SciFi Mobile Command Center 3d models

The models (keys and legends) are the same dimensions and should center at the exact same spot. It’s really difficult, and you will fail again and again, but the result is worth it (I think). You could also print the keys upright (with supports) and...

Although, a tiny piece of double sided tape on bottom center of mount or a little bit of Loctite Fun Tak or Poster Putty can help if its not super secure side to side.Lastly, if you are just starting out and unsure how to size the legs, send me a...

I always wanted to design and print a swamp boat. Now it was time to realize it. The boat consists of two parts, which are screwed together. For sealing the whole thing is glued around the internal cable duct. I took the motor and ESC out of my MHQ...

*Be especially vigilant about this step if any adhesion technique was used.* **2.** *Gently* disjoin each of the 3 curved arms at the top of the body from the hexagonal surface beneath by pushing from the ends of the arms toward the center of the...

The optional stalk that sticks up is specifically to keep the lid from pressing on the spool and causing drag. UPDATE 10/1/2018: I uploaded a working brace to keep the spinner centered in the Sistema box. It expects a 70mm spinner, so make sure...

###Filament change layer for colours on "PreludeBoxBack": 1) Start (Colour of the background, mine is in white) 2) Layer 14 (All logos outline colour, mine is in black) 3) Layer 19 ("Classic" lettering, Honda logo, "Honda" lettering and Honda...

  Ether add a center of support or  pick a socket with larger tolerances for printing on the side.For those that want design thing using the 3UDC clip and socket, please visit the developers library for parts and technical information.Other...

### Notable Autostar configuration parameters Telescope - 4504/114EQ if FW patched, otherwise DS-127 Alt/Dec Ratio = -03.28533 (1:144 worm ratio) Az/RA Ratio = +03.28533 (1:144 worm ratio) Alt/Dec Percent = 75% Az/RA Percent = 75% ### Parts list 2x...

The L shaped inlet needs to be placed close to the edge of the lid, while the straight outlet goes near the center of the lid. Be sure to space everything out so you have some room to turn the nuts. I used a sharpie to trace the parts onto the lid,...

Length over all 170 mm.Couping hook fixed in newer VersionYou will need: 1 ea frame (rahmen)2 ea axle (Achse)2 ea sleeve (Achshuelse)4 ea wheel (Rad)4+x ea pin (Achsclip)2 ea support for hutch (KipperStuetze)1 ea hutch (KipperMulde) Prepare...

Changes for V3: Replaced single center lid screw with 4 perimeter screws. This helps with lids that bow slightly upon removal from the printer due to internal residual stresses generated from differential cooling during print.<br/> Enlarged wire...

To reach the screws you can use a small torque wrench OR print the small wrench I have uploaded here.&nbsp;Its a remix of https://www.prusaprinters.org/prints/16562-bit-handle/files&nbsp;This is one of my first print in place designs. I uploaded a...

In this project, a 3D printed wheel with a five-inch diameter and three-quarter inch thickness was created, along with an axle inserted into the center of the wheel and glued to it. The motor, located directly under the wheel, was pressed into the...

The plots of each short usually center on Tom's numerous attempts to capture Jerry and the mayhem and destruction that follows. Except for the body, no other supports are required. An optioanl part, body_with_supports, is supplied with built-in...

Support came from a layer of closely packed leaf bases just below the surface of the trunk, while the center of the trunk was filled with pith. The trunk had photosynthetic tissue on the surface, meaning that it was probably green. Long, thin leaves...

The inlet to the valve is tangential to the valve's toroidal section, offset laterally from the center of the body of the valve where the outlet funnel extends downwards from and 90 degrees deviated from being parallel to the valve's outlet. The...

The unit system employed is centered around metric measurements (centimeters). Notably, the model operates under real-world scale parameters. A variety of export formats, specifically targeting collapsed mesh settings, have been made available for...

upper_arm_parent.L and upper_arm_parent.R are controllers of legs, their customized attribute FK_limb_follow controls whether the legs rotate following the center of gravity in FK mode; IK_FK controls the non-seamless switch of IK/FK of the legs;...

The PC4-M10 connectors to use are the ones where you can push the PTFE tube through (that is because the PTFE tube will be pushed into the air injector, to exactly center them and to allow hazzle-free filament loading). You only need 5-10cm PTFE...

Majolica includes ware made of baked clay and covered in tin-lead glaze. They are produced using a technique originating from the Middle East. Over time, the technique also spread in the Iberian Peninsula and subsequently, in Italy. The majolica...

If you don't have any prusament spools, you can either print the Extra Layer model or make a disc out of wood or other rigid material, where the disc has an outer diameter of 20cm and a hole in the center with a diameter of 5cm. Both the...

The second component is the mount itself that is fixed to the bike using the bike's bottle cage mounting points (M5 screws, 64 mm on-center). The mount securely holds the U-lock using a toggle-action latching system.</p> <p>I've provided the STL...

It's due to the weight of the monitor having a lot of leverage against the small off-center foot print where the mount connects to the monitor. I used filament I had laying around that I paid < $15 a roll for and I already had the screws and nuts...

Resize and center the QR code so it fits in the space above the WiFi icon on the sign part. In my sign this works out to be approximately 64mm^2. Set the height of the QR code object such that it extends 1mm above the surface of the...

I still plan to tweak the design a bit more before moving on to cutting/gluing the folio cover on (I still don't like the power/volume button area, and the camera/fingerprint cutouts are about 0.4mm off center). I'm guessing about 1-2 more design...

Put them together so that the bar is flush with the side panel.Step 3: Installing the Remaining BarsGo on installing the remaining bars.Apply a little bit of superglue to the teeth and then press each bar firmly into place.Step 4: Installing the...

To assemble it, slide the horn section into that center hole and align it with the internal lip inside the case; just as long as the mouthpiece sits snug. Now place that lovely new diaphragm inside, rest it on the internal lip - voila! Assemble...

Final Note: I have been using the four-piece center frame design because of printer size restrictions I had at the time, for just under three years now. The only issues I’ve run into were with the wall mount layer separation mentioned below. Besides...

I'm also working on a landing system based on this one that uses standard size carbon fiber rods and all 3D printed parts, with a modular battery box, adjustable center of gravity, and a mount for an F450/F550 style multicopter that's cleaner than...

the magnets of the 3 seats in the center are wedged so that they are lower than the print bed. Wedged inside the seats they must create a 1mm step on the edges, this serves to better contain the steel ball without making it go beyond the seat of the...