Extruder Upgrade for Flashforge and CTC 3d models

This upgrade design is derived from the original Thing uploaded by Coldstone for Flashforge Creator and CTC machines' OEM, unsprung feeder parts. The spring-armed feeder upgrade initially designed by whosawhatsis has been redesigned in this...

http://threedprintingtoday.libsyn.com This is a derivative of the Thing uploaded by Coldstone. This thing is meant as an upgrade to the OEM, unsprung feeder parts used in older Flashforge Creators and in the CTC machines This is the spring armed...

Update April 1st, 2015: I changed hole diameter to 11.8 mm, so you don't need to sand it down, moved the filament hole a bit, and made a bigger diameter hole on the bottom so it doesn't touch the gear fastening screw Update March 31st, 2016: Since...

Redesigned extruder block with smaller drive gear hole (11.8 instead of 13 mm) -> longer filament support between the drive gear and hot end so flexible filament does not get stuck in between. As CTC that I own is an Makerbot Replicator 1 (dual)...

Print Settings Printer: CTC CTC Rafts: No Supports: No Resolution: 0.2 layer height, 3 top surfaces and 2 perimeters for optimal print quality Infill: 20% for a balance between strength and speed Notes: If the inner diameter of your rails is too...

... a cable shield at the top of the assembly. The top component comes in two distinct configurations: one equipped with threading for PTFE-Tubes and another without this feature. ...Apologies are offered for the subpar image quality provided.

... the Lightweight Extruder conversion. I added a cable protection on the top part. ...The top part comes in two version: one with the thread for the PTFE-Tubes and one without. Sorry for the poor pictures. Print instructionsCategory: 3D Printer Parts

This thing is a base for a CTC, Flashforge or similar 3D printer. You will need four of them. It's possible to use just some kind of "grip pad," but I recommend using additional case feet if they are available. I got my case feet from the online shop...

... I also designed an optional power cord mount as a bonus feature to complement the top cap. On the power cord mount, I applied m3x20mm countersink screws and two nuts each, one to form studs and the other to fasten down the piece securely.

... is the rewritten text. ... Human: Close-off nozzles for Extruder Blowers, choose from either 5.5mm or 6mm diameter. ... Print Settings Printer: CTC Dual Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 mm Infill: 100% Notes: Two shells

... Original Housings Are Difficult to Remove During Assembly. ... This Solution Eliminates the Problem. Print Settings: Printer: CTC Dual Rafts: Any Setting is Fine -or- Raft Supports: Off Resolution: 0.16mm -or- 0.12mm Supports: Off Notes: One Shell

I upgraded my extruders on the CTC and created a custom cover to fit them. The Makerbot Replicator 2X Full Metal Extruders I bought from ebay required an angle cut for their sprung hinges, as the original cover wouldn't let them close tightly enough....

CTC Spring Loaded \r\n\r\nTwo Precision Ball Bearings 8x3x4\r\n\r\n

The kit includes an extruder plate with cable management and sockets for 4mm tubes' M6 push-in connectors, a back mount module with similar features, and M6 sockets that require thread cutters to finish. Prerequisites involve a 1m 4x2mm PTFE tube cut...

LCD Hole Cover for CTC, Flashforge and similar printers protects the LCD display underneath from falling objects such as screws, nuts or filament parts. It is extremely flat when installed, standing at only 5-7 mm high. I designed sloping sides to...

... an improved version over headGuideTry2. ... This is a 6mm PTFE tube and cable holder for my CTC printer. ...The PTFE holes are centered (original Replicator file are misaligned 0.1in from the extruder hole feeders) Solidworks file included :)

... FlashAir SD-Card. It also works well with 31x7mm SD-Card-Holder holes. Here are my print settings: Printer: CTC Rafts: None Supports: None Resolution: 0.2 mm layer height, three top/bottom surfaces and two to three perimeters Infill: Twenty percent

I wanted to shed some serious light on my CTC printer, and I knew the more lumens were always better. To fasten those sleek LED Strips in place, I conjured up fixtures tailored for every axis. I took note that X-Axis needs four printings - just...

... facing upwards, so no supports or rafts are required. Printer Settings Printer: CTC Rafts: No Supports: No Resolution: 0.2 mm layer height, 3 top/bottom surfaces and 2 perimeters Infill: 20% Notes: Adjust the size to fit your printer perfectly!

... images do not show my most recent configuration with the fan cables located underneath the new plate. A notable detail is that there are 34 mm between the two holes of the extruder; my Flashforge Creator Dual printer has this particular dimension.

Spacer for MK8 Extruder Fan/Heatsink Incorporating SN04 Mount. With Arm to Position Sensor Level with Nozzles on Left Hand Side. Remove the fan and spacers, add this attachment; securely fasten the SN04 probe in its new position. You Require Marlin...

Here's a Halter for the CTC Slider. ...This Clone is installed:...

... drive gear slipping or skipping when employing material with inconsistent diameters. ...This innovation is a modification of another upgrade on Thingiverse, designed specifically for Flashforge Creator Dual Extruder models featuring grooved bearings.

I upgraded my extruder to "MK9" and added a 4mm PTFE filament tube. The connectors for the tube, PC4-01, are 1/8", so I increased the input hole's size slightly from the original part. To screw in the connectors easily, I heated them with a hair...

***EDIT*** I have to say, my experience is that the original Geeetech extruder is actually better than this upgrade. It just needs a bit of TLC. For me, the biggest issue was the screws holding the fan to the motor block. They shouldn't be too tight...

This solution converts a dual to single extruder setup, securing cables and integrating a fan and air duct for object cooling. It's best to print at least the top part and nozzle in ABS plastic. Otherwise, the top part may warp due to motor heat,...

This my new base for hotend. ...Without this radiator i have jam filament in hotend. 2017-03-21 Add screw for correct work x-max endstop.

Use a BMG extruder and V6 hotend on your CTC Bizer, Replicator Dual or Flashforge Creator

Key Features of the Modified Bracket: The bracket can accommodate two extruders and has channels designed to keep stepper wiring out of the way. The adapters have been modified to use M3 screws for a secure fit. I extended the bearing bore on the...

The CTC Bizer and Flashforge Creator both benefit from an angled LCD display holder. This accessory is specifically designed to complement these 3D printers, providing a convenient way to view the print job without having to constantly look down at...