PIR Motion sensor case 3d models

EDIT: 02/06/19: Added remix of a pi zero case to run the printer without a PC: https://www.thingiverse.com/thing:3668215 EDIT: 19/05/19: Added a mount to attach the titan extruder motor next to the printer. EDIT 18/05/19: I have added new "carriage...

I designed this Nintendo GAME MAN case for fun. It's completely impractical and pointless. It was designed to fit an original Famicom motherboard and 5,6" 640x480 LCD, but can off course be used for any hardware, for example Raspberry Pi, with the...

In case you want to fiddle around with a brim yourself, there is a "naked" version included. For all the lazy folks out there, I have included a version with a designed-in brim, that works very nicely for me. If you are not sure, you cannot make a...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

The most significant bit is ignored (is always 0 in this case), because we have only 7 LEDs, thus need only 7 bits. The for loop in the showNumber function sets the state of each LED according to the definition of number symbol. The sketch is very...

Both a one piece rocket body as well as a split rocket body (with pin) is supplied in case your printer Z-height cannot print the one piece. My print contains the two piece rocket body, with the seam hidden by the middle rope. 4 - Optional ears...

You have to wrap it into thin paper prior closing the case. The gift looks better, stored in this box. I chose ironing before slicing both box parts with stunning effect on the upper layer. Bill of material: all printed details, as mentioned...

Perimeters are probably the deciding factor for strength but I think default settings will work perfectly for almost all use cases.  STEP #2: STRINGINGStringing this scope is no more difficult than a scar barrel. THE POSTS ARE MEANT TO...

Both a one piece rocket body as well as a split rocket body (with pin) is supplied in case your printer Z-height cannot print the one piece. My print contains the two piece rocket body, with the seam hidden by the middle rope. 4 - Optional ears...

Do not overtighten.Cut out an appropriate length from the fan leads (in my case it was 24 cm), strip the shrink tubes onto the leads before soldering, moving them away from the soldering points as far as possible to avoid shrinking them prematurely...

There is one part I recommend printing at a smaller layer height, which is the net, as it has very small details and it'll look better, I printed it at 0.15mm.Infill: 20% for all the part minus the pole which I used 100% to make it a bit heavier and...

  I suggest a maximum layer height of 0.15 or lower for the domed button.  I used MKOEM Silk Silver for the silver parts. The best filament I have found so far to replicate the pink acrylic used on the original rectangular button is Fillamentum Pink...

The setup should allow you for a 270 degree swivel of the display if you use the special bracket... ...This will come with a BTT TFT7 case, so I also did this for the 7inch display: https://www.thingiverse.com/thing:4883408 ,but you should also be...

EDIT: 02/06/19: Added remix of a pi zero case to run the printer without a PC: https://www.thingiverse.com/thing:3668215 EDIT: 19/05/19: Added a mount to attach the titan extruder motor next to the printer. EDIT 18/05/19: I have added new "carriage...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

In any case, since then, at that point, the association has moved from 'off the rack' replies toward their own, down to earth format that meets the cravings of its clients. Developed to incorporate different on-point highlights for purchasers, the...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

There is a whole cap for capping one tube, bottom caps that hold 3/8" or M6 hex bolts for attaching the tubes to your pack, and a cap with a .375" hole intended for accepting a Clippard hex fitting for one of the tubes (there is also an insert for...

Which one you print depends on which side of your drag chain links open up -- if they open up to the outside, pick Open Max, but if it opens on the inside, pick Open Min (Min/Max in this case referring to where on the X axis the drag chain opens...

I am located in Vancouver, BC in case anyone local has any needs. Note I had this mask tested by a professional respirator fitter at work today and it performed quite well considering its limitations. However, it did fail the irritant test along the...

I do not receive anything from the creator of the Death Star in case you make your purchase! MoodDeathStar Repository URL: https://github.com/pstimpel/MoodDeathStar A moodlamp and a Death star once had a one night stand... Video explaining this...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

An iris door will seal the dome from the rest of the base in case of an integrity breach. The lower levels are composed of: 2 working rings (around the central axe), 1 habitat ring (around the central axe), 1 ring for machinery & Generators...

Sherlock and Watson 221B BookmarkA Sherlock and Doctor Watson bookmark with 221B and matching wallpaper design!If you have any questions about the design or how to print, please let me know in the comments and I'll be happy to help.Before You...

In my case I was a bit disappointed with the bearings in the idlers, so I did use self securing M4 nuts, which allowed me to not tighten them completely and give the idlers some additional play to rotate freely.If there should be other pitfalls for...

Depending on tolerance, the pins may not be super tight, in which case you should glue the pins to one side and let that fully cure (after mocking the pieces together to ensure fit). Then add glue to the end of the pins or the opposite holes and...

Both a one piece rocket body as well as a split rocket body (with pin) is supplied in case your printer Z-height cannot print the one piece. My print contains the two piece rocket body, with the seam hidden by the middle rope. 4 - Optional ears...

The length of the screws depends of you setup, the case measure 30 mm.  12mm Push Button Switch - https://www.aliexpress.com/item/32896221862.html?spm=a2g0s.9042311.0.0.27426c37R7cspc 2 Micro switch for the shifters -...