a10 model

Get rid of the sloppy wires that rub against each other during prints on your Ender 3 or A10 with this simple mod. Designed to work seamlessly with a stock hotend setup, it adds a neat and tidy cable chain from the hotend to the extruder of your...

Boquilla de ventilación para Hellbot Magna I o Geeetech A10 - A20 con fan de capa 5015. La Boquilla a pesar de ser unidireccional, tiene una concentración del flujo de aire que lo hace mucho más eficiente, es corta de tamaño para reducir las...

This piece is a modification of the Direct drive mount for Geeetech A10 (stock parts) by Woyta94 https://www.thingiverse.com/thing:3293736, to match the holes for fixing and filament guide with the original extruder dimensions of the Magna 1 printer....

Cabezal pensado para la hellbot magna 1/Geeetech A10 cuando se ha decidido cambiar al sistema estilo e3d v6. Si bien es un kit generico el que implemente, es marca Triangle lab, que es muy fiel al original. Antes de efecturar cambios se sugiere...

Boquilla de ventilación para Hellbot Magna I o Geeetech A10 - A20 con fan de capa 5015. La Boquilla a pesar de ser unidireccional, tiene una concentración del flujo de aire que lo hace mucho más eficiente, es corta de tamaño para reducir las...

This requires the original A10 metall display holder. I also uploaded an additional Left Side Holder for a Raspberry Pi: https://www.thingiverse.com/thing:6156490 I made this for the 5inch Waveshare DSI Touchscreen to be connected via 15 pin...

Ballbearings from old V-slotweels, stehhlplate form orignal A10-filamentsensor or similar useable peace, 6mm GT2 timingbelt 614mm long, 2 pieces of t8 lead screws and backlash-nuts, 3 peices og gt2 pulleys whith 20 teeth.For this upgrade is much work...

Inspired by BennyBoyW's Geeetech A10 BLTouch Mount I wanted to be safe from my clumsy moves and create a stiff version which is aligned in a well-defined way, so that the BLTouch always stays in position, almost no matter how hard I hit it...

I'm really excited about my future project with my Geeetech A10. Absolutely, I haven't tested it yet! One thing I love about this printer is the metal cage - it's an amazing natural heatsink for the hotend. However, the 30mm fan inside makes way...

A10 and A10M require a 300m guide: http://s.click.aliexpress.com/e/_srmsaq There are three solutions: A - that one I used and tested. It is composed by original carriage + printed plate + modified Petsfang + X endstop. B - just full cage for using...

Update 10.10.2018: A newer A10 was spotted in the wild, with filament sensor and Power out feature, which has the GT2560 v3.0 board. This firmware should work but was not Tested on the New Firmware. Update 31.08.2018: some of you might be getting a...

Update 10.10.2018: A newer A10 was spotted in the wild, with filament sensor and Power out feature, which has the GT2560 v3.0 board. This firmware should work but was not tested on the new firmware. Update 31.08.2018: Some users may be getting a...

Ich habe mir einen Abdeckung für das Board meines Geeetech A10 entwickelt weil ich bei sehr lang dauernden Drucken ab und zu das Problem hatte dass die Steppertreiber zu heiß wurden und ich Schritte verlor, aus diesem Grund hab ich mir einen 60 x 60...

Since I don’t have the A10 I can’t confirm, but the cover should fit on the regular A10 as well. A feedback is appreciated if it fits, so I can put it into the description. Additional parts needed: 2(4) pcs. M4x20 allen bolt Assembly: 1. Disassemble...

This design should work with other Geeetech printers like the A20, A10, and A10M. To get this set up right, you'll need a radial fan for cooling. The mount also provides support for BLTouch or equivalent sensors. I opted for the Chimera (2 In - 2...

Get rid of the sloppy wires that rub against each other during prints on your Ender 3 or A10. ...Designed to work with a stock hotend setup, this mod adds a neat and tidy cable chain from the hotend to the extruder of your printer.</p> <p>To mount chain...

This is a custom fan duct for Madzumo's Geeetech A10 hotend mount tailored to the E3dV6 hotend and its clones. The original fan ducts were excessively long and would occasionally rub against parts being printed, which was unacceptable. This may be...

The 40pin FFC cable on my Geeetech A10 had a bad habit of falling out of the control/LCD panel, because the cable is entirely too short, and the "locking" mechanism of the FFC FPC connector simply doesn't work because there is no strain relief...

... This remix includes a modified back piece that fits the hot-end mount plate on the Geeetech A10 and A30, as well as a modified BLTouch mount. On the back piece, there are now 2 pairs of holes, one above the other. I ended up using the top most set.

This is a precision dial indicator mount specifically engineered to fit perfectly onto a Geeetech A10. The mount's sleek design accommodates an indicator with a diameter of exactly 8mm, ensuring a snug fit that eliminates any unwanted wobble or...

My Geeetech A10 is set up with a 220x220 bed size, perfect for the job at hand. To get the best results, I've opted for a 0.4mm nozzle - that way, the wall thickness will be just right. My first layer comes in at a height of 0.3mm, and from there,...

This design marks a significant leap forward over the standard Geeetech A10 part cooler. I fine-tuned the airflow to maximize cooling efficiency, directing it precisely where needed without generating turbulence. By streamlining the air flow, this...

Get rid of the sloppy wires that rub against each other during prints on your Ender 3 or A10. This mod is designed to work with a stock hotend setup and adds a neat and tidy cable chain from the hotend to the extruder of your printer. To mount chain...

One potential drawback of direct drive is that it may introduce more ringing due to the added weight on the printer head, but I haven't noticed this issue with my A10 (acceleration: 500, jerk: 10, speed: 50 mm/s). INSTRUCTIONS: 1) Cut the PTFE...

The new version features a spring-loaded mechanism designed to enhance the repeatability of the Z homing process, offering a slight improvement over the basic model. Print this part in the orientation shown in the screenshot provided. Assemble it as...

... To assemble this bracket, you'll need: 5 M3x20 screws 4 M3 nuts The Ender 3 - Filament holder DELUXE (http://www.thingiverse.com/thing:3114139) is a great addition to this setup. FreeCAD models are included for your own customization and tuning.

• Creality ender 3 | 3D CAD Model Library | GrabCAD (2023). Disponible en línea en https://grabcad.com/library/creality-ender-3-2, Última actualización el 19/01/2023, Última comprobación el 19/01/2023. • Diagram. Disponible en línea en...

The stock cover on the A10M printer is incredibly loud, and existing covers designed for earlier models are too large to fit around the upgraded bed levelling dials found on the A10M. I decided to attempt creating a new cover that would redirect...

It's based on a CAD Model of a Raspi 4, not on an actual Raspi 4. So I'm not sure if it is 100% accurate. ... <b>Additional parts needed:</b> 4x M4x12 Socket Head Bolt 6x M4 Washer 4x M4 T-Nut 2x M4x10 socket head bolt 4x M3x5 mm Socket Head Bolt...

I built this toolbox specifically for my A10M 3D printer, but it should be compatible with other similar models like the A10 and Ender 3.