FlashForge Creator Leveling Feet any MakerBot actually 3d models

This improved dome has been designed specifically for FlashForge Creator Pro and provides several upgrades compared to the stock version: Better filament path: The new design moves freely. Improved heat enclosure: Since the opening is located at...

I've added a version specifically for printers with round feet - there are two options: one has a full slot for the foot, which requires support, while the other has one side cut off to print without any additional supports. Check out the Made ones...

The following settings were used for this print: Printer: FlashForge Creator Pro Rafts: No rafts were needed for this print. Supports: Yes, supports are included in the design to prevent warping or sagging. Resolution: The resolution of this...

Use these brackets to attach rubber isolation pads securely to the Flashforge Creator Pro. The brackets replace standard covers that usually sit on printer bases. ...Replace rubber feet pads with JW Winco GN 451 Cylindrical Vibration Isolation Mounts...

Upon reading his description, I began researching a budget-friendly way to obtain Sorbothane in a configuration suitable for the FlashForge Creator Pro. Online, I discovered a set of four 1.5-inch hemispheres by Isolatit with a durometer rating of 70...

Summary Mount for Flashforge Creator Pro (and probably all MakerBot clones) Smart camera available on AliExpress: http://www.aliexpress.com/item/Sricam-SP009-Wireless-IP-Camera-WiFi-HD-720P-indoor-1-0MP-P2P-720P-Video-IR-Network/32603411551.html...

This is a quick remix of the filament feeder for the Flashforge Creator Pro 2016, designed by Vexelius to allow printing entirely without supports. ...Print Settings Printer: Flashforge Creator Pro 2016 Rafts: None Supports: None

Deeper guide tube retainers for the FlashForge Creator Pro ensure that guide tubes stay firmly in position. ...This add-on bolt securely attaches to the FlashForge Creator Pro's extruder assembly using readily available parts.

... Creator Pro 3D printer. In summary, an air-tight seal or plug for the Flashforge Creator Pro 3D printer port is a must-have accessory for any serious user looking to optimize their print quality and ensure smooth operation of their device.

One of the extruder filament inlet caps broke off Flashforge Creator 3 printer, so I designed a replacement.

This is an updated version of Vasilyd's GoPro mount tailored specifically for the FlashForge Creator Pro 3D printer.

This is my initial design submission for Thingiverse: a 3kg spool holder tailored specifically for my FlashForge Creator 3. The spindle is mounted at a 45° angle to the printer's body, and it features a 5° incline to prevent the spool from toppling...

This mount fits both a GoPro and a webcam (or any camera of similar size with standard tripod mount) right onto the front of a Flashforge Creator Pro 2016.\r\nWith cameras taken off, the door still opens and closes fully without removing the mount...

... filament in them. ... Print Settings Printer: Flashforge Creator Pro Rafts: Disabled Supports: Disabled Resolution: 0.2 mm Infill Percentage: 20% Post-Printing Instructions Inspect the print and lightly sand any parts that are too tight for a snug fit.

... tube holder designed specifically for a QIDI Tech-1 printer. ... It's also highly likely to fit the Flashforge Creator since QIDI essentially replicated that printer's design. ... To print this replica, place it face down and avoid using any supports.

The shape is designed for the flavors of the FlashForge Creator Pro (2016 edition) that have the long-shaped feet, but they will fit any machine that has ‘feet’ shaped like a rounded rectangle of about 48×17mm, of at least 2 mm high. Of course you...

FlashForge Creator Pro 2015/2016 other generic cased 3D printers remixed with a cam mount holder, precisely designed for the rear left corner to securely hold your camera in place. This ingenious mount eliminates the need for an additional clip as...

... Printer Settings: Printer Model: Flashforge Creator Pro 2016 Raft: Disabled Supports: Required for easy removal from the print bed Resolution: 0.2mm Infill Percentage: 15% Printing Recommendations: ABS or PLA can be used for printing this piece.

After discovering that pre-existing designs for filament tube holders wouldn't fit inside my new FlashForge Creator Pro, I made the decision to create my own design.\nThis is the second version, designed entirely from scratch! The piece's dimensions...

FlashForge Creator Pro Extruder LED Adapter WARNING You can use it only on the front side of the extruder. ...If you want to use it on the back, you'll have to remove the Flashforge Logo Plate

... Interestingly, I recently found maxy's Ultimaker version which resembles mine for the Creator, but it's unclear if it would work for the Creator; you might need a left and right hand version of maxy's, while my design fits both left and right feet.

Once you've got it spot-on, level your bed and reprint if needed.\n\nGradually lower your bed by twisting the levelling screws, allowing for a 0.5mm clearance from the nozzle to avoid any unexpected surprises during installation.\n\nSimply place the...

The original open source 3D model of the makerbot replicator does not really help unless you are lucky because the clones are changed here and there without any documents... It is like solving a 3D puzzle to get this right, the corner is tricky...

Adapter for Flashforge Creator Pro 2 original spool holderThis adapter mounts to the original spool holder allowing you to use third party filament reels

New spool holder for old-type (wooden) Flashforge Creator. Fits standart 1kg filament spools. ...You should rotate holder model upside-down in your slicer.

This design draws inspiration from the Flashforge Creator Pro 2016 top plate, tailored specifically to accommodate the Bondtech Extruder Upgrade, model EXT-MBK-5.

This Dial Indicator holder, designed for FlashForge Creator rails, features a central 8mm hole and two 6mm x 6mm magnet-holding holes. ...Simple to print and install.

3D printed - Integrated Extruder cover and Filament Guide for a FlashForge Creator 3. ...Both left and right covers are included in the files.

This mounting system securely positions a 60 millimeter fan over the extruder of the FlashForge Creator Pro desktop three-dimensional printer.

A handy slide-in replacement part for flashforge creator pro printer spool holder removal - simply plug it in to cover gaps.