Supports: Doesn't Matter Notes: PRINT EACH PART SEPARATELY Planetary gear prints can be done in the same printing bed if positioned correctly; avoid stacking them together, however, since assembled models have specific...

Important: This part has a support structure in a tricky place where you install the trolley handle, this is a cavity which is not optimal so you need to adjust your support settings so that they are easy to get out of there, I print with Cura and I...

Print Settings Printer Brand: Printrbot Printer Model: Simple Black Rafts: No Supports: No Resolution: 0.3mm Infill: 15%-25% Notes: I recommend using at least 3 perimeters because the screws may crush the plastic otherwise. I used 4 to ensure a...

 _________________________________________________________________ _____ This carriage is a revised design...

You can use for fixation of the MicroSD extender either attached SDclip model or heat both pins and "melt" them on the position. For better print quality all screws holes in the Cover (and also above the nuts holes in the main body) are covered...

To print this conversion kit, you'll need: * 1 Diffuser (the big star-shaped part that transfers air from the impeller into the volute) * 1 Volute (the snail-shaped thing) * 1 nozzle (straight or 90-degree) * 1 inlet bell (tall or short -- tall is...

Be sure to take care of the model of joystick and the buttons when purchasing from different sellers, as you may need six full buttons and the switches from another two buttons used for select and start.\r\nThe biggest part is 184x169x70 mms so any...

I have modeled and added a copy of the Spacer that goes between the extruder stepper and the aluminum plate that holds the wheels and belts. This part began warping for me while printing ABS in an enclosure, and I didn't like it (The original was...

If you've got slop in your bearings with the standard models, these gently modified parts may be of some use to you. ** Updated the spacer block so that it will fit inside the mounting clip ** -- ** Yet another UPDATE ** -- Found that the...

Added small supports to the cover pins, so model can be printed without the slicer adding supports. 5) Added Einsy-RAMBo / Mini-RAMBo / Retro-RAMBo Plate-Cover, will work with any RAMBo that has 95mm x 61mm mounting hole spacing, I recommend using...

They may be a bit sticky at first.How I Designed ThisAnother phone stand by Qrome inspired me to adapt my concept for a decorative plate stand in the sense of using a model of the device to cut out the holder shape from the part. ...Otherwise this was...

... blocks that attach to the supports. On a perfect fit, it should almost snap into place. Use superglue to ensure the wings don't come apart. However, I advise gluing the entire model together. ...Use your judgment based on the precision of the print.

Painted using golden Revel Model Paint 321 94 and weathered using black acrylic paint. Sight Leaf Clip The clip prevents sight leaf from falling out, while allowing it to rotate with a reasonable amount of force. The clip should tightly fit its...

You may also know this from higher specs models with their touch screen buttons, so someone at VW is peddling this crap and although these are "1st world problems" I personally think this person should never ever be allowed to influence a design in...

(The assembly of the plate should be explained by the reseller)Also use some additional M3 bolts to mount the washer cable strain relief arm to the plate.Use M3 bolts to mount the cable mount to the the washer cable strain relief armUse some self...

If anyone does wish to test this and would give me feedback so I can alter the design to better fit that would be a huge help for future modeling! Quick (theoretical) Set up 1- Remove the blasters front iron sight and bar that holds it. 2- Slide on...

If you get an error stating that the model is intersecting itself, either set the revolve to 180 degrees or cut the sketch in half and use a full revolve on one half. 5. Export and print! Print three times for the best effect. Place a flat object,...

All the DIN mounts will be uploaded to a separate model as they are Voron remixes. --- UPDATE 11/11/2021 Some more photos of how it looks. Currently waiting on right angle usb cable from RPI to MCU to have the electronics case completed. ...

You will need one strip for the 3V sphere which holds 42 LEDs, and 2 strips for the 3V model which holds 92 LEDs. It uses 1/4 inch drip irrigation tubing. The tubing I used came from Home Depot. ...

-Improved fang support on the right side -Double the airflow -Repositioned hot end fan for increased nozzle visibility -Modular wire management -Modular accessory mounts on each side (BL touch, CR touch, EZABL (coming soon), etc.) BL touch offset:...

[See this on printables](https://www.printables.com/de/model/186545-terra-mystica-fire-and-ice-all-in-base-game-box-ea) I wanted to store all items from the base game and expansion of Terra Mystica and Fire and Ice in one box. The existing solutions...