5e hit point tracker 3d models

The bottom spike had broken off so they needed some other form of support.I originally designed a single piece, support clip that snapped around the 1" candy cane and had a couple of stabilizing points on the base that stuck into the ground. The part...

At this point gently push the 3D-Benchy into the blue resin in the silicone mold (this way the Benchy seems to swim and not only sit on top of the “water”). Let it cure. Mix another batch of resin one or two days later (clear resin this time), degas...

I got some inspiration from seeing this thing, and I used gpambrozio's customizer friendly thing here as the starting point for the case. There is a big compromise on the power supply in order to fit it in the Stanley case however. Due to the low...

fence gate: The entrance point of many homes, composed from an impressive number of precision-designed triangular elements amounting to a total count of 86 individual shapes for maximum authenticity in digital world construction. More Details on...

From a mechanical point of view, the dimensions and fittings have been reviewed in order to tune mechanical clearance and friction as much as possible. So that it can be offered as a gift, I wanted to make it a very qualitative object both by...

The X endstop is designed for a bowden style carriage with a small contact point on the lower left hand screw on the carriage itself. You will need to design this until I can remake my file of one, more or less a 5mm spacer. Please use electrical...

**Update March 15 2019** It appears that the step-up converter generates a high load even at 3V, preventing the rotor from reaching an efficient operation point. To avoid this issue, insert a threshold switch (around 6V) into the input line of the...

Invert the smaller end piece, such that both openings are on the top.Remove heated bed surface.Attach the top and bottom Y mounts to the drag chain, using two M3 countersunk bolts and nuts per side.Thread all heatbed cables though the drag...

I thought while I work on my “hero” versions, I thought I would share my files and research to this point. This is based off of a lot of research of the Tempad from what has been seen on and off screen. How accurate is this? Please understand that...

... TIP: glue two washer below the starting points of the magnets inside the maze. This locks the magnets in place. Do test first to see if the disk magnets are strong enough to pull the maze magnets loose from the washers, if not: use smaller washers.

... lot of time and money buying parts I wound up not using, unnecessary tools, and lots of wasted filament before I finally got it down to what you see here. Looking back at it, it does look simple, but it did take time to get to this point. ...Thanks!

The standard TAZ mount has the motor up high, and offset towards the front of the machine, the farthest point of the motor 82mm from the X carriage. My placement puts the motor 36mm closer to the carriage/rails, which should reduce any...

The Barrel improvements: The weakest point of the barrel is now much fatter, and the entire barrel diameter is larger. Original Hilarious YouTube Homemade Commercial: (April 30, 2021) https://www.youtube.com/watch?v=vSHd0pNM9u0 Assembly...

This is by far the weakest point of the design but if you have a larger volume printer and can print the whole piece I would highly recommend doing that. The tolerances are very tight (definitely not because I neglected to include tolerances at...

The Catan Hex-Storage Tower What I didn't have at this point was a good solution for storage and use of the resource cards for the game. Therefore, I designed something that works for me and I hope will be of value for others as well. My storage...

You will need to position the gap in the circlip so that it is pointing down. Make sure you loctite on the pusher nub to hold this into position. This is the leading cause of jams. **Special considerations for the 35mm solenoid** These come with a...

The short T-nuts on the front of the rails go in the slot that's now the lowest point on the printer, that is, the far left slot on the underside when the printer is upright. This puts the front of the drawer just about flush with the left frame...

However the size difference and the large M600 silver 3 across the multiple bars makes for an easy differentiation and easier to score at the end. I used the gold tiles from mnemic (see below for the great tokens) as a starting point for my gold -...

A rather gigantic cockroach, whom had set up shop in his counterlung at some point before he assembled his stuff. And, Mr. Cockroach stayed there the entire dive (I mean really, what choice did he have?), and.. was still quite alive and well...

Remember to insert the magnets at this point.On the underside of the thruster's handle (left side), remove the two screws. Since the clearance is very small, a screwdriver will not fit. I had to use a detached <a...

I have 3 of these up high in my living room, and the savings of USD$120 for the same effect were well worth the effort. A few notes on assembly (read all points before starting):The width of your window opening will not be the width of your shade,...

&nbsp;You might notice all images from the famous “Hubble Space Telescope” have four pointed stars, and JWST's images all have six points (ignoring all the other diffraction artifacts). &nbsp;This is due to the secondary mirror support – and with...

Assembling Start with "ring-base." Hold it such that the angled connector sticking out points downward rather than upward. Place "ring-flex" on top of "ring-base." It shouldn't ultimately matter, but I prefer the way it looks for the fold lines on...

At this point, you should be ready to put the back on the frame. Take the white piece of paper and rough cut it a little bit smaller than the backing plate. Put two pieces of tape on it and tape it down to the side facing the lithophane. This...

To glue the arms and the ring: if you have printed them in ABS, just put a drop of acetone on each gluing point, hold the parts together and let them dry for about fifteen minutes; if instead you have printed them in PLA or other materials, the...

Since the core can only move vertically, the inner wheels must be rotated so their keyways point upwards, only then can the core slide up and out. The keyways line up with one of the 8 symbols depicted on the outer dial, and you can choose which of...

However you choose to deal with them after trapping is up to you - spray insect spray into the entry point, drop it all into water until they drown... or just open the end sliding door, knock them out and squash them. Whatever method you decide on at...

First, I want to thank @bld for his/her beautiful model of the Earth as well as well as @gabriell for her/his realistic model of a pointing hand. Without these, this would have never come to fruition... not with my modeling skills anyway! [I...

If you do not the Wemos will create it's own WiFI access point so you can connect your phone or computer directly to the Wemos and controll the LED strip. (There is also a WLED app for Android/Apple device if you do not want to use your browser. ...

Optionally, you can lubricate the pivot point of the handle before assembly, to make sure it moves smoothly. You may want to use some supports on the handle, especially on some of the letters. ####**Printing** For this project you will need...